• Applied Chemistry for Engineering
• /
• v.19 no.5
• /
• pp.568-573
• /
• 2008

Kinetic tests on pyrolysis of waste fishing net [WFN; nylon-6], waste ship lubricating oil [WSLO] and their mixture were carried out by thermogravimetric analysis (TGA) with heating rate of 0.5, 1.0, and $2.0^{\circ}C/min$. Pyrolysis of waste fishing net started at $300^{\circ}C$, and the main region of decomposition temperature was between 360 and $440^{\circ}C$ at each heating rate. Decomposition temperature of the mixture of WFN and WSLO was lower than that of WFN and WSLO, and the shape of thermogravimetic graph of mixture was different as well. The corresponding kinetic parameters including activation energy and pre-exponential factor were determined by differential method over the degree of conversions. The values of activation energies for the mixture of WFN and WSLO were between 98 and 427 kJ/mol as the conversion increased from 5% to 95%. Tubing reactor was used to analysis of pyrolyzed oil at $440^{\circ}C$ for 80 min. The selectivity of specific hydrocarbons was not detected and the carbon number distribution of the pyrolyzed oil was below $C_{22}$.

• Polymer(Korea)
• /
• v.25 no.4
• /
• pp.575-586
• /
• 2001

Stabilized polyacrylonitrile (PAN) fibers can be transformed into quasi-carbon fibers with different properties depending on heat-treatment processing parameters at lower temperatures than temperature for the fabrication of carbon fibers. It has been investigated from the preliminary work that appropriate quasi-carbonization processes at about 1100$^{\circ}C$ strongly influence various properties of quasi-carbon fiber/polymer composite as well as quasi-carbon fiber itself. The objective of the present work is to prepare quasi-carbon fibers from stabilized PAN fibers using various quasi-carbonization cycles and to examine their properties. Two temperature regions, up to 800$^{\circ}C$ and above 1000$^{\circ}C$, were used for quasi-carbonization processes. The chemical composition, physical properties, thermal stability, microstructure, mechanical properties and electrical resistivity of the quasi-carbon fibers prepared with different final heat-treatment temperatures, heating rates, holding times, heating steps, and purging gas purity were extensively examined. The results were also compared with those from stabilized PAN fiber and commercial PAN-based carbon fiber. The present study showed that a variety of properties of quasi-carbon fibers significantly depended on several quasi-carbonization process parameters.

• Korean Chemical Engineering Research
• /
• v.60 no.1
• /
• pp.159-168
• /
• 2022

Catalytic activity in ammonia decomposition reaction was studied on Mo-Al nitride obtained through temperature programmed nitridation of calcined Mo-Al mixed oxide prepared by varying the MoO₃ quantity in the range of 10-50 wt%. N₂ sorption analysis, X-ray diffraction analysis (XRD), X-ray photoelectron spectroscopy (XPS) and H₂-temperature programmed reduction (H₂-TPR), and transmission electron microscopy (TEM) to investigate the physicochemical properties of the prepared catalyst were performed. After calcination at 600 ℃, the XRD of Mo-Al oxide showed γ-Al₂O₃ and Al₂(MoO₄)₃ phases, and the nitride after nitridation showed an amorphous form. The specific surface area after nitridation by topotactic transformation of MoO₃ to nitride was increased due to the formation of Mo nitride, and the Mo nitride was observed to be supported on γ-Al₂O₃. As for the catalytic activity in the ammonia decomposition reaction, 40 wt% MoO₃ showed the best activity, and as the nitridation time increases, the activity increased, and thus the activation energy decreased.

• Journal of the Korea Concrete Institute
• /
• v.29 no.2
• /
• pp.141-148
• /
• 2017

This study is experimentally investigated the effects of various steam curing parameters on the early-age compressive strength development of high strength concrete (over 40 MPa) in the precast plant production. High strength concrete are used only ordinary portland cement (type I) and water-cement ratio selected 3cases (25%, 35% and 45%). Also, steam curing parameters are as followings ; (1) Preset period 2cases (3 hours and 6 hours) (2) Maximum curing temperature 3cases ($45^{\circ}C$, $55^{\circ}C$ and $65^{\circ}C$) (3) Maintenance time of curing temperature 3cases (4 hours, 6 hours and 8 hours) (4) Maximum rate of heating and cooling $15^{\circ}C$/hr. Initial setting time and adiabatic temperature rising ratio of these concrete according to water-cement ratio are tested before main tests and examined the compressive strength development for the steam curing parameters. Also compressive strength are compared with optimum steam curing condition and standard curing at test ages. As test results, the optimum steam curing conditions for high strength concrete(over 40 MPa) are as followings. (1) Preset period ; over initial setting time of concrete (2) Maximum curing temperature ; bellow $55^{\circ}C$ (3) Maintenance time of curing temperature ; bellow 6hours. Also strength development of steam curing concrete show in the reversed strength at 28 days. It is to propose an efficient steam curing condition for high strength concrete in the precast method.

• Applied Chemistry for Engineering
• /
• v.7 no.5
• /
• pp.902-912
• /
• 1996

In the skeletal isomerization of 1-pentene over various solid acid catalysts, we have studied catalytic reactivity, selectivity, reaction mechanism and the relation between acid strength of catalysts and catalytic activity. Natural zeolite shows highest activity among the all catalysts and the modified ${\eta}$-alumina with fluorine and sulfuric acid shows higher activity than unmodified ${\eta}$-alumina. The yield of isopentene increases with increasing temperature and increasing contact time. However the cracking products increase at the high temperature and very high contact time. In addition, the activity of natural zeolite exchanged with metal cation decreases and shows good relation with the polarizing power of metal cation. According to the result of ammonia TPD, the acid strength of catalysts has an effect on catalytic activity.

• Journal of the Microelectronics and Packaging Society
• /
• v.10 no.2
• /
• pp.19-26
• /
• 2003

Plastic and creep deformations of a solder joint on thermal cycle play an important role in the reliability of optical telecommunication components. Solder joint strain is increased with the thermal cycle time and it causes mis-alignments and power loss in the optical component. Furthermore, the component can be failed since the deformation exceed the limitation of the fatigue life. We applied the finite element analysis method to solve the problem of the solder joint reliability on thermal cycle. Plastic and creep deformations are calculated by the finite element method. And, the fatigue lire is predicted by using creep-fatigue prediction models with calculated strains. The temperature conditon of the analysis was referred from the Telcordia reliability schedule (-40 to 75). Also, the three ramp renditions, 1/min, 10/min and 50/min, and dwelling time were considered to analyze the differences of results.

• Polymer(Korea)
• /
• v.38 no.2
• /
• pp.171-179
• /
• 2014

Low temperature cure prepregs are being developed for use in the preparation of large-structured fiber-reinforced polymer (FRP) composites with good performance. Cure behavior and chemorheology of low temperature cure epoxy resin system, based on epoxy resin, curing agent, and accelerators, were investigated to provide a matrix resin suitable for the prepreg preparation. Characteristics of cure reaction were studied in both dynamic and isothermal conditions by means of differential scanning calorimetry and rheometry. The low temperature cure epoxy resin system suggested in this study as a matrix resin was curable at $80^{\circ}C$ for 3 h, and showed the gel times of 120 and 20 min at 80 and $90^{\circ}C$, respectively. Thermal and mechanical properties of the cured sample were almost the same as high temperature cure counterparts.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.10a
• /
• pp.211-214
• /
• 2004

In the present study, the effect of SIDT (Strain Induced Dynamic Transformation) on the microstructure of medium carbon steels was investigated to develop spheroidized annealing-free steel wire rods. When $0.45\%C$ steels were hot-deformed under the conditions of heavy reduction at low temperatures, a microstructure quite different from conventional ferrite-pearlite structure was obtained. It was considered that this ferrite-cementite microstructure was obtained because very small retained austenite grains existing between fine SIDT ferrites prefer to transform to cementite and ferrite instead of pearlite during cooling. Through the present study, $0.45\%C$ steels containing ferrite-cementite (FC) structure instead of ferrite-pearlite structure was obtained in as-rolled state by introducing SIDT. The specimen containing the FC structure was much softer than that containing conventional ferrite-pearlite structure. Therefore, it is concluded that deforming medium carbon steels under the conditions of SIDT is a very powerful method to obtain soft steel wire rods which could be cold-forged without softening heat-treatment

• Journal of the Korean Ceramic Society
• /
• v.35 no.6
• /
• pp.640-646
• /
• 1998

Nucleation and crystallzation of a quaternary glass system for lead titanate glass-ceramics were in-vestigated using DTA(differential thermal analysis ) with variation of nucleation temperature and crystal growth time. Glass samples containing 60mol% of PbO-{{{{ { TiO}_{2 } }} were prepared from melts by the conventional normal cooling method in a cylindrical brass mould. The glass sample was nucleated between 40$0^{\circ}C$ and 50$0^{\circ}C$ for a given time and showed the maximum nucleation rate at 46$0^{\circ}C$ The DTA crystallization peak temperature decreased with increasing nucleating time and decreasing heating rate during DTA runs which indicated an increase of the number of nuclei produced in the system.

• Journal of the Korean Ceramic Society
• /
• v.36 no.1
• /
• pp.89-96
• /
• 1999

Manufacturing conditions of the porous alumina mold were established to overcome various limits of the gypsum mold. For the preparations of the porous alumina mold, an activated charcoal was added to the Al2O3 with the wt% variation and then mixed. The binary slurry was study dispersed based on the examination of the ESA and rheological behaviro. The cylinder type alumina mold was cast in the gyspum mold and characterized by the shrinkage rate at the variable sintering temperature and the resistance against wear. It was proper to make a sintering of the Al2O3 by the surface diffusion which was non-shrinkage sintering mechansim, and intergranular neck growed stronger while sintering was being made. We studied a sintering by three categories; 1) thermodynamic method below 1,000$^{\circ}C$, 2) kinetic method above 1,000$^{\circ}C$ and 3) combined method. In the results of the respective works, combined method was superiro to the others. The prepared Al2O3 mold had relatively high strength, low drying rate, the resistance against the acid or base and good casting behavior.