• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.5
• /
• pp.503-511
• /
• 2011

Water spray cooling is a significant technology for cooling of materials from high-temperature up to $900^{\circ}C$. The effects of cooling water temperature on spray cooling are mainly provided for hot steel plate cooling applications in this study. The heat flux measurements are introduced by a novel experimental technique that has a function of heat flux gauge in which test block assemblies are used to measure the heat flux distribution on the surface. The spray is produced by a fullcone nozzle and experiments are performed at fixed water impact density of G and fixed nozzle-totarget spacing. The results show that effects of water temperature on forced boiling heat transfer characteristics are presented for five different water temperatures between 5 to $45^{\circ}C$. The local heat flux curves and heat transfer coefficients are also provided to a benchmark data for the actual spray cooling of hot steel plate cooling applications.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.2
• /
• pp.203-212
• /
• 2010

Water spray cooling has been widely used in a variety of industrial applications. The present study concentrated on quantitative measurements of the heat flux and heat transfer coefficient by water spray as it impinges on the rough surface of a hot steel plate at $900^{\circ}C$. A novel experimental technique was developed for a hightemperature heat flux gauge with a test block, cartridge heaters, and thermocouples that was used to measure the surface heat flux information on the hot steel plate for local heat flux measurements. The roles of the surface roughness on heat transfer are presented in this paper for well-characterized four rough surfaces with average rms roughness heights of $40-80{\mu}M$. The results show that the local heat transfer for rough surfaces is higher than that for a smooth surface. Heat transfer can be significantly increased by the presence of surface roughness elements, which can disrupt the thin thermal boundary layer. In addition, the heat transfer enhancement mechanism on a rough surface can be investigated by a different boiling regime.

• Journal of the Korean Data and Information Science Society
• /
• v.25 no.4
• /
• pp.705-714
• /
• 2014

This study aimed at identifying the effect of vapocoolant spray and EMLA (eutectic mixture of local anesthetics) cream upon DPT (diphtheria-pertussis-tetanus)vaccineassociated injection pain in infants. A nonequivalent control group pretest-posttest design was used. The subjects were 49 infants, 19 of them for control group, 15 of them for vapocoolant group, and 15 infants for EMLA group. Pulse and oxygen saturation as pain indicators were measured before and after DPT vaccination. FLACC was also measured after vaccination. The data were collected between October 2009 and June 2010 and analyzed using SPSS WIN 20.0. EMLA group had significant a little changes in pulse (F=43.37, p <.001) and oxygen saturation (F=9.86, p=.003) compared to the control and vapocoolant group. But there was no difference in FLACC pain score among three groups. This results showed that EMLA cream is an effective agent for reducing DPT vaccination-associated pain. Therefore, EMLA cream can be used to reduce pain at public health centers and clinical settings.

• Proceedings of the SAREK Conference
• /
• 2005.06a
• /
• pp.92-92
• /
• 2005

• Journal of the Korean Society of Visualization
• /
• v.21 no.3
• /
• pp.33-38
• /
• 2023

Spray cooling is a method of cooling high-temperature heating elements by spraying droplets. Recently, spray cooling has been proposed for use in next-generation nuclear reactors. When droplets are sprayed onto the outer wall of a heat exchanger tube, a film boiling occurs on the outer wall. Over time, the outer wall temperature decreases, and a liquid film forms on the outer wall, and the heat exchanger outer wall is subsequently cooled by the liquid film. In this case, the liquid film thickness has a great influence on the heat removal performance. In this study, an experimental study was conducted to measure the liquid film thickness distribution in a droplet spray environment. For this purpose, a method using the electrical conductivity of the liquid was adopted.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.16 no.3
• /
• pp.116-120
• /
• 2006

We have investigated plasma spray coated $Al_2O_3$ layers on Al-60 series substrates for development of wafer electrostatic chuck in semiconductor dry etching system. Samples were prepared without/with cooling bar on backside of samples, at various distances, and with different powder feed rates. There were many cracks and pores in the $Al_2O_3$ layers coated on Al-60 series substrates without cooling bar on the backside of samples. But the cracks and pores were almost disappeared in the $Al_2O_3$ layers on Al-60 series substrates coated with cooling bar on the back side of samples, 15 g/min. powder feed rate and various 60, 70, 80 mm working distances. Then the surface morphology was not changed with various working distances of 60, 70, 80 mm. When the powder feed rate was changed from 15 g/min to 20 g/min, the crack did not appear, but few pores appeared. Also the $Al_2O_3$ layer was coated with many small splats compared with $Al_2O_3$ layer coated with 15 g/min powder feed rate. The deposited rate of $Al_2O_3$ layer was higher when the process was done without cooling bar on the back side of sample than that with cooling bar on the back side of sample.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.26 no.6
• /
• pp.779-787
• /
• 2002

The cooling heat transfer by impinging water spray jets on a rotating roll with a relatively large diameter has been investigated under various experimental conditions with 3 different sizes of flat type nozzle. The local heat transfer coefficients were calculated by finite difference method using measured surface temperatures of the circular cylinder as boundary conditions. Results show that a peak value of the heat transfer coefficient is located at the center of sprayed area and there may be a secondary peak at the downstream. The average heat transfer coefficients on the sprayed area were found to be 10 to 22 ㎾/$m^2$$^{\circ}C$, and were not related to spraying pressure, but approximately linearly to flow rate of sprayed water. Also it is found that increasing the distance from roll to nozzle could improve the cooling efficiency by increasing the sprayed area.

• Clinical and Experimental Pediatrics
• /
• v.51 no.5
• /
• pp.481-486
• /
• 2008

Purpose : The aims of this study were to test the efficacy of vapocoolant spray to decrease the symptoms associated with pain in newborns undergoing heel stick and intramuscular injection and compare the pain relief effect of oral glucose. Methods : Randomized, controlled study including sixty newborns undergoing heel stick and intramuscular injection. Group 1 was heelsticked, Group 2 was intramuscular injected, Group A did not recieve any treatment, Group B recieved 30% glucose solution orally, Group C was applied vapocoolant spray symptoms and signs associated with pain at heel stick and intramuscular injection were measured with the premature Infant Pain Profile (PIPP) scale. Results : There was no significant difference in the PIPP score between intramuscular injected group control and heel stick group control (P=0.07). The mean PIPP score of Group 1A (control) $10.6{\pm}2.4$, Group 1B $5.5{\pm}2.0$, Group 1C $5.2{\pm}1.8$. The mean PIPP score 1B and 1C were significantly lower than control (1B P<0.001, 1C P<0.001). The mean PIPP score of Group 2A (control) $12.5{\pm}1.4$, Group 2B $7.0{\pm}1.7$, Group 2C $6.4{\pm}1.6$. The mean PIPP score 2B and 2C were significantly lower than control (2B P<0.001, 2C P<0.001). Conclusion : The antinociceptive effect of vapocoolant sparay is as effective as 30% oral glucose solution for pain control. So this study support the use of vapocoolant spray for reducing pain during painful procedure in the neonatal intensive care units.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.202-202
• /
• 2012

유연성 투명 전도막은 현대 전자산업의 발전에 있어 필수적인 부품소재로서, 가시광선의 투과율이 80% 이상이고 면저항이 $100{\Omega}/sq.$ 전후이며 휘거나 접히고 나아가 두루마리의 형태로도 응용이 가능한 소재를 일컫는다. 이러한 유연성 투명 전도막은 차세대 정보디스플레이 산업 및 유비쿼터스 사회의 중심이 되는 유연성 디스플레이, 터치패널, 발광다이오드, 태양전지 등 매우 다양한 분야에 응용이 기대된다. 이러한 이유로 고 신뢰성 유연성 투명 전도막 개발기술은 차세대 산업에 있어서의 핵심기술로 인식되고 있다. 현재로서는 인듐 주석 산화물(indium tin oxide; ITO) 및 전도성 유기고분자를 사용하여 투명 전도막을 제조하고 있으나, ITO 박막의 경우 인듐 자원의 고갈로 인한 가격상승 및 기판과의 낮은 접착력, 열팽창계수의 차이로 인한 공정상의 문제, 산화물 특유의 취성으로 인한 유연소자로서의 내구성 저하 등의 문제가 제기되고 있다. 전도성 유기고분자의 경우는 낮은 전기전도도와 기계적강도, 유기용매 처리 등의 문제점이 지적되고 있다. 따라서 높은 전기전도도와 투광도 뿐만 아니라 유연성을 지니는 재료의 개발이 요구되고 있는 실정이다. 최근 이러한 재료로서 그래핀(graphene)과 탄소나노튜브(carbon nanotube; CNT)를 중심으로 하는 탄소나노재료가 주목받고 있으며 많은 연구가 활발히 진행되고 있다. 본 연구에서는 열화학기상증착법(thermal vapor deposition; TCVD)으로 합성된 그래핀 및 CNT를 이용하여 탄소나노재료 복합체 기반의 유연성 투명 전도막을 제작하고 그 특성을 평가하였다. 그래핀과 CNT합성을 위한 기판으로는 각각 300 nm 두께의 니켈과 1 nm 철이 증착된 실리콘 웨이퍼를 이용하였으며, 원료가스로는 메탄(CH4)과 아세틸렌(C2H2)등의 탄화수소가스를 이용하였다. 그래핀의 경우 원료가스의 유량, 합성온도, 냉각속도를 변경하여 대면적으로 두께균일도가 높은 그래핀을 합성하였으며, CNT의 경우 합성시간을 변수로 길이 제어합성을 도모하였다. 합성된 그래핀은 식각공정을, CNT는 스프레이 증착공정을 통해 고분자 기판(polyethylene terephthalate; PET) 위에 순차적으로 전사 및 증착하여 탄소나노재료 복합체 기반의 유연성 투명 전도막을 제작하였다. 제작된 탄소나노재료 복합체 기반의 유연성 투명 전도막은 물리적 과부하를 받았을 때 발생할 수 있는 유연성 투명 전도막의 구조적결함에 기인하는 전도성 저하를 보상하는 특징이 있어, 그래핀과 탄소나노튜브 각각으로 제조된 유연성 투명 전도막보다 물리적인 하중이 반복적으로 인가되었을 때 내구성이 향상되는 효과가 있다. 40% 스트레인을 반복적으로 인가하였을 때 그래핀 투명 전도막은 20 사이클 이후에 면저항이 $1-2{\Omega}/sq.$에서 $15{\Omega}/sq.$ 이상으로 급증한 반면 그래핀-CNT 복합체 투명 전도막은 30사이클까지 $1-2{\Omega}/sq.$ 정도의 면저항을 유지하였다.