• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.05a
• /
• pp.191-194
• /
• 2009

Very big springback in advanced high strength steel(AHSS) sheets invokes undesired shape defects, which can be eliminated by the tool surface correction method or the forming process control method. Since the springback reduction by controlling the forming process is limited, in this study, the die correction method which finds die correction from the relationship between die design variable and springback is introduced to achieve springback reduction and is applied to the automotive side rail to reduce the springback of 75.8% within the assembly limit of 1 mm.

• Transactions of Materials Processing
• /
• v.9 no.5
• /
• pp.526-532
• /
• 2000

Springback simulation is receiving increasing attention throughout the automotive industry and the academic world. The knowledge of the real springback of stamped parts can help the stamping technicians to modify the process parameters or die geometry in order to reduce the shape defect. This paper presents the results of springback simulation after aluminium square cup deep drawing and trimming simulation, and results of springback optimization using response surface method.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.4
• /
• pp.483-490
• /
• 2013

In aluminum sheet metal forming, the conventional forming methods of T4 or T6 heat-treated sheets result in low formability and dimensional accuracy. This study suggests a new forming method for aluminum sheets called as hot forming quenching (HFQ) that solves the problems faced in the conventional method. HFQ combines the heat treatment and forming processes through the forming die during the quenching of a solid solution. To evaluate the application of HFQ to the sheet forming of aluminum, an Erichsen and V-bending test are performed in this study to measure the dimensional accuracy and formability, which are then compared with those of the conventional forming method. Furthermore, the strength and hardness of the products formed by HFQ are measured to confirm the degradation in mechanical properties compared with the conventional forming method, which shows the validity of the application of HFQ to aluminum sheet metal forming.

• Transactions of Materials Processing
• /
• v.14 no.4 s.76
• /
• pp.392-398
• /
• 2005

The deterioration of dimensional accuracy, caused by springback, is one of problems to always occur In sheet metal forming processes. As the demand for lighter and stronger metals increases, the development of improved forming processes settling the springback problem becomes more important. In this work, asymmetric springback phenomena are investigated, which occur in the shallow-drawing process with the anisotropic sheet metal and axisymmetric tools. The improvement possibility of dimensional accuracies, mainly, flatness, was examined by applying segmented blank holding forces as a method for springback control.

• Transactions of Materials Processing
• /
• v.12 no.3
• /
• pp.208-213
• /
• 2003

The methodology to design initial blanks considering the reduction of both springback and flange trimming amounts is studied. Three dimensional forming analysis of a trial blank Is first carried out using FEM and the tentative Initial blank shape is then determined by cutting the outer edge of the trial blank whose shape is nearly matched with the trimming line. During the shaping the blank edge, tile movement of blank outer line is described with random variables to reduce the sensitivity of initial blank geometry. After performing 2-D FEM forming and springback simulations for selected sections and optimizing the trimming and springback amounts in terms of section length of the blank, the initial blank is finally determined. In order to see tile springback reduction in the initial blank determined by the proposed method, a stepped s-rail is stamped and the sppingback is measured. The springback of newly designed initial blank of stopped s-tail is tremendously reduced.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2006.05a
• /
• pp.345-348
• /
• 2006

The focus of this study is placed on the reduction of springback in the separator plate which is one of main components of the MCFC stack. Firstly, the current design (round punch and die) is accessed using FEM to find out how much it springs back after the forming operation. In this study, the two kinds of modified designs are proposed in order to reduce the amount of springback. With the linear punch in the first modified design the amount of springback rather increased. In the second modified design of die with holes, the amount of springback decreased drastically due to the effect of compression at the die corner.

• Transactions of Materials Processing
• /
• v.26 no.5
• /
• pp.277-285
• /
• 2017

Vehicle weight reduction is a known strategy to improve fuel efficiency and strengthen exhaust gas regulation. The use of high strength steel can satisfy safety, efficiency, emission, manufacturability, durability, and cost requirements. However, springback of high strength steel results in undesired shape defects. Springback is one of the most important issues of high strength steel for many applications in an automobile. Servo press has various capabilities to improve defects, process conditions, and productivity problems when forming a high strength steel. Especially, servo press can be set to function with variable slide motion in a single operation. In this study, the effect of servo press slide motion on 980MPa high strength steel was investigated through U-bending test.

• Transactions of Materials Processing
• /
• v.21 no.7
• /
• pp.397-402
• /
• 2012

The flange hub is a main component in an automotive steering system. In general, the flange hub are fabricated by mechanical machining, which is a process where material waste is inevitable. It is well-known that a net-shape cold forging cannot only reduce material waste but can also improve the mechanical strength of the final product. Thus, a forging process design was conducted for production of a flange hub. Significant spring-back occurs around the flange due to its small thickness in conjunction with the residual stresses after forging. In order to achieve the required dimensional accuracy, a process design with appropriate spring-back control is needed. In this study, a modification of the forging die was designed based on FE analysis with the purpose of spring-back compensation. Four kinds of different die designs were evaluated and the optimum design has two times less spring-back than the initial design. The compensation angle of the optimum design is 0.5 degrees. The results have been experimentally confirmed by cold forging of a flange hub and comparing the amount of spring-back between the actual component and the FE analysis.

• Transactions of Materials Processing
• /
• v.15 no.4 s.85
• /
• pp.295-303
• /
• 2006

Optimization is carried out to determine process parameters which reduce the amount of springback and improve shape accuracy of a deep drawn product in sheet metal forming process. The study uses the amount of stress deviation along the thickness direction in the deep drawn product as an indicator of springback instead of springback simulation. The scheme incorporates with an explicit elasto-plastic finite element method for calculation of the final shape and the stress deviation The optimization method adopts the response surface method in order to seek for the optimum condition of process parameters such as the blank holding force and the draw-bead force. The present scheme is applied to design of the variable blank holding force in an U-draw bending process and the application is further extend ε d to the design of draw-bead force in a front side member formed with advanced high strength steel (AHSS) sheets of DP60. Results show that design of process parameter is well performed to decrease the stress deviation through the thickness and to reduce the amount of springback. The present analysis provides a guideline in a design stage for controlling the springback based on the finite element simulation of the complicated parts.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2006.06a
• /
• pp.61-67
• /
• 2006

Optimization is carried out to determine process parameters which reduce the amount of springback and improve shape accuracy of a deep drawn product in sheet metal forming process. The study uses the amount of stress deviation along the thickness direction in the deep drawn product as an indicator of springback instead of springback simulation. The scheme incorporates with an explicit elasto-plastic finite element method for calculation of the final shape and the stress deviation. The optimization method adopts the response surface method in order to seek for the optimum condition of the draw-bead force. The present scheme is applied to the design of draw-bead force in a front side member formed with advanced high strength steel (AHSS) sheets of DP60. Results show that design of process parameter is well performed to decrease the stress deviation through the thickness and to reduce the amount of springback. The present analysis provides a guideline in a design stage for controlling the springback based on the finite element simulation of the complicated parts.