• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.3 no.3
• /
• pp.533-540
• /
• 1999

In this paper, a microstrip antenna is designed using a rectangular patch. To find characteristics of the antenna, computer simulations of the rectangular single microstrip patch antenna are performed with changing width and feed line. And we found characteristics of RHCP using axial ratio. Through the results, we found that the Finite Difference Time Domain(FDTD) method is an effective method for designing microstrip patch antenna. According to simulation the resonant point has been found it in the frequency received from GPS satellite. And these results were in relatively good accordance with the measured values.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.48 no.11
• /
• pp.83-88
• /
• 2011

The spectral field data on the observation planes inside a mode stirred chamber have been computed by using the FDTD method. They can describe the directional dependence of all supported modes in the reverberation chamber (RC). Correlation coefficients have been found to evaluate the stirring effects. The correlation coefficients were obtained and compared for three different sizes of stirrers and statistical uniformity was investigated.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.8
• /
• pp.1997-2004
• /
• 1994

A model analysis method has been developed in the paper. The method estimates the modal parameters of multiple input-output systems, assesses their quality, and seperates structural modes form computation ones. The modal parameter extraction algorithm is the least squares method with a finite difference model relating input and output time data. The quality of the estimated system model can be assessed in narrow frequency bands by comparing the measured and model predicted responses in time domain with the aid of digital filters. Structural modes can be effectively separated from computational ones using the convergence factor which represents the pole convergence rate. The modal analysis method has been applied to simulated and experimental vibration data to evaluate its utility and limitations.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.4
• /
• pp.29-40
• /
• 2004

This paper reports the frequency characteristics and the time response of parallel adjacent-transmission lines, crossed adjacent-transmission lines and parallel adjacent-transmission lines which are on the different planes by using FDTD-PML method. In the parallel adjacent-transmission lines, the crosstalks as a function of horizontal distance are calculated and in the crossed adjacent- transmission lines, the crosstalks as a function of vertical distance are simulated. Also, the crosstalks as functions of horizontal and vertical distances are measured and analyzed in the parallel adjacent-transmission lines which are on the different planes.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.5
• /
• pp.479-488
• /
• 2003

Dual-band microstrip antenna is designed for industrial-scientific-medical(ISM) band of 2.4 GHz and 5.8 GHz using finite-difference time-domain method(FDTD). Cross patch 130 by aperture in the ground plane of microstrip line is proposed as radiation element of antenna which is 2 rectangular patch is overlapped. To design antenna, change of input impedance is examined by length change of aperture and stub. And center frequency and - 10 dB bandwidth are investigated by change of length and width in radiation element. Measured result about reflection loss confirm that agree well with simulation results of FDTD and IE3D. And 3 dB beam width, front to back ratio and maximum gain is presented by measuring radiation pattern of antenna in frequency 2.43 GHz and 5.79 GHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.2
• /
• pp.206-216
• /
• 2000

In this paper, the linear tapered slot(LTS) antenna and linear constant tapered slot(LCTS) antenna are optimized for millimeter-wave antenna by the finite difference time domain(FDTD) method and then fabricated and measured. The microstrip-to-slot transition is proposed with the widen $\lambda$/4 open stub as feeder for wide bandwidth of 16.5GHz($VSWR\leq2$). The results of the calculation and measurement, the bandwidth of LTS antanna is 8.3GHz(26.47%) and 7.1792GHz(22.4%) respectively. Also, the bandwidth of LCTS antenna is 8.1GHz(26.47%) and 6.3243GHz(20.43%) respectively.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.42 no.12
• /
• pp.159-164
• /
• 2005

Recently, it has demanded high-speed digital circuits as information increase. Therefore, electromagnetic characteristics of compact microwave circuit occurred importantly. And, the effect of the imperfect ground plane on the signal integrity and influence of coupling between two parallel lines for high-speed digital transmission line on the printed circuit board is investigated by FDTD simulations in 3-D electromagnetic analysis method. The results of FDTD simulation are compared with the ADS simulation in commercial software, analyzed lumped element of modeling and electromagnetic wave's radiation of slot as frequency. As a consequence, when the slot in the ground plane is under microstrip line, it has much effect on propagation of wave.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.11 s.114
• /
• pp.1096-1104
• /
• 2006

In this paper, the broadband antenna for the combined base station of Cellular/PCS/IMT-2000/Wibro and S-DMB services is designed and the proposed antenna allows having sufficient coverage for each service band. In order to get the broadband impedance matching, the tapered sections are applied on the both terminus of hi-conical respectively. The design parameter is calculated and simulated by using FDTD method. As a result, the measured bandwidth of the proposed antenna is $0.79GHz{\sim}2.93GHz$ and the gain is distributed from 5.5 dBi up to 8.19 dBi.

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.6 no.1
• /
• pp.48-65
• /
• 1995

This paper deals with the analysis of the unintentional radiation from the TDX-1B subscriber Board. According to the demand of digital systems and developement of high speed switching devices, electro- magnetic noise intensity and it's bandwidth occupancy in spectrum are increasing and so there is a serious possibility causing the various EMI phenomena. More accurate radiation model was established by using the Finite Difference Time Domain (FDTD) analysis, and the EMI probabilistic analysis of the digital switching system was performed. For validating the proposed model and its calculated results, on-promises test was performed and compared with the calculated results. These results may be applicable to be used for EMI model in large digital system, and prediction of EMI effect from a large digital system, and the EMI control design when designing digital system to meet inter- national EMI regulation.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.37 no.6
• /
• pp.36-43
• /
• 2000

Three-Dimensional FDTD method is applied to analyze the dielectric resonator coupled with two microstrip lines. We model accurately the curved surface using Noriaki model. The frequency resolution is 106.46 MHz by the conventional FFT However it is not sufficient for determining its resonant frequency. So we introduce the Pad approximation and Stoer-Bulirsch method in order to have the high frequency resolution degree, 1.00 MHz. All results are compared with the measured data. As a result, we acquire the very precise result through the Pad approximation. And sinusoidal wave is applied. From the plot of the electric and magnetic field distribution, it is shown that the resonant mode is TE$_{01{\delta}}$ mode.