• Journal of Aquaculture
• /
• v.13 no.4
• /
• pp.317-323
• /
• 2000

Experimental cohorts of Mugil cephalus were divided into 5 groups : seawater~normal feed (SWN), acclimation to freshwater~normal feed (GFWN), acclimation to freshwater~salt feed (Gf\iVS), freshwater. normal feed (FWN) and freshwater-salt feed (f\iVS). Growth was faster in the SWN, Gf\iVS, and GFWN groups than in the f\iVS and FWN groups. Condition factor did not differ among the groups. Survival (92 %) of the juveniles was the highest in the Gf\iVS group; however, the others showed no significant difference. Moisture of FWN group was significantly higher than that of SWN group (P < 0.05). Potassium concentration was significantly higher in the SWN group than that of others (P < 0.05). It was highest (30 mmolfl) among the cohort of SWN.

• Journal of Energy Engineering
• /
• v.15 no.4 s.48
• /
• pp.277-283
• /
• 2006

In this study, butane 100% was used as fuel to verify the real fuel effect such as vapor pressure variation due to temperature change. A MPI fuel injection system for V-6 engine, which has reverse 'L' type cross section to minimize the possibility of liquid phase injection, was composed and one bank was operated under sequential injection scheme. Flow rate were measured according to injection duration, interval, and pressure. Also occurring of liquid phase injection was monitored with varying vaporizer and fuel rail temperature. The result shows that basic characteristics of injection is a relatively difference between air and LPG injection. Under cold start condition, however, the occurrence of liquid injection becomes more severe as the pressure increases, and sufficiently high temperature both in vaporizer and fuel rail is very important to insure gaseous injection. In addition, the temperature of vaporizer plays more important role in keeping LPG vapor state and the reverse 'L' type cross section of the rail is available to prevent liquid injection.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.5
• /
• pp.97-103
• /
• 1997

Effects of fuel injection timing on the lean misfire limit of a sequential MPI SI engine has been investigated. To investigate the interaction of injection timing and intake flow characteristics, so called axial stratification phenomena, 4 kinds of different intake swirl port of the same combustion chamber geometry have been teated in a single cylinder engine test bench. And 2 kinds of fuel, gasoline and compressed natural gas(CNG), were used to see the effect of liquid fuel vaporization. Result shows that combination of port swirl and injection timing governs the lean misfire limit and lean misfire limit envelopes remain almost the same for a given ratio regardless of engine speed. It is also found that two phase flow has some effects on lean misfire limit.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.3 no.6
• /
• pp.224-237
• /
• 1995

An ECU(Electronic Control Unit) with 16 bit microcomputer has been developed. This system includes hardware and software for more precise control on fuel injection, ignition timing, and idle speed. This control system employs an air flow sensor of the hot wire type, a direct ignition system, an idle speed control system using a solenoid valve, and a crank angle sensor. Especially, the crank angle sensor provides two separate signals: One is the position signal(POS) which indicates 180 degree pulses per revolution, and the other is the reference signla(REF) that represents each cylinder individually. The conventional engine control system requires at least two engine revolutions in order to identify the cylinder number. However, the developed engine control system can recognize the cylinder number within a quarter of an engine revolution. Therfore, the developed engine control system has been able to control fuel injection and ignition timing more quickly and accurately, Furthermore, the number of misfire reduces during the cold start.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.23 no.4
• /
• pp.444-453
• /
• 2015

In the previous study, several problems were observed in a NG conversion vehicle, which were fail of air-fuel ratio closed loop control, aggravated fuel economy, increased harmful emission and declined roadability. It was provisionally supposed that the mismatch of injection system with the engine caused these performance deterioration. In this context, the characteristics of fuel injection system of commercial conversion kit for NG were investigated experimentally varying the engine speed, fuel rail pressure and volume. The results are as follows; The injection quantity decreases as the engine speed increases due to the extremely small rail volume of the presenting system and flow rate of No. 2 injector are always lower than that of the other ones regardless of the speed under the dynamic operation condition. Furthermore the existing system does not meet the required fuel quantity for the normal engine operation over 3000 RPM. On the other hands, the large rail volume systems ease and/or eliminate the difference of injection quantity between the injectors according to the speed variation, however, these systems decrease injection flow rate and still cannot supply sufficient fuel. Finally, suitable combination of the higher rail pressure and the larger rail volume might be a solution about these problems.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.1578-1583
• /
• 2003

Time-Optimal solutions for attitude control with reaction wheels as well as with thrusters are studied. The suggested varying-time-sharing ratio thrusting is found to reduce the maneuvering time enormously. The hybrid control such as sequential hybrid and simultaneous hybrid with reaction wheels and thrusters are considered. The results show that simultaneous hybrid method reduces the maneuver time very much. Spacecraft model is KOrea Multi-Purpose SATellite(KOMPSAT)-II, which is being developed by KARI in KOREA as an agile maneuvering satellite.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1999.10a
• /
• pp.5-5
• /
• 1999

3단형 과학로켓(KSR-III)의 기본형 및 응용형에 공통으로 사용되는 주엔진은 액체산소를 산화제로, 케로신을 연료로 사용하는 액체추진기관이다. 엔진 기본설계를 통하여 로켓 임무 요구사항에 부합되도록 엔진 각 부분의 기본제원을 설정하였고, 엔진의 형상을 결정하였다. 설계된 엔진의 성능검증 작업은 분사시험용 엔진, 축소형 엔진, 엔지니어링 모델 및 비행시험모델의 설계/제작/시험을 통하여 순차적으로 수행할 계획이다. 본 연구는 3단형 과학로켓 엔진의 기본설계 및 성능검증 계획에 관한 것이다.

• The Bulletin of The Korean Astronomical Society
• /
• v.37 no.2
• /
• pp.163.2-163.2
• /
• 2012

다목적실용위성 3호는 2012년 5월 발사되어, 위성 기능점검을 위한 시험을 성공적으로 완료하였다. 위성이 발사체로부터 분리된 이후 임무궤도(고도 685km, 승교점 지방시 13시 30분을 갖는 태양동기궤도)를 획득하기 위해서는 궤도조정이 필요하다. 본 논문에서는 다목적실용위성 3호의 초기운영 기간 동안 수행한 총 10번의 궤도조정 계획 및 결과에 대해 기술하였다. 궤도조정 1 단계에서는 궤도조정 절차 및 기능을 점검하기 위해 6번의 시험 궤도조정을 순차적으로 수행하였고 이후 2 단계에서는 임무궤도 진입을 위해 4번의 궤도조정을 실시하였다. 궤도조정을 위해서는 원하는 추력분사 방향을 맞추기 위해 롤 방향 또는 피치 방향의 자세제어가 필요한데, 추력기를 사용하여 자세를 기동하는 모드(Del-V Mode)와 휠을 사용하여 자세를 기동하는 모드(Fine Del-V Mode)로 구분된다. 시험 궤도조정에서는 우선적으로 두 가지 모드에 대한 모드전환 시험을 실시하여 위성체 및 지상국 운영절차에 대한 이상 유무를 점검하였고, 이후 추력기 분사량을 10초로 설정하여 예측 대비 실제 궤도변경 결과값을 확인하였다. 시험 궤도조정의 결과를 토대로 본 궤도조정에서는 임무궤도를 획득하기 위한 경사각 조정 및 고도 조정을 수행하였다. 경사각 조정 시에는 승교점 지방시의 변화량을 줄이고, 이후 자연 교란력에 의한 궤도변화를 고려하여 목표궤도를 계획하였다. 또한, 고도 조정 단계에서는 연료 사용량 및 이심률 변화를 최소화 할 수 있도록 전형적인 호만 궤도천이 방식을 적용하였다. 궤도조정 결과 당초 목표한 값을 정확하게 달성하였고, 궤도조정 이후 궤도변화도 장기간 동안 임무궤도 범위를 유지함을 확인할 수 있었다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.10
• /
• pp.1001-1009
• /
• 2012

In this study, the cooling characteristics of combustion gas were investigated by injecting liquid nitrogen ($LN_2$) into a liquid rocket combustion chamber, which uses liquid oxygen (Lox) and kerosene as propellants. $LN_2$ injectors and an extended chamber for mixing were installed at the end of the ordinary LRE combustion chamber, and a nozzle was installed after the chamber for mixing. First, an ignition test of the liquid rocket engine was conducted to verify the stable combustion process. Next, a hot firing test was performed step-by-step for safety. Finally, the test was performed for 20 s. The results showed that the combustion gas of the LRE could be successfully cooled by using $LN_2$.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.3
• /
• pp.115-122
• /
• 1998

For digital engine control timings, such as ignition, are based on the crank shaft angle. Therefore, it is very important that the angle of the crank shaft can be detected with accuracy for optimal ignition timing. Sequential multi-point injection(MPI) systems that have independent injection events for each cylinder, are used to inject an accurate quantity of fuel, and to cope with varying engine status promptly. In this study the distributorless ignition timing. A crankshaft position sensor has been installed such that it generates a number of pulses per crankshaft revolution to permit accurate detection of the crank shaft angle. An event detecting algorithm has been developed, which detects the crank shaft pulses generated by the position sensor, and the software outputs the required control signals at given crank angle values. We clarified that the hardware method is the best way to increase the performance of the control system, because the event detecting duration T(1+2)max becomes zero.