• Food Science and Preservation
• /
• v.10 no.4
• /
• pp.506-511
• /
• 2003

DSC was used to investigate the thermal mechanism of acorn and corn starch with or without saccharides on gelation and retrogradation. When the samples were starch-saccharide-water system (s-s-w), from measuring of gelation enthalpy and temperatures of initial gelation, peak and conclusion(T$\_$0/, T$\_$p/, T$\_$c/), those of s-s-w system were higher than those of stank-water system (s-w). The retrogradation enthalpy of acorn starch and corn starch was straightly increasing by DSC measurement as storage times. This increase meant slowly becoming recrygtallization of amylopectin. In retrogyadation process, the starch-saccharide-water system's enthalpy was also increased. After 7 days went, the value of the enthalpy was steady. Saccharides were retarding retrogrodation because of stopping the recrystallization of amylopectin. Especially in using fructose and maltose, the retrogradation effect of maltose was well. These elements took effect the number of juntion zone, one of equatorial OH and dynamic hydration number. As these three elements were increasing, a starch-Rel-system was stabilizing.

• Resources Recycling
• /
• v.22 no.3
• /
• pp.36-42
• /
• 2013

According to the recent community-based structures enlargement, specification, and diversification. It needs appropriate construction materials in terms of intensity and environmental aspects. Thus, in manufacturing the cement using micro limestone powder which is main material. It is also expected to save energies and reduces $CO_2$, by using the blast furnace slag and fly ash which are mitigated environmental load construction materials that emerged. In this research, The durability aspect tries to be grasped considering the chemical property according to the coherence of the hydration product. Consequently, The compressive strength was measured over 30 Mpa on 3rd. In addition, according to the content of the limestone powder, the setting time is promoted. It has the feature expanded in the length change. And it is determined because the possibility of replacing the existing for construction material such as it is measured compared with the time to use the portland cement usually that flexural strength is high with the age 7 days ago, so it is sufficient.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.9 no.4
• /
• pp.650-657
• /
• 2021

Alkali activators that stimulate mineral compounds are expensive materials, but in order to replace industrial products of high alkali in gredien ts, both product an d econ omic feasibility must be satisfied. In this study, alkali in dustrial waste(LW) from the LCD man ufacturin g process were used for the purpose of alkali active reaction of GGBFS for high stren gth concrete over 50MPa. Concrete mixed with LW had reduced workability, but it had the characteristic of increasing compressive strength. Analysis using ACI 209 Compressive Strength Model Equation was made to compare the changes in strength coefficients according to LW mixing. The durability test of concrete, such as Chloride Penetration Resistance and carbonation resistance, also showed excellent performance. In the Adiabatic temperature rise test results, the concrete mixed with LW had the effect of accelerating the initial hydration heat. However, the final Adiabatic temperature rise was not significantly affected by the mixing of LW.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2023.05a
• /
• pp.422-422
• /
• 2023

최근 발생되고 있는 도시지역에서의 침수피해는 과거와는 다른 양상으로 발생되고 있으며, 이로 인해 많은 재산피해와 소중한 인명피해가 발생되고 있다. 도시지역의 침수피해는 다양한 원인에 의해 피해가 발생된다. 기후변화로 인해 발생되는 높은 강우강도의 집중호우로부터 도시 피복의 불투수화나 부족한 우수유출저감시설로 인한 침투비율의 감소에 따른 유출량의 증대, 짧은 도달시간으로 인한 빠른 하천수위의 상승, 빠른 하천수위의 상승으로 인해 발생되는 하수도의 만관에 따른 관수로화로 인한 역류 발생, 역류된 홍수류의 도시 내 저지대로의 유입, 최대 조위와 맞물려 발생되는 홍수류 배제의 어려움 등은 도시침수라는 결과를 제공하는 주요 원인으로 작동하고 있다. 이러한 현실은 도시지역에서의 침수대책의 수립에 있어 과거와는 다른 특정한 대책의 수립이 필요하다는 점을 시사해 주고 있다. 특히 도시침수를 발생시키는 주요 원인에 대한 개별적인 대책수립보다는 도시침수의 발생확률이 높은 지역에 대해서는 이러한 원인을 종합적으로 고려하여 이를 방어할 수 있는 효율적이고 실제적인 계획을 수립할 필요가 있다. 우리나라는 현재 행정안전부의 자연재해저감종합계획, 환경부의 특정하천유역치수계획 및 하수도정비기본계획을 기본으로 소하천정비기본계획, 하천기본계획 등 소관 부처를 달리하는 다양한 계획들을 수립하여 홍수로부터 귀중한 자산을 보호하려는 노력을 시행하고 있다. 이러한 계획들은 주로 홍수에 대비하고자 하는 특정 구조물의 설계를 중심으로 하고 있으며, 설계에는 항상 경제성의 개념이 수반되므로 설계용량을 초과하는 자연재해의 발생에 대해서도 홍수 발생에 대비하기 위해서는 홍수예보 및 재난대응체계의 운용과 같은 비구조물적인 대책도 매우 중요하게 활용되어야 한다. 이와 같은 현실에서 도시지역의 침수피해를 방지하기 위해서는 이제 과거와는 달리 개별법에 의해 수립되는 각종 계획들을 특정공간에 대해서 종합적으로 고찰하고 최적화하여 현실적이고 효율적인 하나의 계획으로 수립될 필요가 있으며, 하천을 중심으로 시행되고 있는 홍수예보와 유사한 도시침수예보와 같은 비구조물적 대책의 기술적 제고와 시행의 확산이 매우 시급한 실정이다. 본 연구에서는 최근 발의된 「도시하천유역 침수피해방지대책법(안)」의 경과와 이 법률에서 다루고 있는 주요 내용들을 살펴봄으로써 향후 우리나라가 지향해야 할 도시지역의 침수피해에 어떻게 대응해나가야 하는지에 관해 살펴보았다.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.19 no.4
• /
• pp.116-124
• /
• 2015

The objective of this study is to evaluate the effects of the replacement levels of grinded fly-ash on the repaired mortar based on a polymer. The main parameters are the curing temperature and replacement levels of grinded fly-ash. The curing temperature and the replacement levels of grinded fly-ash are varied at $40^{\circ}C$, $20^{\circ}C$ and $5^{\circ}C$, and between 0% and 35% of the total binder by weight, respectively. The flow in fresh mortar and compressive strengths according to ages, the relationship of stress-strain, elastic modulus and modulus rupture in hardened mortar, as well as scanning the electron microscopy and the X-ray diffraction of mortar, were measured, respectively. The test results showed that the flow, elastic modulus and modulus rupture are great in mortar specimens with 20~30% of the replacement levels of grinded fly-ash. In addition, compressive strengths according to ages were affected by the replacement levels of grinded fly-ash and the curing temperature indicated that the strength development ratio of mortar with 20% of the replacement levels of grinded fly-ash was greater than others. In the prediction of the compressive strength specified by the ACI 209 code, the strength development at an early and late age can be generalized by the functions of the replacement levels of grinded fly-ash and the curing temperature. In the analysis of scanning the electron microscopy and the X-ray diffraction, the number and intensity of peaks increased and the form of CSH gels on the surface of the particle of grinded fly-ash was observed.

• Journal of the Korea Concrete Institute
• /
• v.23 no.3
• /
• pp.265-272
• /
• 2011

Even though concrete is the most important material for building structures, its intrinsic gray color degrades urban esthetics. In order to improve this problem, coloring methods of mixing pigment in concrete batch and painting the surface of concrete surface have been tried. However, applications of the coloring methods in construction field are difficult due to high cost and low durability. Recently, acid stain agent is emerging as a new coloring method for concrete. It is able to apply a remarkably thin colored layer on a concrete surface from chemical reaction between acid and alkaline solutions. This study has examined the changes and variations of the surface layer of mortar specimen from chemical reaction of acid stained agents. The colors were changed into natural irregular stains according to aging. After the staining, no shape change was found from visible inspections. Microstructure of the colored surface applied with acid stained agent was much rougher than that of original mortar. When the colored layer was compared to original surface, crystals of hydrate such as $Ca(OH)_2$ and C-S-H gel were observed. Surface hardness was same or slightly higher in the colored layer. The value of pH was reduced by approximately 10%, weight contents of elements such as Ca, Si, and Al were low. In the chemical composition of the colored layer, the non-cement based elements of Mn, Cr, and Cu increased. Also, Fe and alkali elements of K and Na increased.

• Applied Chemistry for Engineering
• /
• v.22 no.5
• /
• pp.501-507
• /
• 2011

To develop environmental-friendly insulating composite materials, natural cellulose and porous ceramic balls were used as core materials and activated Hwangtoh was used as a binder. Various specimens were prepared with different water/binder ratios and core material/binder ratios. The physical properties of these specimens were then investigated through compressive strengths, flexural strengths, absorption test, hot water resistance test, pore analysis, thermal conductivity, and observation of micro-structures using scanning electron microscope. Results showed that the maximum compressive strength varied appreciably with the water/binder ratios and core material/binder ratios, but the flexural strength increased with the core material/binder ratios regardless of water/binder ratios. The compressive strength and the flexural strength measured after the hot water resistance test decreased remarkably compared to those measured before test. The pore analysis measured after the hot water resistance test showed that total pore volume, porosity and average pore diameter decreased, while bulk density increased by the acceleration of hydration reaction of binder in the hot water. The thermal conductivity decreased gradually with an increase of core material/binder ratios. It can be evaluated that the composite insulation materials having good insulating properties and mechanical strengths can be used in the field.

• Journal of the Korea Concrete Institute
• /
• v.25 no.3
• /
• pp.339-345
• /
• 2013

This study is to derive from the required performances and the optimum mix proportion of the roof concrete placed in the in-ground LNG storage tank with a capacity of 200000 $m^3$, and propose the actual data for site concrete work. The concrete placing work without sliding and segregation in the fresh concrete condition is very important because the slope of domed roof is varied in the large range by its curvature. Also the control of hydration heat and the strength development at test ages are classified with massive section about 1.4 m thick and considered to the pre-stressing work and removal of air support after concrete placing work. Considering above condition, slump range is selected $100{\pm}25$ mm under the slope $20^{\circ}$ and $150{\pm}25$ mm over the slope $20^{\circ}$ s until 60 minutes of elapsed time. Also, the roof concrete is satisfied with compressive strength range including design strength at 91 days (30 MPa), pre-stressing work at 7 days (10 MPa), air support removal work at 21 days (14 MPa). Replacement ratio of limestone powder is determined by confined water ratio test and main design factors include water-cement ratio (W/C), sand-aggregate ratio and dosage of admixture. As test results, the optimum mix proportion of the roof concrete used low heat cement is as followings. 1) Replacement ratio of limestone powder 25% by confined water ratio test 2) Water-cement ratio 57.8% 3) Sand-aggregate ratio 42.0%. Also, test results for the adiabatic temperature rising test is satisfied with its criteria and shown the lower value compared to preceding storage tank (TK-13, 14). These required performances and the optimum mix proportion is to apply the actual construction work.

• Journal of the Korea Concrete Institute
• /
• v.26 no.1
• /
• pp.63-70
• /
• 2014

This experimental study was intended to improve the compressive strength of multi-walled CNT reinforced cementitious composites with efficiency. The variables considered are the degree of sonication, the amount of surfactant, the replacement ratio of silica fume, etc. Optical microscope informed that fiber dispersion of CNT was improved with the increase of sonication time, and the compressive strength was proved to be enhanced as the degree of sonication increased. When superplasticizer as a surfactant had SP/CNT ratio of 4~6, the best improvement in strength was obtained. Silica fume was shown to produce the highest compressive strength at 10% replacement. Microstructure of CNT composites was also analyzed; XRD and SEM results indicated that CNT addition hardly changed hydration products and microstructure, and MIP analysis found the reduction of total porosity as well as the increase of nano-pores with the size of tens of nm instead of the decrease of pore distribution in the region of around 10 ${\mu}m$ and 100 nm. The results of microstructure analysis explains that the strength improvement is closely related to physical contribution rather than chemical influence by adding CNT.

• Korean Journal of Soil Science and Fertilizer
• /
• v.34 no.4
• /
• pp.237-244
• /
• 2001

Investigation on the surface charge properties of some Korean arable soils was performed by ion adsorption technique with two kinds of indifferent ion ($Na^+$ and $K^+$) at the range of pH 3 to 9 in bulk solution. The contribution of soil components(organic matter, oxides and clay mineral) on the surface charge density was determined at two soil depth with different solid particle composition When the pH of solution increased, the negative charge of soil surface was increased among the all soils, but positive charge were not appeared above pH 6. apparently. The magnitude of surface charge density measured by NaCl adsorption method showed ra nges of $0.01{\sim}2.84cmol_c{\cdot}kg^{-1}$ and $7.41{\sim}12.20cmol_c{\cdot}kg^{-1}$ at pH 3 and pH 9, respectively. Ion adsorption method using KCl as index ion overestimated than the method using NaCl as index ion. The content of organic matter is the strongest factor on the value of dCEC/dpH.