• Korean Journal of Food Science and Technology
• /
• v.47 no.5
• /
• pp.586-592
• /
• 2015

This study was performed to determine optimum approaches for control of microorganisms in school refectories and kitchens. A reduction of more than 5.0 log CFU/mL was noted for Escherichia coli O157:H7, Salmonella Typhimurium, Listeria monocytogenes, Staphylococcus aureus, and Streptococcus mutans after treatment with 5 ppm ozone water for 60 s. Treatment of different vegetables with ozone water for 5 min showed bactericidal effects with 2-4 log reduction of viable cell number; the bactericidal effects differed according to the kinds of vegetables. The viable cell number on kitchen apparatus and tableware was not detected by ozone water treatment for 60 s. In addition, the count of the bacteria floating in the air in refectories and kitchens decreased 2.0 log CFU/1,000 L air to 0-1 CFU/1,000 L air on treatment with 45 ppm ozone gas for 12 hr. Therefore, ozone water and ozone gas may be good candidates as antimicrobial agents that can be used to improve sanitary conditions in school refectories and kitchens.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.26 no.2
• /
• pp.163-174
• /
• 2020

Particulate matter levels are rapidly increasing daily, and this can affect human health. Therefore, air pollutant emissions from sea vessels require management. This study evaluates the status of air pollutants, focusing on air pollutant emissions from the vessels of the Korea Coast Guard (KCG), and proposes national management measures to reduce emissions. According to a report recently released (2018) by the National Institute of Environmental Research (NIER), emissions from vessels constituted 6.4 % of the total domestic emissions, including 13.1 % NO_x, 10.9 % SO_x, and 9.6 % particulate matter (PM10/PM2.5). Among the rates of pollutant emission from vessels, the emission rates of domestic and overseas cargo vessels were the highest (50.6 %); the ratio of fishing boats was 42.6 %. With respect to jurisdictional sea area, 44.1 % of the emissions are from the south sea, including the Busan and Ulsan ports, and 24.8 % of the emissions are from the west sea, including the Gwangyang and Yeosu ports. The KCG inspects boarding lines to manage emission conditions and regulate air pollutant emissions, but it takes time and effort to operate various discharge devices and measure fuel oil standards. In addition, owing to busy ship schedules, inspection documents are limited in terms of management. Therefore, to reduce the air pollutant emissions of such vessels, regulations will be strengthened to check for air pollutants, and a monitoring system based on actual field data using KCG patrol ships will be established, for each sea area, to manage the emissions of such vessels. Furthermore, there is a need for technological development and institutional support for the introduction of environmentally friendly vessels.

• Cartoon and Animation Studies
• /
• s.44
• /
• pp.1-31
• /
• 2016

In this thesis, the movie with mise-en-scene established was compared with the peculiarity of the play that is the etymological source of the term to identify the peculiarity of mise-en-scene which was substituted into animation to find the peculiarity of mise-en-scene in animation. To emphasize the direct connection between the frame's visual peculiarity and the director's opinions, the mise-en-scene of director centered animation created under a restricted environment was reviewed. Mise-en-scene which started from movie critics theory does not simply mean the arrangement of images in a frame. Mise-en-scene emphasizes the exposure of the work's motive by the visual components. The animation's assuming the middle point of environmental share possessed by play and movie when schematizing the genre peculiarity of animation, play and movie was a noteworthy result. It can be said that the cause is that the animation's peculiarity yield different results depending on the making methods; we verified that this is a key factor in the analysis of animation's mise-en-scene. I emphasized that the peculiarity of animation mise-en-scene is in its making method and material and suggested identifying the work's making methods and analyzing the work's aesthetic results derived in this way. The russian animation which was perceived as peripheral arts was relatively free from the burden of censorship while receiving support from the Soviet as a media for propaganda. The russian animation's mise-en-scene which found the material for its works in the country's folklore was metaphorical, focused on new expression forms and achieved experimental elements. Russian animation pursues a unique aesthetic world through space expression based on the forms of opera or ballet and heavy motions formed static inbetweens.

• Journal of Korean Ophthalmic Optics Society
• /
• v.13 no.1
• /
• pp.53-58
• /
• 2008

Purpose: To design and fabricate the small sputter coating system for the Ophthalmic lens. Methods: The design of sputter target was done using macleod program for AR coating and mirror coating of Ophthalmic lens with Si target and then the sputter system was fabricated. Results: The optimum condition of AR coating with Si target was [air|$SiO_2$(81.3)|$Si_3N_4$ (102)|$SiO_2$(19.21)|$Si_3N_4$(15.95)|$SiO_2$(102)|glass], for blue color mirror coating [air|$SiO_2$(56.61)|$Si_3N_4$(135.86)|$SiO_2$(67.64)|$Si_3N_4$(55.4)|$SiO_2$(53.53)|$Si_3N_4$(51.28)|glass], for green color coating [air|$SiO_2$(66.2)|$Si_3N_4$(22.76)|$SiO_2$(56.58)|$Si_3N_4$(140.35)|$SiO_2$(152.35)|$Si_3N_4$(70.16)|$SiO_2$(121.87)|glass], for gold color [air|$SiO_2$(83.59)|$Si_3N_4$(144.86)|$SiO_2$(11.82)|$Si_3N_4$(129.93)|$SiO_2$(90.01)|$Si_3N_4$(88.37)|glass]. Conclusions: In the fabrication of sputtering coating apparatus, Dual cathode with same Ti target were coated at the same time on both sides of Ophthalmic lens to lessen the time of coating on Ophthalmic Lens and save the cost of the lens. The distance of target-substrate of cathode was variable from 12.5 cm to 20 cm. Turbo pump was used to take the whole coating process about 15 min. instead of diffusion pump. The lens holder was made to coat 2 pairs lens every coating and was rotated to get the uniformity of thin film.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.17 no.1
• /
• pp.27-38
• /
• 2009

To investigate the feasibility of refuse derived fuels (RDFs) combined of sewage sludge and combustible wastes such as substitutive fuels instead of a stone coal, several different RDFs made with different mixtures of sewage sludge and combustible wastes were analyzed by various experiments. The combustion characteristics for the RDFs were investigated by analyzing fuel gases, and heating values were also measured by a bomb calorimeter. The fundamental properties such as moisture contents, ratios of combustible materials, amounts of ashes, heavy metals, ratios of each chemical elements and heating values were analyzed in accordance with mixing ratios of wt(%) for researching the characteristics of the RDFs. $RDF_{k-1}$ was made of mixing materials which were dried sewage sludge, food wastes and combustible wastes. $RDF_{k-2}$ was made of mixing materials which were peat-moss, tar and sewage sludge. Combustion experiments were carried out at the optimal conditions which were m=2 under air-fuel condition and $850^{\circ}C$. The retention times in the combustor were set at 5, 10 and 15minutes. 50 g of RDFs was put in the combustor for each experiments. The ranges for heating values of $RDF_{k-1}$ with different mixing ratios were from 6,900 kcal/kg to 8120 kcal/kg. The ranges for heating values of $RDF_{k-2}$ with different mixing ratios were from 4,014 kcal/kg to 8,050 kcal/kg. As a result of this study, the heating values, moisture contents, components of chemical elements and mixing ratios of the materials in RDFs had big effects on the efficiency of the combustion. In $RDF_{k-1}$, the higher amounts of combustible wastes in the mixtures, the higher heating values, concentrations of $C_xH_y$ and amounts of ashes were produced. In $RDF_{k-2}$, the higher tar amounts in the mixtures caused the higher heating values, amounts of ashes, concentrations of CO gas and CxHy.

• The Journal of Korean Society for Radiation Therapy
• /
• v.19 no.1
• /
• pp.27-33
• /
• 2007

Purpose: We have performed SRS (stereotactic radiosurgery) for avm (arterry vein malformation) and brain cancer. In order to verify dose and localization of SRS, dose distributions from TPS ($X-Knife^{(R)}$ 3.0, Radionics, USA) and GafChromic $EBT^{(R)}$ film in a head phantom were compared. Materials and Methods: In this study, head and neck region of conventional humanoid phantom was modified by substituting one of 2.5 cm slap with five 0.5 cm acrylic plates to stack the GafChromic $EBT^{(R)}$ film slice by slice with 5 mm intervals. Four films and five acrylic plates were cut along the contour of head phantom in axial plane. The head phantom was fixed with SRS head ring and adapted SRS localizer as same as real SRS procedure. CT images of the head phantom were acquired in 5 mm slice intervals as film interval. Five arc 6 MV photon beams using the SRS cone with 2 cm diameter were delivered 300 cGy to the target in the phantom. Ten small pieces of the film were exposed to 0, 50, 100, 200, 300, 400, 500, 600, 700, 800, 900 cGy, respectively to calibrate the GafChromic $EBT^{(R)}$ film. The films in the phantom were digitized after 24 hours and its linearity was calibrated. The pixel values of the film were converted to the dose and compared with the dose distribution from the TPS calculation. Results: Calibration curve for the GafChromic $EBT^{(R)}$ film was linear up to 900 cGy. The R2 value was better than 0.992. Discrepancy between calculated from $X-Knife^{(R)}$ 3.0 and measured dose distributions with the film was less than 5% through all slices. Conclusion: It was possible to evaluate every slice of humanoid phantom by stacking the GafChromic EBT film which is suitable for 2 dimensional dosimetry, It was found that film dosimetry using the GafChromic $EBT^{(R)}$ film is feasible for routine dosimetric QA of stereotactic radiosurgery.

• The Journal of Korean Society for Radiation Therapy
• /
• v.19 no.2
• /
• pp.91-97
• /
• 2007

Purpose: To evaluate the feasibility of a commercial ion chamber array for intensity modulated radiation therapy (IMRT) quality assurance (QA) was performed IMRT patient-specific QA Materials and Methods: A use of IMRT patient-specific QA was examined for nasopharyngeal patient by using 6MV photon beams. The MatriXX (Wellhofer Dosimetrie, Germany) was used for IMRT QA. The case of nasopharyngeal cancer was performed inverse treatment planning. A hybrid dose distribution made on the CT data of MatriXX and solid phantom all of the same gantry angle (0$^\circ$). The measurement was acquired with geometrical condition that equal to hybrid treatment planning. The $\gamma$-index (dose difference 3%, DTA 3 mm) histogram was used for quantitative analysis of dose discrepancies. An absolute dose was compared at the high dose low gradient region. Results: The dose distribution was shown a good agreement by gamma evaluation. A proportion of acceptance criteria was 95.8%, 97.52%, 96.28%, 98.20%, 97.78%, 96.64% and 92.70% for gantry angles were 0$^\circ$, 55$^\circ$, 110$^\circ$, 140$^\circ$, 220$^\circ$, 250$^\circ$ and 305$^\circ$, respectively. The absolute dose in high dose low gradient region was shown reasonable agreement with the RTP calculation within $\pm$3%. Conclusion: The MatriXX offers the dosimetric characteristics required for performing both relative and absolute measurements. If MatriXX use in the clinic, it could be simplified and reduced the IMRT patient-specific QA workload. Therefore, the MatriXX is evaluated as a reliable and convenient dosimeter for IMRT patient-specific QA.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.26 no.4
• /
• pp.380-391
• /
• 1993

The experimental study was made to propose the treatment method of wastewater in the high-density fish culture system. The BOD to COD ratios of effluents were almost same to 0.65 in the eel-farm, but were various in the farm rearing together with tilapia etc. A BOD rate curve of the eel-farm effluent could be described mathematically by the equation, $BODu=14.1(1-10^{-0.222t})+30.9(1-10^{-0.035(t-8)})$. Nitrification in Biological Fluidized Bed(BFB) system to treat the fish-farm wastewater could be reduce ammonium level up to $65{\sim}79\%$ when ammonium loading rates were between 0.014 and 0.075g $NH_4/g$ BVS-day. Nitrification efficiency was decreased by organic matters in the wastewater when ammonium loading was low(0.014 g $NH_4/g$ BVS-day). T-N removal ratios were decreased to increase loading in denitrification process, because of low C/N ratio. Based on much higher biological mass concentrations, BFB system takes many advantages of a practical viewpoint, such as stability of treatment efficiency and reduction of necessary site area for the facility, as compared with conventional treatment systems.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.35 no.1
• /
• pp.35-45
• /
• 2002

Seasonal quantitative van Veen grab sampling was conducted to characterize the composition and structure of the benthic polychaete community inhabiting the shellfish farming ground of a coastal bay system of Jiniu Bay (Korea). A total of 132 polychaete species were identified and the polychaetes accounted for about $80\%$ of overall abundance of benthic animals. There was little significant seasonal difference in densities (abundances) of polychaetes, Maximum biomass was obseued in summer (August) and minimum value was recorded in winter (February) and spring (May). Conversely, diversity and richness were lowest in summer, indicating a seasonal variability in the polychaetous community structure, The cluster analysis indicated that such a seasonal variability resulted mainly from the appearance of a few small, r-selected opportunists in spring and the tubiculous species of the family Maldanidae in summer. On the other hand, several indicator species for the organically enriched environments such as Capitelia capitata, Notoniashs Jatericeus and hmbrineris sp. showed high densities during all the study period. Density and biomass of univariate measures of community structure were significantly lower in the arkshell-farming ground of the southern area than in the non-farming sites of the bay, A similar general tendency was also found in the spatial distributions of species diversity and richness. Principal component analysis revealed the existence of different groups of benthic assemblages between the arkshell-farming ground and non-farming sites, The lack of colonization of r-selected opportunists and/or tubiculous species in the former ground seemed to contribute to the spatial differences in the composition and structure of the polychaetous communities. Although finer granulometric composition and high sulfide concentration in sediments of the arkshell-farming ground and low salinity in the northern area were likely to account for parts of the differences, other environmental variables observed were unlikely. The spatial distribution of polychaetes in Jiniu Bay may be rather closely related to the sedimentary disturbance by selection of shells for harvesting in spring.

• Cartoon and Animation Studies
• /
• s.47
• /
• pp.31-52
• /
• 2017

NCS education was created to realize a society in which skills and abilities are respected, such as transcending specifications, establishing recruitment systems, and developing and disseminating national incompetence standards. At the university level, special lectures and job training are being strengthened to raise industrial experts. Especially, in the field of animation, new technologies are rapidly emerging and demanding convergent talents with various fields. In order to meet these social demands, there is a limit to the existing one-class teaching method. In order to solve this problem, it is necessary to participate in a variety of specialized teachers. In other words, rather than solving problems of students' job training and job creation, It is aimed to solve jointly, Team teaching was suggested as a method for this. The expected effects that can be obtained through this are as follows. First, the field of animation is becoming more diverse and complex. The ability to use NCS job-related skills pools can be matched with professors from other departments to enable a wider range of professional instruction. Second, it is possible to use partial professorships in other departments by actively utilizing professors in the university. This leads to the strengthening of the capacity of teachers in universities. Third, it is possible to build a broader and more integrated educational system through cooperative teaching of professors in other departments. Finally, the advantages of special lectures and mentor support of college professors' pools are broader than those of field specialists. A variety of guidance for students can be made with responsible professors. In other words, time and space constraints can be avoided because the mentor is easily met and guided by the university.