• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.7
• /
• pp.103-110
• /
• 2014

Recent TSV based 3D Integrated Circuit (IC) technology needs more powerful thermal management techniques. However, because cooling cost and form factor are restricted, thermal management are emphasis on software based techniques. But in case of throttling thermal management which one of the most candidate technique, increasing bus occupation induce total performance decrease. To solve communication bottleneck issue in TSV based 3D SoC, we proposed adaptive throttling technique Experimental results show that the proposed method can improve throughput by about 72% compare with minimal path routing.

• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.1516-1521
• /
• 2004

Mixing in Y-channel micro mixer is analyzed through computational fluid dynamics. In the case of passive mixing, we investigate the effect of geometric parameters on the mixing efficiency, such as shape of throttling geometry and angle between two inlets. Mixing performance improves as two fluids join not just horizontally but both vertically and horizontally, and it also improves when channel follows throttling shapes. A numerical results substantiate the highly efficient mixing performance. It is highly beneficial to fabrication process since the proposed throttling geometry is simple, but allows high mixing ratio.

• Proceeding of EDISON Challenge
• /
• 2016.11a
• /
• pp.68-70
• /
• 2016

최근 저비용 및 재사용 발사체 개발 연구에 관한 관심이 증가하고 있는 추세인데, 이로 인해 노즐 내부에 핀틀 개념을 적용하여 발사체의 성능을 높이거나 스로틀링을 활용한 재사용 연구가 중요해지고 있다. 이 노즐 내부에 탑재된 핀틀 형상은 노즐 성능을 결정짓는데 핵심적인 역할을 하게 된다. 따라서 본 논문에서는 핀틀 형상에 따른 압력특성과 재순환 영역의 경향성을 확인하여 추후 저비용, 재사용 발사체 개발 연구의 기초자료로 활용하고자 한다. 해석 결과 핀틀 크기보다 핀틀 각도가 성능 변화에 더 민감한 변수로 판단되었다.

• Aerospace Engineering and Technology
• /
• v.8 no.1
• /
• pp.82-97
• /
• 2009

In this study, a linearlized model of liquid rocket engine specifically for the gasgenerator cycle one was developed to serve as a basic control model. A commercial software Simulink was used for the modeling. Using this tool we studied the throttling characteristic of engine around its nominal mode. To obtain the effect of the throttle valve design on the engine's control characteristic, we included mathematical model of the control valve with driving motor and the pressure stabilizer which installed on the gas-generator fed line to sustain the mixture ratio of the gas-generator.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.1
• /
• pp.45-51
• /
• 2015

In order to meet the enforced emission regulations and reduce fuel consumption, various new technologies are employed in engines. The problem of NOx emissions under a lean mixture condition should be solved, because a lean-burn direct-injection engine can realize stable lean combustion with a stratified mixture, which results in improvements in fuel economy and emissions. This study investigated the effects of intake and exhaust valve timing changes on the performance and emission characteristics of a lean-burn LPG direct-injection engine. Under a partial-load operating condition without throttling, an increase in the intake valve opening led to an increase in NOx emissions due to an increase in the amount of excess air. The fuel consumption deteriorated with an increase in the exhaust valve opening due to a decrease in the expansion work and an increase in the pumping loss.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.46 no.6
• /
• pp.487-495
• /
• 2018

Experimental analysis of the spray characteristics of the movable sleeve injector, which can simultaneously control the area of the annular gap and the pintle gap, has been studied and a method for controlling the uniform performance over a wide thrust range has been studied. It is confirmed that the design flow rate is not satisfied when the constant pressure difference is set regardless of the opening distance of the sleeve. In order to improve this, the differential pressure in the annular gap and the pintle gap was applied differently according to the opening distance. It was confirmed that the design flow rate was satisfied within the operating range and thrust control was linear from 25% to 100% in linear sleeve area.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.2
• /
• pp.156-165
• /
• 2014

This paper is the first investigation on the effect of flow control methods on the part load performance in a spark ignition engine. For comparison of the methods, two control devices, port throttling and masking, were applied to a conventional engine without any design change of the intake port. Steady flow evaluation shows that steady flow rates per unit opening area and swirl ratio are very low compared with the port throttling and saturated from mid-stage valve lift, however, swirl increases slightly as the lift is higher in case of 1/4 masking control. In the part load performance, the effect of simple port throttling on lean misfire limit expansion is limited and insufficient; on the other hand a masking improves the limit considerably without any port modification for increasing swirl. Also the results show that the intake flow control improves the combustion with following two mechanisms: stratification induced by the combination of the flow pattern and the fuel injection timing attribute to ignition ability and the intensified flow ensure fast burn. In addition fuel consumption reduces under the flow controls and the reduction rate is different according to the operation conditions and control methods. At the Stoichiometric and/or low speed and low load the throttling method is more advantageous; however vice versa at lean and high load condition. Finally, the throttling is more efficient for HC reduction than masking, on the other side the NOx emissions increase under the masking and decrease under the port throttling compared with conventional port scheme.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.4
• /
• pp.121-130
• /
• 2014

This paper is the second investigation on the effects of intake flow control methods on the part load performance in a spark ignition engine. In the previous work, two control methods, port throttling and masking, were compared with respect to lean misfire limit, fuel consumption and emissions. In this work, the effects of these two methods on EGR characteristics were studied and simultaneously the differences between EGR and lean combustion as a dilution method were investigated. The results show that EGR limit is expanded up to 23% and 3 ~ 5% improvement in the fuel consumption are achieved around 8 ~ 13% rates by the flow controls comparing with 10% limit and 1.5% reduction around 3% rate of non-control case. The masking method is more effective on the limit expansion than throttling as like as lean misfire limit; however there is no substantial difference in fuel consumptions improvement regardless the control methods except high load condition. Also it is observed that there exist critical EGR rates around which the combustion performance and NOx formation change remarkably and these rates generally coincide with optimum rates for the fuel consumption. In addition, dilution with fresh air is much more advantageous than that of the exhaust gas from the view point of dilution limit and fuel consumption, while utilization of the exhaust gas is more effective on NOx reduction in spite of considerably small dilution compared with the use of fresh air. Finally, the improvement of fuel consumption by massive EGR is highly dependent on the EGR limit at which the engine runs stably, therefore the stratified combustion technique might be a best solution for this purpose.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• v.10 no.2
• /
• pp.59-63
• /
• 2005

가. 자율주행 트랙터가 작업하는 동안 작동상태를 효과적으로 모니터링하고 제어할 수 있도록 하기 위해 인터넷을 통한 자율주행 트랙터의 모니터링과 원격제어 기술에 대하여 시험 하였다. 나. 트랙터를 모니터링하고 제어하는 곳과 경작지가 있는 곳을 인터넷으로 연결하고, 운전자가 탑승하지 않은 트랙터는 인터넷을 통해 전달받은 명령을 수행하도록 액튜에이터를 제어하고 제어되는 상황을 경작지에 위치한 카메라가 촬영하여 인터넷을 통하여 원격지의 운전자 쪽으로 전송하도록 시스템을 구성했다. 다. HST 트랙터 조종장치로서 서보제어가 가능한 액튜에이터를 개발 장착하고 제어성능을 시험하였다. 전자유압제어(EHPS)식 조향액튜에이터는 , 조향가능각 100도의 전범위에 조향 제어가 가능했으며 전조향에 필요한 시간은 약 1.6초 정도 였다. 피스톤 펌프의 사판각을 제어하는 전후진 제어기는 리니어 모터 구동식으로 총 제어 변위 50mm를 이동하는데 제어시간이 약 1.2초 소요되었다. 엔진 회전수를 제어하기위한 스로틀 액튜에이터는 리니어 모터 구동식으로 제어변위 30mm에 대해 제어시간이 0.8초 소요되었다. 3점 링크에 부착된 작업기의 위치를 제어하는 리프트 제어기도 리니어모터로 구동하였으며 제어거리 40mm에 대해 제어시간 0.9초정도가 소요되었다 라. 제작된 HST 무인 트랙터를 인터넷과 무선통신 시스템을 이용하여 원격 모니터링과제어 가능성에 대해 시험 했다. 인터넷을 통한 장거리 원격제어 및 모니터링 시험에서 제어신호의 전달지연은 0.3 ${\sim}$ 0.5초정도로 제어신호의 피이드 백을 확인할 때까지는 약1초정도의 대기 시간이 필요한 것으로 나타나 모니터링 및 제어 시스템의 개발 시 이를 고려할 설계가 필요한 것으로 나타났다.된 표층수온 분포값보다 2005년 2월에 관측된 표층수온 분포값이 상대적으로 낮은 분포 특성을 나타내고 있었다. 따라서 인공위성자료를 이용한 황해의 2004년 해황 분석 결과는 이상수온 상승의 원인이 쿠로시오 해류의 변동과 관련성이 높다고 판단되며 이에 대한 지속적인 연구가 현재 진행중에 있다.에 인산염 처리, 여기에 초음파 처리, 마지막 단계로 3분 끓이면 억제율이 68%까지 억제되었다. 이는 단일처리시 전혀 억제를 못하는 처리를 단계별로 한 단계씩 더해가면 allergy 억제효과가 나타난다고 할 수 있겠다. 초음파 처리도 역시 저 allergy 처리 공정에 이용될 수 있는데 이것은 그 처리로 인해 새로운 알러젠이 생성될 수도 있다. 또한 복합처리로 allergy를 감소시키면 연속적이고 동시적으로 하기 때문에 원가를 절감할 수 있다.환경현안에 대한 정치경제적 접근을 외면하지 말고 교과서 저작의 소재로 삼을 수 있어야 하며, 이는 '환경관리주의'와 '녹색소비'에 머물러 있는 '환경 지식교육'과 실천을 한단계 진전시키는 작업으로 이어질 것이다. 이후 10년의 환경교육은 바로 '생태적 합리성'과 '환경정의'라는 두 '화두'에 터하여 세워져야 한다.배액에서 약해를 보였으나, 25% 야자지방산의 경우 50 ${\sim}$ 100배액 어디에서도 액해를 보이지 않았다. 별도로 적용한 시험에서, 토마토의 경우에도 25% 야자지방산 비누 50 ${\sim}$ 100배액 모두 약해를 발생하지 않았으나, 오이에서는 25% 야자지방산 비누 100배액에도 약해를 나타내었다. 12. 이상의 결과, 천연지방산을 이용하여 유기농업에 허용되는 각종의 살충비누를 제조할 수 있었으며, 방제가 조사결과 진딧물, 응애 등 껍질이 연약한

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.20 no.1
• /
• pp.146-159
• /
• 2021

vehicle simulator as part of an empirical analysis the driving characteristics of elderly drivers. To this end, the driving characteristics of the elderly driver from previous study review. he driving characteristics of the elderly the driving elderly driver and general driverIn summarizing these experimental results, the -test showed different driving characteristics from general drivers in all items except for one side of the lane, such as driving speed and driving operation (brake, throttle, steering operation) at a significance level of 95%. Second, when changing lanes, it was difficult for elderly driver to maintain speed and secure an appropriate distance between carslderly driver changed lanes even in inappropriate situations (short distances between cars). Third, in unexpected situation, elderly drivers needed more distance and time.