• 설비공학논문집
• /
• 제14권5호
• /
• pp.385-390
• /
• 2002

To clarify the hydraulic characteristics of ice slurry which made from 6.5% ethylene glycol-water solution flowing through circular pipes of small diameter, experimental studies were performed. The flow pattern was observed and the pressure drop was measured in acrylic pipes with inner diameter of 24 mm. The results of flow visualization revealed that ice particles flowed along the top of pipes in the ranges of small ice fraction and low flow rate, while Ice particles diffused into the whole region of pipes flowed like a homogeneous flow for high flow rate and high ice fraction. An increase in frictional pressure drop was measured as the ice fraction increased in all pipes and unstable flow was observed for up-ward vertical pipe.

• 설비공학논문집
• /
• 제16권2호
• /
• pp.142-149
• /
• 2004

Recently, the government introduced the thermal storage system for reducing the electric power load. Especially, the ice slurry type has gained lots of interest due to its good heat transfer and flowing characteristics. This study was peformed to understand the effects of transporting ice slurry through elbows of various angle. Propylene glycol water solution was used and about 2 mm ice particles were circulated. The experiments were carried out under various conditions, such as concentration and velocity of water solution ranging between 0∼20 wt％, 1.5∼2.5 m/s, respectively. And elbows with 4 different angles of 30$^{\circ}$, 45$^{\circ}$, 90$^{\circ}$, 180$^{\circ}$. The differential pressure and IPF (ice packing factor) between the pipe entry and exit were measured. The tendency of pressure loss and outlet IPF in elbow is that the pressure loss was reduced as concentration and flow velocity of water solution is increased, and low value appeared at 10 wt％ and 2.5 m/s. The variation of outlet IPF was compared with the inlet IPF in the range of $\pm$20％.

• 설비공학논문집
• /
• 제16권11호
• /
• pp.1028-1034
• /
• 2004

Recently, the ice storage system using ice slurry has been used increasingly since it has been introduced where the rapid cooling load change is required. Because it overcomes a decrease of the melting performance and an increase of the thermal resistance on the ice layer in static ice thermal storage system. This study is performed to understand the effects of transporting ice slurry through horizontal, vertical and inclined tubes ($30^{\circ},\;45^{\circ}$). It used propylene glycol-water solution and ice particles (diameter of about 2 mm) in this experiment. The experiments were carried out under various conditions, with concentration of water solution ranging from 0 to $20wt\%$, and velocity of water solution at the entry ranging from 1.5 to 2.5 m/s. The results were as follows: Regarding the angle of inclined tube, the highest pressure loss was measured for vertical tube and the pressure loss for $45^{\circ},\;30^{\circ}$, horizontal straight tubes were lower successively. The lowest pressure loss in these tubes was measured at velocity of $2.0{\sim}2.5m/s$ and concentration of $10wt\%$. The outlet IPF was likewise stable in these ranges.

• 한국건설순환자원학회논문집
• /
• 제9권1호
• /
• pp.58-65
• /
• 2021

본 연구에서는 순환유동층 보일러 애쉬의 재활용 가능성을 높이기 위한 방법으로, 경량기포콘크리트의 제조시 생석회 및 황산칼슘 성분이 필요하다는 점에 착안하여, 이를 생석회 및 석고의 대체재로 활용하여, 생산원가 절감, 자원재활용, 환경부하 저감 및 고부가가치화 등의 목표를 달성하고자 하였다. 다양한 배합설계를 도출하여 경량기포 콘크리트 물성을 평가하였고, 이를 바탕으로 실제 공장에서 시제품을 생산하여, 경량 기포 콘크리트의 제조에 순환유동층 보일러애쉬의 활용성을 검증하고자 하였다. 실험 결과에 따르면, 순환유동층 보일러애쉬를 슬러리로 선처리하여 활용하는 방법을 통해 석고를 CFBCA로 대체 가능한 것이 확인되었으며, 이를 통해 경쟁력 있는 경량기포 콘크리트 제품의 생산이 가능함을 보였다.

• 설비공학논문집
• /
• 제17권7호
• /
• pp.635-641
• /
• 2005

This study experimented to understand the effects of transporting ice slurry through elbow and inclined tube. And at this experiment it used propylene glycol-water solution and a diameter of about 2mm ice particle. The experiments were carried out under various conditions, with velocity of water solution at the entry ranging from 1.0 to 3.5 w/s and elbows and inclined tubes of 4 kinds angle with $30^{\circ},\;45^{\circ},\;90^{\circ}\;and\;180^{\circ}$. The pressure drop between the tube entry and exit were measured. According to angle of bending, the highest pressure drop was measured at $30^{\circ}$ elbow and the lowest pressure drop was measured at $90^{\circ}$ elbow, and there are only a little differences of pressure drop between $45^{\circ}$ elbow and $180^{\circ}$ elbow. According to angle of inclined tube, the highest pressure drop was measured at $90^{\circ}$ inclined tube and the pressure drop at $45^{\circ},\;30^{\circ},\;180^{\circ}$ inclined tubes were lower successively. The lowest pressure drop in elbows and inclined tubes was measured at velocity of $2.0\~2.5$ m/s and concentration of $10\;wt\%$.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2009년도 추계학술발표대회
• /
• pp.18.1-18.1
• /
• 2009

금속 다공체는 자동차, 선박, 건축 등의 분야에서 구조물이나 충격흡수제 등으로 응용되고 있는데 이들은 일반 금속 구조물에 비해 가볍고 플라스틱에비해서는 강한 장점을 지닌다. 현재 사용되고 있는 대부분의 금속 다공체는 발포 주조공정으로 제조된 알루미늄으로서, 철계 합금에 비해 가벼운 장점을 갖지만 강도가 상당히 떨어지고 가격이 높은 단점을 가진다. 따라서 본 연구에서는 알루미늄 대신 철계 합금으로 다공체를 제조하고자 하였고 제조방법으로는 주조공정 대신 분말공정을선택하였다. 분말공정은 구형 스티로폼을 금속분말 슬러리로 코팅한 후 스티로폼을 제거하여 낱개의 금속중공체(Metallic Hollow Sphere)를 제조하고 이렇게 제조된 중공체를 뭉쳐 성형함으로써최종 형상의 다공체를 제조하는 방법이다. 이 방법으로 제조된 다공체는 주조공정으로 제조된 다공체보다높은 강도를 나타내며 낱개의 중공체는 성형공정을 거치지 않고 필터나 충진재 등의 새로운 용도로 활용될 수 있다.

• 설비공학논문집
• /
• 제14권5호
• /
• pp.391-397
• /
• 2002

Pressure drop were experimentally investigated for ice slurry flowing in the acrylic pipes with inner diameter of 24 mm. Ice slurry was made from 6.5% ethylene glycol-water solution, and the pipes is consisted of horizontal, vertical (upward and downward) and $90^{\circ}$ elbow pipe. The ice Packing factor (IPF) and the flow rate of the experiments were varied from 0 to 30% and from 5 to 70kg/min respectively The measured pressure drop in various pipe positions were compared with those for the solution flow (IPF=0). The pressure drop was larder than that for solution flows as the IPF increased when the flow rate was low or very high. Sharp increases in pressure drop were observed for the cases when IPF is more than 70% in horizontal and vertical pipes, whereas the pressure drop increased with the IPF simultaneously in an elbow pipe.

• 한국전기전자재료학회논문지
• /
• 제21권3호
• /
• pp.236-241
• /
• 2008

The effect of organic solvent mixture ratio on the rheology property of slurry and thickness control of ceramic green sheet was investigated. For selecting a suitable dispersant multiple light scattering method was used to evaluate the particle migration velocity and variation of clarification layer thickness. Using the selected dispersant the dispersion property of solution according to solvent mixture ratio was investigated. Binder and plasticizers were added to formulate slurries and their viscosity was evaluated according to solvent mixture ratio. Ceramic green sheets with average thickness of 30, 50 urn were fabricated via tape casting and their thickness tolerances measured. As a result according to solvent mixture ratio the solution and slurry properties varied and for the mixture ratio of ethanol/toluene of 80/20 the ceramic green sheet with the lowest thickness tolerance was obtained.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.922-927
• /
• 2003

In this paper, slurry fluid motion, abrasive particle motion, and roles of groove patterns on the pads are numerically investigated in the 2D and 3D geometries. The simulation results are analyzed in terms of experimental removal rate and WIWNU (within wafer non-uniformity) for ILD (inter level dielectric) CMP process. Numerical investigations reveal that the grooves in the pad behave as uniform distributor of abrasive particles and enhance the removal rate by increasing shear stress. Higher removal rate and desirable uniformity are numerically and experimentally observed at the pad with grooves. Numerical analysis is very well matched with experimental results and helpful for understanding polishing mechanism and local physics.

• 대한토목학회논문집
• /
• 제26권5C호
• /
• pp.303-312
• /
• 2006

본 연구에서는 급결성 유동화 뒷채움 재료의 역학적 특성을 파악하여 토질 조건에 따른 배합비 설계 기준을 제시하고 거동 특성을 파악하는데 그 목적이 있다. 국내 토질 여건을 고려하여 사질토(SW-SM)에 자갈과 점토의 혼합비를 차별적으로 적용하여 사질토는 SP와 SW-SM, 점토는 CH, 그리고 혼합토는 SW-SM, SP-SM, SC, 그리고 GP-GM등 총 17종류의 대상토를 선정하였으며 대상토에 고결재료와 물을 혼합하여 급결성 유동화 뒷채움재로 사용하였다. 본 연구결과 고화재의 종류와 양을 차별적으로 적용하여 만든 뒷채움재는 기존의 모래로 다짐된 뒷채움재의 특징인 유지 및 보수를 위한 재굴착성 뿐만 아니라 고유동성, 굴착잔토의 재활용성 등 많은 장점들을 가지고 있어 모래 뒷채움재를 대체 할 수 있다고 판단되어 토질 조건에 따라 배합비 설계기준을 제시하고 거동 특성을 파악하였다.