• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.20 no.7
• /
• pp.6-13
• /
• 2006

Tin doped indium oxide(ITO) and Al doped zinc oxide(ZnO:Al) films, which are widely used as a transparent conductor in optoelectronic devices, were prepared by using the capacitively coupled DC magnetron sputtering method. ITO and ZnO:Al films with the optimum growth conditions showed each resistivity of $1.67{\times}10^{-3}[{\Omega}-cm],\;2.2{\times}10^{-3}[{\Omega}-cm]$ and transmittance of 89.61[%], 90.88[%] in the wavelength range of the visible spectrum. The two types of 5 inch-PDP cells with ZnO:Al and ITO transparent electrodes were made under the same manufacturing conditions. The PDP cell with ZnO:Al film was optimally operated in the mixing gas rate of Ne(base)-Xe(8[%]), and at gas pressure of 400[Torr]. It also shows the average measured brightness of $836[cd/m^2]$ at voltage range of $200{\sim}300$[V]. Luminous efficiency, one of the key parameter for high brightness and low power consumption, ranges from 1.2 to 1.6[lm/W] with increasing frequency of ac power supplier from 10 to 50[Khz]. The brightness and luminous efficiency are lower than those with ITO electrode by about 10[%]. However, these values are considered to be enough for the normal operation of PDP TV.

• Journal of the Korean Magnetics Society
• /
• v.20 no.6
• /
• pp.222-227
• /
• 2010

$BiFeO_3$ (BFO) thin films were deposited on Pt/Ti/$SiO_2$/Si(100) substrates by RF magnetron sputtering method at room temperature. The influence of the flow rate of $O_2$ gas on the preparation of $BiFeO_3$ thin films was studied. XRD results indicate that the $BiFeO_3$ thin films were crystallized to the perovskite structure with the presence of small amount of impurity phases. The flow rate of $O_2$ gas has great affect on the microstructures and magnetic properties of $BiFeO_3$ thin films. As flow rate of $O_2$ gas increased, roughness and grain size of the thin films increased. $BiFeO_3$ thin films exhibited weak ferromagnetic behavior at room temperature. The PFM images revealed correlation between the surface morphology and the piezoresponse, indicating that the piezoelectric coefficient is related to microstructure.

• Journal of the Korean Electrochemical Society
• /
• v.13 no.2
• /
• pp.89-95
• /
• 2010

The chalcopyrite $Cu(In_xGa_{(1-x)})Se_2$ (CIGS) is considered to be one of the effective light-absorbing materials for thin film photovoltaic solar cells. We describe the electrodeposition of CIGS thin films in ambient laboratory conditions, and suggest the electrochemical conditions to prepare stoichiometric CIGS thin films of Ga/(In + Ga) = 0.3. In acidic solutions containing $Cu^{2+}$, $In^{3+}$, $Ga^{3+}$ and $Se^{4+}$ ions, the CIGS films of different Cu/In/Ga/Se chemical compositions were electrodeposited onto Mo/Glass substrate. The structure, morphology and chemical composition of electrodeposited CIGS films were characterized by X-ray diffraction (XRD), Scanning electron microscopy (SEM), and Energy dispersive X-ray spectroscopy (EDS), respectively.

• Journal of the Korean Ceramic Society
• /
• v.38 no.11
• /
• pp.973-979
• /
• 2001

Tin-doped indium oxide (ITO) thin films were deposited using r.f. magnetron reactive sputtering and the electrical properties, such as the resistivity, carrier concentration and mobility, were investigated as a function of the sample position under a given magnetron sputtering condition. The nonhomogeneity of the electrical properties with the sample position was observed under a given magnetron sputtering condition. The resistivity of ITO thin film on the substrate which corresponded to the center of the target had a minimum value, 2∼4$\times$10$\^$-4/$\Omega$$.$cm, and it increased symmetrically when the substrate deviated from the center. The density measurement result also showed that ITO thin film deposited at the center has a maximum density of 7.0g/cm$^3$, which was a relative density of about 97%, and the density decreased symmetrically as the substrate deviated from the center. The nonhomogeneity of electrical properties with the deposition position could be explained with the incidence angle of the source beam alpha, which is related with an atomic self-shadowing effect. It was confirmed experimentally that the density in film affect both the carrier mobility and the conductivity. In the case where the density of ITO thin film is 7.0g/cm$^3$, the magnitude of the mean free path was identical with that of the grain size(the diameter of column). However, in the other cases, the mean free path was smaller than the grain size. These results showed that the scattering of the free electrons at the grain boundary is the major factor for the electrical conduction in ITO thin films having a high density, and there exists other scattering sources such as vacancies, holes, or pores in ITO thin films having a low density.ing a low density.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.62-62
• /
• 2008

As micro-system move toward higher speed and miniaturization, requirements for embedding the passive components into printed circuit boards (PCBs) grow consistently. They should be fabricated in smaller size with maintaining and even improving the overall performance. Miniaturization potential steps from the replacement of surface-mount components and the subsequent reduction of the required wiring-board real estate. Among the embedded passive components, capacitors are most widely studied because they are the major components in terms of size and number. Embedding of passive components such as capacitors into polymer-based PCB is becoming an important strategy for electronics miniaturization, device reliability, and manufacturing cost reduction Now days, the dielectric films deposited directly on the polymer substrate are also studied widely. The processing temperature below $200^{\circ}C$ is required for polymer substrates. For a low temperature deposition, bismuth-based pyrochlore materials are known as promising candidate for capacitor $B_2Mg_{2/3}Nb_{4/3}O_7$ ($B_2MN$) multi layers were deposited on Pt/$TiO_2/SiO_2$/Si substrates by radio frequency magnetron sputtering system at room temperature. The physical and structural properties of them are investigated by SEM, AFM, TEM, XPS. The dielectric properties of MIM structured capacitors were evaluated by impedance analyzer (Agilent HP4194A). The leakage current characteristics of MIM structured capacitor were measured by semiconductor parameter analysis (Agilent HP4145B). 200 nm-thick $B_2MN$ muti layer were deposited at room temperature had capacitance density about $1{\mu}F/cm^2$ at 100kHz, dissipation factor of < 1% and dielectric constant of > 100 at 100kHz.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.20 no.5
• /
• pp.216-220
• /
• 2010

Ni-Fe alloys have various applications such as thin film inductor, thin film transformer, magnetic head's shield case, etc. Magnetic properties of Ni-Fe thin films depend on the process parameters such as thickness, contents, deposition rate, substrates, etc. In this study, NiFe films with a thickness of about 150nm were deposited on Si(100) wafer and $SiO_2$/Si(100) substrate at room temperature by a DC magnetron co-sputtering using Fe and Ni targets. Their phase formation and magnetic properties as a function of annealing temperature were investigated with XRD, FE-SEM and VSM. The assputtered films have BCC structure. With increasing annealing temperature, NiFe thin film for $SiO_2$/Si(100) substrate transformed completely from BCC to FCC phase above $500^{\circ}C$, but some BCC phase remained above $500^{\circ}C$ on Si(100) wafer. For samples annealed at $450^{\circ}C$, squareness ratio of NiFe thin film shows peak value and its saturation magnetization is around 0.0118 emu, which means that the optimum annealing temperature of NiFe thin film seems to be $450^{\circ}C$. The saturation magnetization of films decreased rapidly above the annealing temperature of $500^{\circ}C$ due to phase transformation from BCC to FCC phase.

• Journal of the Korean Vacuum Society
• /
• v.21 no.4
• /
• pp.205-211
• /
• 2012

We investigated the optical and hydrophobic properties of the deposited silver (Ag) zinc oxide (ZnO) nanorods (NRs) on flexible indium tin oxide (ITO) coated polyethylene terephthalate (PET) substrates (i.e., ITO/PET). The ZnO NRs were grown by an electrochemical deposition using a sputtered ZnO seed layer and the Ag was deposited by using a thermal evaporator. For comparison, the same fabrication process was carried out on the bare ITO/PET without ZnO NRAs. Due to the discrete surface of ZnO NRs, the deposited Ag was formed as nano-scale particles, while the Ag became film-like for bare ITO/PET. In order to control the size and amount of Ag particles, the Ag deposition time was changed from 100 to 600 s. When the deposition time was increased, the Ag particles became larger and denser, and the absorptance was increased. This enhanced absorptance may be due to the localized surface plasmon resonance of Ag particles. Furthermore, the relatively high hydrophobicity was observed for the deposited Ag on the ZnO NRs/ITO/PET. These improved optical and surface properties are expected to be useful for flexible photovoltaic and optoelectronic devices.

• Journal of the Korean Vacuum Society
• /
• v.17 no.6
• /
• pp.560-565
• /
• 2008

$(Pb_{0.98}La_{0.08})(Zr_{0.65}Ti_{0.35})O_3$ (PLZT) thin films with $TiO_2$ buffer layers were deposited on Pt/Ti/$SiO_2$/Si substrates by an R.F. magnetron sputtering method in order to improve the ferroelectric characteristics of the films. And the ferroelectric properties and crystallinities of the PLZT thin films were investigated in terms of the effects of the post annealing temperatures of $TiO_2$ buffer layers between a platinum bottom electrode and PLZT thin film. The ferroelectric properties of the PLZT thin films improved as increasing of the post annealing temperatures of $TiO_2$ layers, thereby reaching their maximum at $600^{\circ}C$.

• Journal of Korean Society of Environmental Engineers
• /
• v.38 no.6
• /
• pp.291-298
• /
• 2016

Electrochemical water treatment process as a useful treatment method for the removal of non-degradable matter has been consistently studied for several decades. Key process of electrochemical water treatment are oxidation reaction from an anode and reduction from a cathode. In this study, the effect of pre-treatment methods in the insoluble electrode manufacturing process for the water treatment has been evaluated for the life time of electrode The results of this study showed that pre-treatment methods of a base metal such as surface roughness, clean method and interlayer formation influenced to life time of electrode when the same condition (catalyst electrode layer coating method and material system) was applied for pre-treatment methods. This study was conducted by using $IrO_2/Ti$ electrode In the test of sand-blasting process, an electrode manufactured by using sanding media of different sizes resulted in the most effective electrode life time when the size of alumina was used for $212{\sim}180{\mu}m$ praticle size (#80). The most effective method was considered using arc plasma in the additional roughness control and cleaning process, sputtering method to form Ta type interlayer formation process.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2000.02a
• /
• pp.123-123
• /
• 2000

선폭이 초미세화됨에 따라 게이트 전극에서의 공핍 현상 및 불순물 확산의 물제를 갖는 poly-Si 게이트를 대체할 전극 물질로 텅스텐(W)이 많이 연구되어 왔다. 반도체 소자의 배선물질로 일찍부터 사용되어온 텅스텐은 내화성 금속의 일종으로 용융점이 높고, 저항이 낮다. 그러나, 일반적으로 사용되고 있는 CVD에 의한 텅스텐의 증착은 반응가스(WF6)로부터 오는 불소(F)의 게이트 산화막내로의 확산으로 인해 MOS 소자가 크게 열화될수 있다. 본 연구에서는 W/TiN 이중 게이트 전극 구조를 갖는 MOS 캐패시터를 제작하여 전기적 특성을 살펴보았다. P-Type (100) Si위에 RTP를 이용, 85$0^{\circ}C$에서 110 의 열산화막을 성장 및 POA를 수행한 후, 반응성 스퍼터링법에 의해 상온, 6mTorr, N2/Ar=1/6 sccm, 100W 조건에서 TiN 박막을 150, 300, 500 의 3그룹으로 증착하였다. 그 위에 LPCVD 방법으로 35$0^{\circ}C$, 0.7Torr, WF6/SiH4/H2=5/5~10/500sccm 조건에서 2000~3000 의 텅스텐을 증착하였다. Photolithography 공정 및 습식 에칭을 통해 200$\mu\textrm{m}$$\times$200$\mu\textrm{m}$ 크기의 W/TiN 복층 게이트 MOSC를 제작하였다. W/TiN 복측 게이트 소자와 비교분석하기 위해 같은 조건의 산화막을 이용한 알루미늄(Al) 게이트, 텅스텐 게이트 MOSC를 제작하였다. 35$0^{\circ}C$에서 증착된 텅스텐 박막은 10~11$\Omega$/ 의 면저항을 가졌고 미소한 W(110) peak값을 나타내는 것으로 보아 비정질 상태에 가까웠다. TiN 박막의 경우 120~130$\Omega$/ 의 면저항을 가졌고 TiN (200)의 peak 값이 크게 나타난 반면, TiN(111) peak가 미소하게 나타났다. TiN 박막의 두께와 WF/SiH4의 가스비를 변화시켜가며 제작된 MOS 캐패시터를 HF 및 QS C-V, I-V 그리고 FNT를 통한 전자주입 방법을 이용하여 TiN 박막의 불소에 대한 확산 방지막 역할을 살펴 보았다. W/TiN 게이트 MOS 소자는 모두 순수 텅스텐 게이트보다 우수하였고, Al 게이트와 유사한 전기적 특성을 보여주었다. W/TiN 게이트 MOS 소자는 모두 순수 텅스텐 게이트보다 우수하였고, Al 게이트와 유사한 전기적 특성을 보여주었다. TiN 박막이 300 , 500 이고 WF6/SiH4의 가스비가 5:10인 경우 소자 특성이 우수하였으나, 5:5의 경우에는 FNT 전자주입 특성이 열화되기 시작하였다. 그리고, TiN박막의 두께가 150 으로 얇아질 경우에는 WF6/SiH4의 가스비가 5:10인 경우에서도 소자 특성이 열화되기 시작하였다. W/TiN 복층 게이트 MOS 캐패시터를 제작하여 전기적인 특성 분석결과, 순수 텅스텐 게이트 소자의 큰 저전계 누설 전류 특성을 해결할 수 있었으며, 불소확산에 영향을 주는 조건이 WF6/SiH4의 가스비에 크게 의존됨을 알 수 있었다. TiN 박막의 증착 공정이 최적화 될 경우, 0.1$\mu\textrm{m}$이하의 초미세소자용 게이트 전극으로서 텅스텐의 사용이 가능할 것으로 보여진다.