• International Journal of Highway Engineering
• /
• v.9 no.4
• /
• pp.149-158
• /
• 2007

Evaluation of the asphalt mixture modified with crumb rubber modifier(CRM) was performed to estimate possibility of using it as a paying material. OACs(optimum asphalt content) of CRM modified asphalt mixtures by dry process and wet process were determined by Marshall mix design and Wheel tracking test and moisture susceptibility test by freezing and thawing were carried out with CRM modified asphalt mixtures at OACs. The results from these tests, resistance of permanent deformation of CRM modified asphalt mixtures were superior to one of AP-5 while showing very low resistance of moisture sensitivity by freezing and thawing. This means that CRM modified asphalt mixtures are very sensitive to freezing and thawing. However, CRM modified asphalt mixture with anti-stripping material showed high improvement to resistance of moisture susceptibility by freezing and thawing. Therefore, it is recommended that when CRM mixtures were used in domestic, CRM modified asphalt mixtures should be with prevention against freezing and thawing resistance by moisture susceptibility.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.35 no.7
• /
• pp.886-890
• /
• 2006

Rice flours produced by dry, wet, and semi-wet milling methods were used to investigate bread-making properties. Wet milled rice flours were produced by two different steeping temperatures of $25^{\circ}C$ and $55^{\circ}C$, properties of composite flour containing 70% rice flour and 30% wheat flour with the addition of vital wheat gluten were tested. Among rice flours, wet milled rice flour showed increased mixing time and dough stability determined by a mixograph. Wet milled rice flours produced higher loaf volume compared with dry of semi-wet milled rice flours. Wet-milled rice flour steeped at $55^{\circ}C$ appeared to produce good rice breads with relatively high loaf volume. Crumb hardness of bread prepared with wet milled rice flour was lower than the other breads and increased slowly during 3-day storage at $25^{\circ}C$.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.32 no.6D
• /
• pp.615-622
• /
• 2012

The aim of shotcrete is to increase the bearing capacity and to protect the excavated surface from erosion by preventing falling of rock mass. Shotcreting method is divided into two types as dry process and wet process. Since 1997, wet process method has been used more frequently than dry process method in field works. The failure to bond, so called rebound, occurs in many case during shotcrete works. The excess amount of rebound has a significant effect on the total construction cost. For example, material and craft-man cost increases, the shooting time delays due to deceleration of work execution stage, work efficiency of craft-man decreases and additional cost to remove the muck generates. In this study, therefore, the experimental analysis of rebound amount and strength was conducted by analyzing the actual construction data for wet process type of shotcreting method upon accelerator contents. Also, the effective and rational method was suggested, which can be actually implemented in the Korea construction sites.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.8
• /
• pp.887-892
• /
• 2014

In a conventional magnetic abrasive polishing process, the polishing abrasives are mixed with ferrous particles and slight cutting oil to form a cluster of abrasives. However, when a tool rotates at a high revolution speed, most of the polishing abrasives are scattered away from it due to the increase in centrifugal force. This phenomenon directly reduces the polishing efficiency. The use of a highly viscous matter such as silicone gel instead of cutting oil for mixing is one method to solve this problem and increase abrasive adhesion. Another method to avoid high abrasive scattering is the application of wet magnetic abrasive polishing (WMAP). In WMAP, abundant mineral oil is preliminarily applied to the workpiece surface. This study experimentally evaluated the effect of WMAP on abrasive adhesion. The relationship between the amount of working abrasives and polishing conditions was characterized. Despite the lower adhesion ratio of polishing abrasives, the surface roughness was found to be significantly improved as the result of WMAP.

• The Korean Journal of Food And Nutrition
• /
• v.28 no.6
• /
• pp.1065-1070
• /
• 2015

A high-yield Korean rice cultivar cv. Boramchan and Hanmaeum, and rice cultivar for use in staple cv. Hopum were prepared and investigated for their physiological characteristics. Water content, water holding capacity, amylose content, damaged starch content, particle size, and pasting properties of the rice flours were measured. Moisture content of the Boramchan and Hanmaeum, made under wet and dry milling conditions, were as follows: wet conditions (14.79% and 13.56% respectively) and dry conditions (7.98% and 7.14% respectively). Water holding capacity of the Boramchan and Hanmaeum made by wet milling condition was 236.67% and 231.35%, respectively. Water holding capacity of the samples made by dry milling condition showed a higher score compared with other samples. The amylose content of Hopum, Boramchan, and Hanmaeum made by dry milling condition were 19.12%, 19.55% and 19.59%, respectively. Damaged starch contents of the samples made by wet milling showed a lower score. Final viscosity of Hopum, Boramchan, and Hanmaeum made by wet milling condition was 2,604, 3,052, and 2,917 cp, respectively. In this study, the results indicated that the super-yield Korean rice flour made by wet milling condition tends to show a lower water holding capacity, damaged starch contents and particle size, as compared to controls. However, a setback of the super-yield Korean rice flour was a higher score as compared to the controls, regardless of the milling conditions.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2004.06a
• /
• pp.243-244
• /
• 2004

금속성 방사성폐기물을 제염하는 설비의 조건으로는 제염계수, 2차 폐기물 발생량, 모재의 회수가능성, 작업자의 안전성(원격조정) 등을 고려하여야 한다. 금속성 방사성폐기물의 오염제거 방법으로 습식제염 방법을 손쉽게 생각할 수 있으나 습식제염은 모재로부터 오염 물질을 선택적으로 제염이 불가능하고 강산 용액을 사용하므로 제염후 발생되는 2차 액체폐기물로 인해 최근 그 적용이 제한되고 있다.(중략)

• Proceedings of the Korean Environmental Sciences Society Conference
• /
• 2008.11a
• /
• pp.571-574
• /
• 2008

계량 습식방법으로 실험한 결과 다른 처리 방법과는 달리, 물리성과 환경성 모든 항목에서 적합함을 나타내었다. 그러므로 원예농업용 폐비닐의 저급물리성과 중금속등의 유해 물질 검출의 우려로 인한 사용기피를 조금이나마 불식하고 기존에 유해성분 검출로 토양이나 작물에 문제가 됐던 원예농업용 자재를 대체할 수 있는 자재로서의 가능성을 보였다고 할 수 있다.

• Korean Journal of Human Ecology
• /
• v.3 no.2
• /
• pp.68-76
• /
• 2000

The quality of Injulmi, waxy rice cake is affected by milling methods. varieties. additives, steeping condition before milling and the texture properties during storage. Sinsunchalbyeo and Hwasunchalbyeo flours were made using pin-dry milling(PDM) and roller-wet milling( RWM) methods. Injulmi was made from those flours with different sugars, sucrose, maltose. oligosaccharide, and were measured textural properties of Injulmi stored at 2 $0^{\circ}C$ for 0, 12, 36 and 60 hrs, respectively. The hardness of sucrose added to injulmi made from PDM flour was the highest among any other sugars, but Injulmi from RWM flour was increased in the following order sucrose>maltose>oligosaccharide>non - added Injulmi. Adhesiveness of none added Injulmi were the lowest among sugar added Injulmi including, oligosaccharide, maltose and sucrose added Injulmi.

• Journal of the Korea Concrete Institute
• /
• v.20 no.5
• /
• pp.543-548
• /
• 2008

Solid hydrated by hydro-thermal synthesis reaction is cured two times, the first curing is the steam curing at atmospheric pressure and the second one is a high-pressure steam curing, that is autoclaving. Steam curing is to acquire the proper strength for the resistance of treatment in the first curing process, it was not evaluated properly so far. Because of ignorance about curing, some engineers even think that the dry curing is better than the steam curing. The relation between compressive strength of solid hydrated by hydrothermal synthesis reaction and curing condition are presented in this paper. In order to investigate the effect of curing on the strength properties of specimen, the hydration behavior of solid hydrated by hydro-thermal synthesis reaction has been studied over curing condition using XRD, DT-TGA and porosimeter, SEM analysis technique. The results show that the specimens which are cured with blended method of dry and steam curing appear to have better strength properties than that of dry curing and steam curing. Also, there are significant difference of hydration behavior among curing condition in the solid hydrated by hydro-thermal synthesis reaction.

• Journal of Korea Foundry Society
• /
• v.43 no.5
• /
• pp.260-263
• /
• 2023

이 보고서에서는 무기 공정에서의 무기 인공 재생 모래의 특성을 중심으로 다음과 같이 정리할 수 있다. 1) ICP 발광 분광 분석을 통한 재생 모래의 Na⁺ 용출량, TP 휨강도 및 충전 밀동에는 높은 상관 관계가 확인되었다. 2) 현행 재생 방법 대비, 습식 연마 처리를 첨가함으로써 잔류 점결재가 제거되고 Na+ 용출량이 저감된 결과, 재생 모래의 TP 휨강도를 보다 개선 가능한 것이 확인되었다. 3) 재생 처리 공정 순서를 건식 연마 → 습식 연마 → 배소 처리로 함으로써, 가장 Na⁺ 용출량이 낮고, 높은 휨강도를 얻을 수 있는 것이 확인되었다. 4) 습식 연마 단계를 거치지 않고 배소 처리 온도와 처리 시간을 궁리함으로써 충분한 품질의 재생 모래를 얻을 수 있는 가능성이 시사되었다. 마지막으로, 무기 공정은 유기 공정에 비해 압도적으로 냄새가 적고 생산성이 높으며 인공 모래와의 병용을 통한 재생 처리시의 폐기물량 저감, 주조품의 고품질화 등 이점이 기대되는 공정이다.