• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2016.05a
• /
• pp.110-112
• /
• 2016

In this paper, the captive model test of submerged body using RA test was carried out at the Square Basin. The target model is a submarine with four different types. For the comparison between theory and measurement, hydrodynamic coefficients are calculated according to the described method and compared with RA measurements on Submarine models. in addition, horizontal stability index of underwater vehicle was checked.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.49 no.11
• /
• pp.103-109
• /
• 2012

Samsung Thales has developed a small-sized autonomous underwater vehicle "BOTO" verified by a mathematical model simulation. The hydrodynamic coefficients and drag force were experimented at circulating water channel for validating cruising performance of the AUV. Based on the mathematical model, we simulated turning radius and way-point tracking on horizontal plane using way-point tracking algorithm. In this paper we introduce the vehicle system and the sea trial test results will be shown.

• Journal of Navigation and Port Research
• /
• v.41 no.6
• /
• pp.389-394
• /
• 2017

In this paper, the captive model test of a submarine using the RA test was carried out in a square basin. The target model submarine consisted of four types varying according to the position of conning tower and control planes. Hydrodynamic derivatives were acquired by multi-regression analysis. As a result, horizontal dynamic stability indexes of the four types presented positive values and satisfied dynamic stability requirements. In addition, the stability index of type 1 and type 4 - each with the same cruciform configuration of the aft planes - scored within the acceptable range of motion stability.

• Journal of the Society of Naval Architects of Korea
• /
• v.51 no.6
• /
• pp.539-547
• /
• 2014

Ship squat is a well known phenomenon, which means an additional sinkage and a change of trim when a ship sails in shallow water. As a series of ship squat study, a HPMM(Horizontal Planar Motion Mechanism) test of KVLCC2 model ship to measure a sinkage and a trim in shallow water was conducted. Additionally a CFD(Computational Fluid Dynamics) analysis was carried out to simulate fluid flows around the ship surface. A change in ship speed, drift angle at three depth conditions(H/T = 1.2, 1.5 & 2.0) is considered for comparing these results. As a result, an increase of the ship speed and the drift angle caused an increase in ship squat in EFD(Experimental Fluid Dynamics), and created a lower pressure on the ship bottom area in CFD. Lastly the sinkage results of KVLCC2 by EFD and CFD are compared to results by three empirical formulas. The tendency of sinkage by EFD and CFD is similar to the results of empirical formulas.

• Journal of the Society of Naval Architects of Korea
• /
• v.51 no.1
• /
• pp.34-41
• /
• 2014

When a ship sails in shallow water, it is well known that an additional sinkage and trim of the ship(squat) is caused by change of hydrodynamic force between the seabed and the bottom of a ship. In this paper, to examine this phenomenon by model tests, the squat of KCS model ship at a low speed is measured by the vision based ship motion measurement system during HPMM tests. Various combinations of a ship speed, a rudder angle and a drift angle were tested at three depth conditions(H/T = 1.2, 1.5 & 2.0). As a result, increase of the ship's speed and ship's drift angle caused an increase in ship squat, but the ship's rudder angle did not. The rate of increase in ship squat was the most at H/T = 1.2 condition. Lastly these experimental results are compared to the results by three empirical formulas and two CFD methods. The tendency of ship squat measured by experiment is similar to those of empirical formulas.

• Journal of the Society of Naval Architects of Korea
• /
• v.59 no.5
• /
• pp.262-270
• /
• 2022

The emergence of new concept ships, such as autonomous ships, has drawn much attention on the manoeuvrability of ships because of the safe navigation and operation of ships. Although the manoeuvrability of KRISO Container Ship(KCS) has been frequently reported, there have been few documents of representative manoeuvre cases conducted in various methods by one institute. This paper presents the manoeuvrability of the ship in 1/42.0 model scale by 3 methods: free running model tests, horizontal planar motion mechanism tests, and computational fluid dynamics analysis. KRISO reports KCS manoeuvre data: 35° turning circle tests and 20/20(10/10) zigzag manoeuvring tests. In addition, a simple formula for integrating and comparing manoeuvre indices, Manoeuvrability Comparing Simple Index(MCSI), is proposed.

• The Journal of Korean Academy of Prosthodontics
• /
• v.57 no.2
• /
• pp.110-117
• /
• 2019

Purpose: This study was to evaluate the wear resistance of 3D printed, milled, and conventionally cured provisional resin materials. Materials and methods: Four types of resin materials made with different methods were examined: Stereolithography apparatus (SLA) 3D printed resin (S3P), digital light processing (DLP) 3D printed resin (D3P), milled resin (MIL), conventionally self-cured resin (CON). In the 3D printed resin specimens, the build orientation and layer thickness were set to $0^{\circ}$ and $100{\mu}m$, respectively. The specimens were tested in a 2-axis chewing simulator with the steatite as the antagonist under thermocycling condition (5 kg, 30,000 cycles, 0.8 Hz, $5^{\circ}C/55^{\circ}C$). Wear losses of the specimens were calculated using CAD software and scanning electron microscope (SEM) was used to investigate wear surface of the specimens. Statistical significance was determined using One-way ANOVA and Dunnett T3 analysis (${\alpha}=.05$). Results: Wear losses of the S3P, D3P, and MIL groups significantly smaller than those of the CON group (P < .05). There was no significant difference among S3P, D3P, and MIL group (P > .05). In the SEM observations, in the S3P and D3P groups, vertical cracks were observed in the sliding direction of the antagonist. In the MIL group, there was an overall uniform wear surface, whereas in the CON group, a distinct wear track and numerous bubbles were observed. Conclusion: Within the limits of this study, provisional resin materials made with 3D printing show adequate wear resistance for applications in dentistry.