• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.11a
• /
• pp.94-97
• /
• 2008

As the partial admission turbine has a intrinsically unsteady and three dimensional flow region, numerical calculation time of these study has been too long time. The numerical analysis for gas temperature of turbine blade surface has been performed to investigate development of temperature with various pyro start pressure. Computations have been carried out several turbine rotational speeds in the range from 0 to 16000 rpm and inlet conditions with 1423K, 7.2MPa. As a result, the more rotational speed and pyro starter pressure of turbine increased, the more turbine blade's temperature decreased. It is also found that flow field of turbine blade inlet area at pyro starter pressure of 5.75MPa and rotational speed of 12100 rpm formed surface temperature uniformly.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.2
• /
• pp.43-49
• /
• 2001

In order to satisfy the ULEV emissions regulation, fast light-off of a catalyst is essential for reduction of HC and CO emissions during the cold start. Cranking Exhaust Gas Ignition(CEGI) method developed in this study showed that the catalyst reaches the light-off temperature in a few seconds. The CEGI stops the ignition signal for a few seconds during the cranking period, so the unburned fuel-air mixture bypasses the combustion chamber and flows through the exhaust manifold. When the unburned mixture reaches two glow plugs installed upstream of the catalyst, it burns and releases the thermal energy to heat up the catalyst, In the FTP-75 vehicle tests, the CEGI showed that the exhaust emissions reduced by 47.7% for THC and by 88.6% for CO in the cold-transient phase of the test.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.12 no.1
• /
• pp.93-100
• /
• 2017

Four-stroke cycles in an automobile engine are suction stroke, compression stroke, combustion stroke and exhaustion stroke. A normal operation of engine in compression and power stroke must be processed in optimal fuel-air pressure. In this paper we describe a development of measuring equipment for engine cylinder pressure with observing supply current to self motor(start motor). By comparing the current wave on pressure of the 4 or 6 cylinder in engine, a abnormal cylinder state will be found. The validity of the proposed measuring equipment was shown by experiment for real automobile.

• Journal of IKEEE
• /
• v.18 no.1
• /
• pp.152-158
• /
• 2014

It is very important to supply the diesel fuel from fuel tank to combustion chamber in case of cold start procedure. the paraffin hydrocarbons are easily solidified at low fuel temperature and it can be blocking the fuel supply to the high pressure fuel pump. In order to reduce the fuel crystallization (Waxing), it have been used to develop not only cold flow additives but also the proper mounting design of fuel filter. Block heater in the fuel filter assembly have been also contained to improve the cold start and prevent blocking the fuel supply in Common Rail Direct Injection System. we can obtain the fuel pressure drop and fuel flow rate, power consumption of fuel heater to have the cold flow evaluation test with the saperated and composited fuel heater at the low ambient temperature, Due to evaluating cold flow performance of two block heater, we knew that composited package fuel heater was the excellent cold flow performance compared to separated type and obtained the parameters of cold flow.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.05a
• /
• pp.181-189
• /
• 2010

개방형 액체로켓엔진 시스템에 대한 동특성 예측 프로그램을 작성하였다. 이 프로그램을 통해 얻은 펌프 시동 시 시간에 따른 압력 및 유량 변화 결과를 수류실험장치를 구축하여 실험적으로 검증하였다. 수류실험장치는 실제 액체로켓엔진 추진제 공급 계통에서 구성품의 형태와 배치위치, 가스발생기와 주연소실로 분기되는 유량비를 기준으로 모사되었다. 측정 시 관로가 채워진 상태에서 펌프를 시동하였으며 펌프는 전동기로 구동된다. 동특성 예측 프로그램의 작성을 위해 구성품별 동특성 모델링을 수행하고 엔진 시스템을 기준으로 각 모델링을 순차적으로 통합하였다. 구성품의 동특성 파라미터를 측정 반영하였고 압력 밸런싱을 통해 수렴 조건이 결정된다. 수렴된 밀도와 유량을 가지고 다음 시간에서의 초기 입력 값으로 대체하여 계산을 수행하였다. 천이 작동 상태에서 엔진 시스템 내의 물리량 변화를 전산 예측과 더불어 실험적으로 측정하고 비교하였다.

• Journal of IKEEE
• /
• v.17 no.1
• /
• pp.63-70
• /
• 2013

In this paper, we have implemented the performance evaluation system of the unified fuel heater for CRDI diesel engine. If the diesel engine be cold by low temperature in winter, then that makes the waxing materials like a paraffin and is the source of poor engine starting. The unified fuel heater is the barrow meter that estimate the start performance of diesel engine, and be tested by test chamber. The chamber perform the normal temperature, an extremely low temperature, an operating performance in an extremely high temperature, the resistance operation delay time and current operation delay time in setting up test resistance, the bimetal delay time test in temperature variation, the current and resistor test of the composited heater, a heating operation test.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.5
• /
• pp.2375-2380
• /
• 2013

In this paper, we have implemented the unified fuel heater and performance evaluation system for diesel cars. In order to strengthen an engine starting of diesel car, we need to assembly the fuel filter and heater. Especially, this assembly fuel heater is very important in winter, it is necessary for heating to operate the diesel engine. The heater for unifying the sensor and heater body can advance the performance of car and reduce the production cost. Finally, the performance test chamber is needed to evaluate the performance of heater.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.213-217
• /
• 2017

Since more than 30% of the liquid rocket engine failures occur during the start-up process, and the Space Shuttle Main Engine (SSME) is especially sensitive to small changes in propellant conditions, a 2% error in the valve position or a 0.1sec timing error could lead to significant damage of the engine, simulation modeling of start-up process is important. However, there are many difficulties associated with engine start-up process caused by nonlinear mass flow and heat transfer characteristics associated with filling an unconditioned engine system with cryogenic propellants. In this paper, we modelled a SSME simulation model using partially Computational Fluid Dynamics (CFD) method to solve these problems and checked the performance by comparing with the performance of the simulation model using the lumped method under the state of normal condition.

• Proceedings of the KIEE Conference
• /
• 2000.11c
• /
• pp.556-558
• /
• 2000

유한요소법을 이용하여 대전력용 트리가트론의 전극 전압의 극성 변화와 전극 구조의 변화에 따른 전계 분포를 해석하였다. 시동 특성을 좋게 하기 위해서는 트리거 전극과 접지 전극 사이의 적절한 거리를 찾아야 한다. 유한요소법을 이용한 전계 분포를 가지고 이 거리를 정할 수 있다. 본 논문은 트리거 갭과 주 갭(트리거 전극과 반대 주전극 사이)에서 동시에 절연 파괴가 일어날 때 트리가트론이 최적으로 동작한다는 연구 결과를 바탕으로 한다. 본 논문은 실험을 위한 예비 단계로서, 시뮬레이션을 통하여 최적의 전극 구조를 찾는데 드는 비용과 시간을 줄일 수 있다.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.44.2-44.2
• /
• 2011

고분자 전해질 연료전지는 다른 연료전지에 비해 작동온도가 낮고 전류밀도 및 출력밀도가 높으며 시동시간이 짧아서 다양한 분야에 응용이 가능할 것으로 기대된다. 그 중 양극판은 가격비와 중량비가 높아 부품 가격 및 중량을 낮출 경우 파급 효과가 높은 것으로 예상된다. 본 연구에서는 일반적으로 사용하고 있는 스테인리스강보다 가격이 저렴한 저탄소강을 모재로 이용하였다. 저탄소강은 자체로 내식성을 가지지 못하므로, 최근에 차세대 신소재로 각광을 받고 있는 그라핀(graphene)을 전기분무(electro spray coating)법으로 코팅하여 저탄소강의 내식성을 향상시키고자 하였다. 그라핀은 에탄올을 용매로 사용하여 분산하였으며, 분산제로 소량의 다이페닐다이에톡시실란(diphenyldiethoxysilane)을 첨가하여 코팅용액을 제작하였다. 코팅공정은 5~15 kV의 전압을 가하여 1시간동안 코팅을 진행하였으며, 그라핀-저탄소강의 미세구조를 주사전자현미경과 광학현미경을 통하여 관찰하였다. 또한 X-선 회절분석법을 이용하여 그라핀의 결정구조를 분석하였다. 한편 스택의 내부와 유사한 산화성 분위기를 모사하기 위해 $80^{\circ}C$의 0.1N $H_2SO_4$+2ppm $F^-$ 용액에서 내식성 실험을 수행하였고 면간접촉저항을 측정하였다. 그라핀이 코팅된 저탄소강 시편은 고분자 전해질 연료전지 양극판의 요구조건을 만족하였으며, 연료전지 양극판으로서의 사용가능성을 확인하였다.