• 소성∙가공
• /
• 제7권5호
• /
• pp.445-449
• /
• 1998

In order to obtain optimum process variables during the drawing of stainless steel sheets rectangular cup drawing tests were carried out with several technically available stainless steel sheets. As parameters on testing materials for die and punches lubrication and blank holding forces were selected. Testing parameters played an important role if the deformed material was thin. Effect of material properties on the deformation behaviors was also discussed by using testing parameters selected in this experiment. From the test results we suggest the appropriate conditions to be applicable to the actual manufacturing processes

• 한국정밀공학회지
• /
• 제16권2호통권95호
• /
• pp.82-86
• /
• 1999

An experimental study has been carried out to reduce bending load, surface roughness and springback in bending process of stainless steel sheets. A U-bending test has been performed to investigate appropriate process parameters for getting better surfaces and accurate dimensions of stainless steel products. In the test, selected process parameters are die material, lubricant, and die clearance. Die materials used in the test are STD11(HRC60), STD11(TiCN), and AMPCO. From the test results, we can suggest that AMPCO dies are most suitable for reducing bending load and surface roughness of stainless steel sheets. And STD11 dies are favorable for avoiding spring-back in the stainless steel sheet-bending.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 2001년도 춘계학술발표회요약집
• /
• pp.290.1-290
• /
• 2001

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 춘계학술대회 논문집
• /
• pp.331-331
• /
• 2007

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2008년도 추계학술대회 논문집
• /
• pp.174-177
• /
• 2008

This paper replaces an conventional 300-austenitic stainless steel sheet to a 400-ferritic stainless steel for the cost reduction of a pulsator cover of a washing machine. However, ferritic stainless steel has poor formability in comparison with austenitic one. The low formability of ferritic steel results in problems during stamping such as fracture, wrinkling, shape inaccuracy and so on. Design modification of the stamping tool is carried out with the aid of the finite element analysis for multi-stage stamping process. The simulation results show that fracture occurs on top of the product while wrinkles are generated by the excess metal near the wing part. Modification of the initial stamping die is performed to improve metal flow and to eliminate problems during the stamping process. Simulation with the modified design fully demonstrates that safe forming is possible without inferiorities.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1995년도 추계학술대회논문집
• /
• pp.69-75
• /
• 1995

The deformation behavior of stainless steel-clad aluminum sheet metals under uniaxial tension has been investigated. The differences in mechanical properties such as elastic modulus, flow stress and plastic strain ratio, of component layers of the composite sheet gave rise to warping of the tensile specimens. The warping has been analyzed by FEM and the total force and momentum equilibria. The analyzed radii of curvature of the warped specimens were smaller than the measured data possibly due to elastic recovery during unloading. The differences in mechanical properties may also give rise to transverse stresses in the component layers. The transverse stresses have been analyzed on the assumption of isostrain and by the FEM in which the warping has been taken into account. The transverse stresses calculated by the FEM were lower than those by the isostrain hypothesis due to stress relaxation by the warping and turned out to be negligible compared with the longitudinal stresses. Consequently, the flow stresses of the composite sheets follow the rule of mixtures.

• 한국진공학회지
• /
• 제13권4호
• /
• pp.175-181
• /
• 2004

미소인장시험을 통해 304 스테인리스 스틸 판재 위에 증착된 DLC 박막의 안정성을 평가하였다. 모재의 소성 변형과 함께 코팅 층의 손상이 발생하기 시작하는데, 작은 규모의 모재 변형 시에는 인장축의 수직방향으로 박막의 균열이 발생하지만, 모재의 슬립변형이 발생하기 시작하면 인장 축과 $45^{\circ}C$의 각도를 갖는 슬립 면을 따라 필름의 박리가 발생하였다. DLC박막의 박리면적으로부터 필름의 접착력을 평가할 수 있었으며, 필름의 합성 전에 실시하는 Ar 플라즈마 스퍼터링 세척시간이 길수록 그리고 세척시 기판에 인가되는 전압이 높을수록 필름의 접착력은 향상되었다. 이러한 변화는 스테인리스 스틸 모재와 Si 접합 층간의 계면특성이 향상되면, 필름의 전체 접착력을 증진시킬 수 있음을 보여주고 있다.

• 대한기계학회논문집A
• /
• 제24권1호
• /
• pp.87-93
• /
• 2000

Warm, forming technique which is one of the new forming technologies to improve formability of sheet metal is applied to the cylindrical cup drawing of stainless-aluminum. clad sheets. In experiments the temperature of die and blank holder is varied from room temperature to 18$0^{\circ}C$, while the punch is cooled by circulation of coolant to increase the fracture strength of workpiece on the punch corner area. Test materials chosen for experiments are STS304-A1050-STS304, STS304-A1050-STS430 clad sheets and A1050-0 aluminum sheet. Teflon film as a lubricant is used on both sides of a workpiece. The limit drawing ratio as well as quality of drawn cups(distribution of thickness and hardness)are investigated and validity of warm drawing process is also discussed.

• 한국정밀공학회지
• /
• 제28권3호
• /
• pp.349-356
• /
• 2011

This paper replaces a conventional austenitic stainless steel sheet to a ferritic stainless steel for the cost reduction of a pulsator cover of a washing machine. However, ferritic stainless steel has poor formability in comparison with austenitic one. The low formability of ferritic steel results in problems during stamping such as fracture, wrinkling, shape inaccuracy and so on. Design modification of the stamping tool is carried out with the aid of the finite element analysis for multistage stamping process of the pulsator cover. The simulation results show that fracture occurs on top of the product while wrinkles are generated by the excess metal near the wing part. Modification of the initial stamping die is performed to improve metal flow and to eliminate problems during the stamping process. Simulation with the modified design fully demonstrates that safe forming is possible without inferiorities.