• 대한기계학회논문집A
• /
• 제26권12호
• /
• pp.2605-2614
• /
• 2002

This paper describes an analysis method based on the experimental parameter for the 0.9kW starter motor of vehicle with permanent magnet and pole core, and analyzed the influence by the effect of pole core of starting motor by using the 2D-FEM analysis technique to reflect the structural characteristic of 3D. A starter motor consists mainly of armature, yoke and permanent magnet with the pole core. Additionally, there is different the axial length of each part. Therefore, the effective of analysis method is needed to improve the characteristic of it. This paper approached the 2D-FEM analysis estimated by the 3D-EMCN(Three Dimensional Equivalent Magnetic Circuit Network) instead of the 3D-FEM analysis to minimize parameters. As a result, this paper is proposed the validity of 2D-FEM analysis and obtained reasonable results for improving a performance.

• Tribology and Lubricants
• /
• 제31권3호
• /
• pp.125-140
• /
• 2015

In this paper, we present the results of the wear analysis of journal bearings on a stripped-down single-cylinder engine during start-up and coast-down by motoring. We calculate journal bearing wear by using a modified specific wear rate considering the fractional film defect coefficient and load-sharing ratio for the asperity portion of a mixed elastohydrodynamic lubrication (EHL) regime coupled with previously presented graphical data of experimental lifetime linear wear in radial journal bearings. Based on the calculated wear depth, we obtain a new oil film thickness for every crank angle. By examination of the oil film thickness, we determine whether the oil film thickness at the wear scar region is in a mixed lubrication regime by comparing dimensionless oil film thickness, h/σ, to 3.0 at every crank angle. We present the lift-off speed and the crank angles involved with the wear calculation for bearings #1 and #2. The dimensionless oil film thickness, h/σ, illustrates whether the lubrication region between the two surfaces is still within the bounds of the mixed lubrication regime after scarring of the surface by wear. In addition, we present in tables the asperity contact pressure, the real minimum film thickness at the wear scar region, the modified specific wear rate, and the wear angle, α, for bearings #1 & #2. To show the real shape of the oil film at wear scar region, we depict the actual oil film thickness in graphs. We also tabulated the ranges of bearing angles related with wear scar. We present the wear volume for bearings #1 and #2 after one turn-on and turn-off of the engine ignition switch for five kinds of equivalent surface roughness. We show that the accumulated wear volume after a single turn-on and turn-off of an ignition switch normally increases with increasing surface roughness, with a few exceptions.

• Tribology and Lubricants
• /
• 제31권3호
• /
• pp.109-124
• /
• 2015

This paper presents a wear analysis procedure for the journal bearings on a stripped-down single-cylinder engine during start-up and coast-down by motoring. A journal bearing is in the mixed elastohydrodynamic (EHL) lubrication region when the shaft speed is less than the corresponding lift-off speed. Below the lift-off speed, a wear scar can form on bearing surfaces. In part 1 of this paper, we develop the appropriate formulations and the calculation procedure for the analysis. Specifically, we formulate an equation for modified film thickness in a journal bearing considering the additional wear volume. In order to obtain the modified specific wear rate induced by the modified Archard’s wear coefficient, we utilized the extended non-dimensional diagram for the specific wear rate, k, the fractional film defect coefficient, Ψ and the asperity load sharing factor, γ₂. This asperity load sharing factor is newly calculated by setting the Zhao-Maietta-Chang (ZMC) asperity contact pressure equation coupled with the central film thickness equation derived by using the ZMC asperity contact model equal to the modified central contact pressure derived by using the central (or maximum) contact pressure at the dry rough line-contact configuration. We can use the procedure introduced in this paper to determine the lifetime (or longterm) linear wear in radial journal bearings that is a result of repeated stop-start cycles.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2008년도 춘계학술대회 논문집
• /
• pp.689-690
• /
• 2008

• 한국추진공학회지
• /
• 제16권5호
• /
• pp.97-107
• /
• 2012

일반적으로 고체 추진기관은 큰 비추력과 재시동 능력을 갖고 있는 액체 추진기관에 비하여 경비 면에서 효과적이고 큰 추력 능력을 갖고 있다. 이러한 이유로 고체 추진기관은 주로 부스터나 1단 추진기관으로 많이 사용되고 있다. BBL 접근 방법이 저 비용과 제한된 개발기간 그리고 낮은 위험성을 고려하여 연구되어 오고 있다. 탄소 섬유 에폭시 레진의 모터 케이스 사용이 확대되고 있고 특히 비활성 질량 감소로 고 강도 탄소섬유가 관심을 끌게 될 것이다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2008년도 춘계학술대회논문집
• /
• pp.869-873
• /
• 2008

Optimization method for the open loop commutation time intervals in HDD spindle start-up control is presented in this paper. A hard disk drive(HDD) uses a sensorless brushless DC motor(BLDC) for the platter rotation. Because there is no direct sensor for the rotor position, open loop commutations after sensing the rotor position at a standstill using inductive sensing method are performed to speed up the rotor up to a certain speed where the zero crossings of the back electromotive force(EMF) are measurable. Therefore successful open loop commutations are necessary for the stable start-up control of the spindle motors. Random neighborhood search(RNS) algorithm is introduced as a optimization technic in this paper. Rotor speed and its standard deviation are used as a cost function and commutation intervals obtained from the spindle motion equation are used as initial parameter values for the RNS. With the help of the proposed method optimized open loop commutation time intervals for the very low start-up current are acquired and tested. The experimental results shows that the proposed method can decrease the start-up failure rate of a HDD spindle motor.

• Tribology and Lubricants
• /
• 제33권4호
• /
• pp.168-186
• /
• 2017

This paper presents a wear analysis procedure for calculating the wear of journal bearings during the start-up and coast-down cycles of a motoring stripped-down single cylinder engine operating with a tilted shaft. In order to decide whether the lubrication state of a journal bearing is in the mixed-elasto-hydrodynamic lubrication regime, we utilize lift-off speed and MOFT (most oil film thickness) under mixed-elasto-hydrodynamic lubrication regime at the corresponding aligned shaft. We formulate an equation for the modified film thickness in a misaligned journal bearing considering the additional wear volume described in Part I of this study. For this, we use the calculation results of the degree of misalignment and tilting angle obtained after finding the eccentricities of the two bearings supporting the crankshaft of a single cylinder engine. In this Part II, we calculate the wear of journal bearings using the fractional film defect coefficient, the asperity load sharing factor, and the modified specific wear rate for the application of mixed-elasto-hydrodynamic lubrication regime. We show that the accumulated wear volume after turning the ignition switch on and off once, increases to ${\sigma}=39{\mu}m$ and then decreases from ${\sigma}=39{\mu}m$ with increasing in surface roughness.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.3323-3328
• /
• 2007

Conventional LPG pump for Liquified Petroleum injection(LPi) engine has been adopted vane type. But the BLDC type fuel pump for LPi system has complicated structure and its price is high. Therefore, as a alternative, this study has mainly focused on the development of turbine type LPG pump which has lower cost and simple structure than conventional BLDC type. To verify the possibility of substitute the performance tests were performed for each fuel pump. The comparative items were pressure settling time, variation of fuel outlet temperature and engine performance of hot restart ability. As a result, performances of turbine type LPG pump were equivalent or high comparing to the BLDC type all over the tests for different fuel composition.

• 물과 미래
• /
• 제12권2호
• /
• pp.49-55
• /
• 1979

본 연구는 관수로내의 부정류 즉 펌푸모터의 시동, 정지 및 발브 조절시에 압력관수로에 나타나는 급변류의 현상, 특히 수격작용의 해석을 Computer에 의해 자동해석하는 방법을 강구하였다. 따라서 사용되는 관수로가 펌푸, 관망, 터널, 조압수조, 분기관, 저수지, 폐단관 및 발브장치를 갖는 일련의 관수로내에 일어나서 전자계산기를 사용하면 송수 또는 배수관로 설계에 있어 설계자의 시간과 노력을 감소하고 정확한 결과를 얻을 수 있는 장점이 있다.

• Tribology and Lubricants
• /
• 제33권4호
• /
• pp.153-167
• /
• 2017

The aim of this study is to find the change in trend in the eccentricities of two journal bearings supporting the crankshaft of a single cylinder engine and the degree of misalignment of the shaft. We analyze the change in oil film thickness considering the wear scar under mixed-elasto-hydrodynamic lubrication regime at potential wear regions. For this, we first calculate the central eccentricities of the two journal bearings by using the mobility method. Then we calculate the outer end eccentricity by using the geometry of the bearings. Further, the tilting angle and degree of misalignment of the shaft are calculated by using the eccentricities of the two bearings. We show that the eccentricity of bearing #1, on which higher load is applied, increases at the beginning of the start-up cycle and during the coast-down cycle. However, the eccentricity of bearing #2, on which lower load is applied, decreases at the beginning of the start-up cycle and increases during the coast-down cycle. From the results of the analysis of oil film thickness, we show that the mixed-elasto-hydrodynamic lubrication regime for a misaligned shaft is at the initial stages of the start-up cycle for both bearing #1 and #2 and at the final stage of the coast-down cycle for only bearing #1.