• The Journal of the Acoustical Society of Korea
• /
• v.26 no.7
• /
• pp.343-352
• /
• 2007

The present study aims to investigate the design standard for acoustic criteria of Korean traditional music which could be used for the design of Korean traditional music halls. In order to do this, subjective listening tests were undertaken to musicians using auralized sounds which were convolved with the impulse response of traditional instruments recorded in an anechoic chamber. 94 pairs of sound were made which have different value of acoustic parameters including RT, BR, Brilliance, G, C80, ITDG, IACC. A paired comparison method(PCM) was used to analyze the results from the subjective listening tests. The results show that the preference of acoustic criteria for the Korean traditional music is far different from those of western music. As a result, specific range of acoustic criteria were suggested for the appropriate acoustic conditions of Korean traditional music. Also, a guideline of the acoustic design of halls for performing the Korean traditional music was suggested which could be used as a basic reference in the future works.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.49 no.9
• /
• pp.251-258
• /
• 2012

Recently, NAND Flash memory structure is evolving from SDR (Single Data Rate) to high speed DDR(Double Data Rate) to fulfill the high performance requirement of SSD and SSS. Accordingly, the proper ways of transferring data that latches valid data stably and minimizing data skew between pins by using PHY(Physical layer) circuit techniques have became new issues. Also, rapid growth of speed in NAND flash increases the operating frequency and power consumption of NAND flash controller. Internal voltage variation margin of NAND flash controller will be narrowed through the smaller geometry and lower internal operating voltage below 1.5V. Therefore, the increase of power budge deviation limits the normal operation range of internal circuit. Affection of OCV(On Chip Variation) deteriorates the voltage variation problem and thus causes internal logic errors. In this case, it is too hard to debug, because it is not functional faults. In this paper, we propose new architecture that maintains the valid timing window in cost effective way under sudden power fluctuation cases. Simulation results show that the proposed technique minimizes the data skew by 379% with reduced area by 20% compared to using PHY circuits.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.19-19
• /
• 2017

자율주행 트랙터를 위한 트랙터 조향제어는 일반적으로 전자모터를 이용한 EPS(Electric Power Steering) 시스템을 스티어링 휠에 연결하여 회전변위를 변경하고 그 결과 오비트롤(Orbitrol) 밸브의 토출유량을 바꾸고 호스로 연결된 조향실린더의 변위를 조절하여 최종적으로 전방 타이어의 방향각을 변경하면서 이루어진다. 이러한 조향방식은 시스템 구조상 조향실린더와 오비트롤 밸브가 상대적으로 멀리 떨어져 있으며, 밸브 특성상 약 ${\pm}5^{\circ}$의 오버랩이 포함되어 있다. 또한, EPS의 전자모터는 관성력, 마찰, 백래시 등의 영향을 가진다. 이와 같은 복합적인 영향은 조향 응답을 느리게 만들어 상대적으로 빠른 속도에서 주행에서 추종성능이 떨어지는 문제가 발생한다. 본 연구에서는 자율주행 트랙터의 조향성능 개선 연구의 일환으로 조향 HILS 시뮬레이터를 설계제작하여 조향 성능의 요인을 실험적으로 구명하고자 하였으며 이를 바탕으로 조향 시스템의 설계개선 방안을 수립하고자 하였다. 시뮬레이터는 동양물산 80 마력급 TX803 트랙터에 사용되는 오픈센터방식의 오비트롤 유압회로 시스템을 기어펌프가 장착된 AC모터로 구동되게 구성하였으며, 유량은 모터의 주파수를 조절 회전속도를 조절 변경하였다. 추가적으로 EPS와 오비트롤 조합의 조향성능을 비교 및 개선하기 위해 비례제어밸브(PVG 32, Danfoss)를 추가 장착하였다. 실제 트랙터 조향 시 나타나는 마찰저항을 모사하기 위해 부하 실린더를 구성하였으며, 조향 실린더의 부하의 크기는 부하 실린더를 폐회로를 구성하고 유량비례제어밸브를 이용한 유로의 개구량 조절을 통해 부하의 크기를 약 4000 N 까지 증가시킬 수 있도록 하였다. EPS와 비례제어밸브를 제어하기 위해 CANoe 8.0 소프트웨어를 이용하여 CAN통신 기반 가상 조향ECU를 구성하였으며 오비트롤의 기본 성능을 확인하기 위해 조향휠에 따른 실린더 동특성 및 계단 추종성능을 비례제어밸브와 비교하였다. 오비트롤 밸브는 약 ${\pm}5^{\circ}$이상 동작 시 실린더 압력이 상승하기 시작하였으며, 이후 약 ${\pm}10^{\circ}$이상 동작 시 조향실린더가 동작하기 시작하였다. 계단 추종성능실험에서는 비례제어밸브가 약 2배 이상의 응답개선을 나타냈다. 자율주행 경로추종 성능을 향상시키기 위해서는 순간적인 출력밀도가 높은 비례제어밸브를 통해 응답개선이 필요한 것으로 나타났다.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.39 no.3
• /
• pp.218-229
• /
• 2003

A new biotelemetry method that the installation and the treatment of equipment is convenient and the instantaneously detailed location of the fish attached the pinger is able to track comparatively easily was developed. The receiving system in this biotelemetry method was advanced for track the detailed behavior of the fish by the miniature tracking pinger, because it was a burden to fish to add the pinger with the water temperature and the pressure sensor. By combining of the super short base line (SSBL) method to detect the direction of pinger and the pinger synchronizing method to measure the range from receiving transducer to pinger, the three dimensional locations of fish to the receiving transducer is gotten instantaneously. The receiving system is devised to realize the high precision or wide detection range by application of the basic design method for receiving system of biotelemetry developed by the present authors and the hydrophone array configuration. The measurement distance error in the pinger synchronizing method is minimized through the correction of which the deviation of transmission pluse period of pinger is caused by changing water temperature. A prototype system which is able to track the instantaneously detailed location of the fish by the SSBL and pinger synchronizing biotelemetry (SPB) method was produced.

• Journal of Satellite, Information and Communications
• /
• v.12 no.4
• /
• pp.78-86
• /
• 2017

Japan has a lot of interest about weapons systems development of surrounding national and has invested heavily in securing intelligence assets to get information about them, because of conflict issues between Japan and Russia with four northern islands, China with Senkaku Islands and entry policy into the Pacific. Japan has used a large budget to detect and intercept ballistic missile for reasons of the launch of the Taepodong missile in 1998. After took over SIGINT equipments which U.S. force had operated in 1950s~1960s, Japan made a technological analysis and advanced IT technology to produce superior equipments. Japan's SDF has installed them in 19 locations across Japan. In addition, Japan's JASDF has installed advanced early warning RADAR to detect aircraft and high speed ballistic missile entering JADIZ with S-band in 28 locations across Japan. It is possible to detect missile launch preparations, engine tests, and launch moments at any time for operation of 6 satellites high resolution reconnaissance system and 6 aegis ships. In close cooperation with the US, Japan is accessible to the SBIRS networks which detects the launch of a ballistic missile in neighboring countries. In the future, Because the United States wants Japan to act as part of the United States in East, south Asia, it is believed that the exchange of intelligence on the surrounding countries between two countries will be enhanced.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.15 no.5
• /
• pp.95-107
• /
• 2016

The axle weight of a vehicle in motion can be measured with a low-speed or high-speed weigh-in-motion (WIM). However, the axial load dynamically change depending on the vehicle's characteristics-such as the chassis or axle structure-or the characteristics of the driving environment such as road flatness. The changes in dynamic load lead to differences between the vehicle's weight measured at rest and the vehicle's weight measured in motion. For this Study, an experiment was conducted with an instrumented vehicle to analyze the range of errors caused by uncontrollable environmental factors by identifying the characteristics of the dynamic load changes of a vehicle in motion, and determine the appropriate scale for the accuracy evaluation of a high-speed WIM, as a preparatory research for the introduction of unmanned overweight enforcement systems in the future. The key findings from the experiment are summarized as follows. First, The gross weight of the tested vehicle changed by approximately 1% at low velocities and approximately by 4% at high velocities, and the vehicle's axle weight changed by approximately 1-3%, at low velocities and by 2-9% at high velocities. A single axle showed larger weight changes than individual axles in a group. Secondly, The vehicle's gross weight and the axle weight on the impact section were up to eight times and three-to-twelve times higher, respectively, than its gross weight and the axle weight on the flat section. The vibration frequency of the vehicle's dynamic load was measured at between 2.4 and 5.8Hz, and found to return to the normal amplitude after moving approximately 30 meters.

• Journal of the Korean Society of Safety
• /
• v.12 no.4
• /
• pp.214-219
• /
• 1997

The mechanical seals, which are installed in rotating machines like pump and compressor, are generally used as sealing devices in the many fields of industries. The failure of mechanical seals such as leakage, crack, breakage, fast and severe wear, excessive torque, and squeaking results in big problems. To identify abnormal phenomena on mechanical seals and to propose the proper monitoring parameter for the failure of mechanical seals, sliding wear experiments were conducted. Acoustic emission, torque, and temperature were measured during experiments. Optical microstructure was observed for the wear processing after every 10 minute sliding at rotation speed of 1750 rpm and scanning electron microscopy was also observed. Except for the initial part of every experiment, the variation of acoustic emission was well coincided with torque variation during the experiments. This study concludes that acoustic emission and torque are proper monitoring parameters for the failure of mechanical seals. The intensity of acoustic emission signals is measured in root mean square voltage. Temperature of sealing face will be used as a parallel parameter for increasing the reliability of monitoring system.

• Journal of the Korea Society of Computer and Information
• /
• v.28 no.1
• /
• pp.49-54
• /
• 2023

The Global Positioning System (GPS) was developed for military purposes and developed as it is today by opening civilian signals (GPS L1 frequency C/A signals). The current satellite orbits the earth about twice a day to measure the position, and receives more than 3 satellite signals (initially, 4 to calculate even the time error). The three-dimensional position of the ground receiver is determined using the data from the radio wave departure time to the radio wave Time of Arrival(TOA) of the received satellite signal through trilateration. In the case of navigation using GPS in recent years, a location error of 5 to 10 m usually occurs, and quite a lot of areas, such as apartments, indoors, tunnels, factory areas, and mountainous areas, exist as blind spots or neutralized areas outside the error range of GPS. Therefore, in order to acquire one's own location information in an area where GPS satellite signal reception is impossible, another method should be proposed. In this study, IMU(Inertial Measurement Unit) combined with an acceleration and gyro sensor and a geomagnetic sensor were used to design a system to enable location recognition even in terrain where GPS signal reception is impossible. A method to track the current position by calculating the instantaneous velocity value using a 9-DOF IMU and a geomagnetic sensor was studied, and its feasibility was verified through production and experimentation.

• Asia-pacific Journal of Multimedia Services Convergent with Art, Humanities, and Sociology
• /
• v.8 no.6
• /
• pp.853-861
• /
• 2018

This paper proposes the application of harmonic constraints to address the problems caused by abnormal voltage increases when electric railway vehicles are running. The AC line that supplies the train with power during operation is used to provide electricity of 25kV/60 Hz, but gradually the size and frequency of harmonics involved in the line are varied with the technological evolution of the railroad vehicle electrical equipment. An increase in heat losses due to the failure of the instrument transformer (PT), the main circuit device, which is a serious problem with the recent train safety operation, or to the main displacement voltage. When high frequency components are introduced through low frequency Transformers of the main circuit device, the high intensity of the components is caused by the high intensity of the core and the current flow of the parasitic core is increased, thus generating heat. To solve this problem, the recent adjustment of the sequence has applied artificial NOTCH OFF of the power converter. However, the method of receiving and controlling the OFF signal operates by interaction between the ground and the vehicle's devices, thus it is invalid in the event of failure, and an actual accident is occurring. Therefore, the harmonic currents were required to prevent possible flow of harmonics, and conducted a study to prevent accidental occurrence of train accidents and to verify feasibility of the device through the simulations of the train's experimental analysis and the simulations of the train for safe operation.

• Cartoon and Animation Studies
• /
• s.36
• /
• pp.469-491
• /
• 2014

Webtoon has developed the method that makes it possible to express sound visually. Also we can also hear sound in webtoon through the development of web technology. It is natural that we analyze the sound that we can hear, but we can also analyze the sound that we can not hear. This study is based on 'dual code' in cognitive psychology. Cartoonists can make visual expression on the basis of auditive impression and memory, and readers can recall the sound through the process of memory and memory-retrieval. This study analyzes both audible sound and inaudable sound. Concise analysis owes the method to film sound theory. Three main factor, Volume, pitch, and tone are recognized by frequency in acoustics. On the other hand they are expressed by the thickness and site of line and image of sound source. The visual expression of in screen sound and off screen sound is related to the frame of comics. Generally the outside of frame means off sound, but some off sound is in the frame. In addition, horror comics use much sound for the effect of genre like horror film. When analyzing comics sound using this kinds of the method film sound analysis, we can find that webtoon has developed creative expression method comparing with simple ones of early comics. Especially arranging frames and expressing sound following and vertical moving are new ones in webtoon. Also types and arrangement of frame has been varied. BGM is the first in using audible sound and recently BGM composed mixing sound effect is being used. In addition, the program which makes it possible for readers to hear sound according to scroll moving. Especially horror genre raise the genre effects using this technology. Various methods of visualizing sound are being created, and the change shows that webtoon could be the model of convergence in contents.