• Tunnel and Underground Space
• /
• v.24 no.2
• /
• pp.176-186
• /
• 2014

Roughness, aperture and filling material of rock joint are widely considered to affect the hydraulic characteristics of joint. Among these factors, in this study, the joint roughness was examined with artificial joint profiles generated by Monte Carlo simulating on the original profiles suggested by Barton and Choubey(1977). Original profiles and revised profiles were combined to establish flow channel models, in which the hydraulic characteristics were analyzed numerically on the basis of minimum aperture changes and flow channel shapes. Maximum flow rate was identified at the growing point of flow area after passing through minimum aperture generated by the two profiles, and it was resulted that maximum flow rate is inversely proportional to minimum aperture. Maximum flow rate per unit area showed different values because flow channel shapes and minimum aperture locations are different in each model. In flow channel, mechanical aperture showed approximately 1.07 ~ 3.00 times larger than hydraulic aperture. In this study, mechanical and hydraulic aperture were concluded to be closely related to $A_i$ value, and their relations can be denoted by $e_m=0.519A^{0.7169_i}$ and $e_h=0.6182A^{0.239}_i$, respectively.

• Journal of Biomedical Engineering Research
• /
• v.25 no.6
• /
• pp.489-496
• /
• 2004

Insertion of cannulae into vessels may disturb the blood flow doing non-physiological load and stress on blood cells such that ADP may increase and result in hemolysis. Authors used the computational method to simulate the 3-dimensional blood flow inside of the cannula using numerical method. We limited the research to within the drainage cannulae with side holes inserted through the human vein. In this paper, 9 different cannulae with side holes categorized by the number of side holes of 4, 12, and 20, and also categorized by the array type of side holes of staggered array, in-line array, and alternative in-line array were studied and compared to the cannula with no side holes by using CFD analysis. We evaluated the flow rate, the wall shear stress, and the shear rate and compared them with one another to estimate the effect of the side holes. The flow rate is not proportional to the number of the side holes. However, larger number of side holes can reduce the mean shear rate. Both the number and the array type of side holes play an important role on the fluid dynamics of the blood flow in cannulae.

• Transactions of the Korean hydrogen and new energy society
• /
• v.22 no.3
• /
• pp.363-371
• /
• 2011

In this paper, a three-dimensional hydrogen desorption model is developed to precisely study the hydrogen desorption kinetics and resultant heat and mass transport phenomena in metal hydride hydrogen storage vessels. The metal hydride hydrogen desorption model, i.e. governed by the conservation of mass, momentum, and thermal energy is first experimentally validated against the temperature evolution data measured on a cylindrical $LaNi_5$ metal hydride vessel. The equilibrium pressure used for hydrogen desorption simulations is derived as a function of H/M atomic ratio and temperature based on the experimental data in the literature. The numerical simulation results agree well with experimental data and the 3D desorption model successfully captures key experimental trends during hydrogen desorption process. Both the simulation and experiment display an initial sharp decrease in the temperature mainly caused by relatively slow heat supply rate from the vessel external wall. On the other hand, the effect of heat supply becomes influential at the latter stages, leading to smooth increase in the vessel temperature in both simulation and experiment. This numerical study provides the fundamental understanding of detailed heat and mass transfer phenomena during hydrogen desorption process and further indicates that efficient design of storage vessel and heating system is critical to achieve fast hydrogen discharging performance.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.7
• /
• pp.3518-3527
• /
• 2013

The new developed train(HEMU-430X) faces running at high speed over 400km/h. But The Korea railway design code gives guidelines below 350km/h speed. Honam HighSpeed Railway was also designed based on the design standard below 350km/h. Existing infra structures have to be reviewed at high speed running and the design guideline for the speed over 350km/h should be prepared as soon as possible. This paper presents (1) the simulation results of composite steel girder bridge(Kaya Bridge of Seoul-Pusan HighSpeed Railway), (2) values measured at this bridge and the comparison with simulation results, and (3) the prediction of Yonjung bridge being constructed in Honam HighSpeed Railway.

• Journal of Engineering Education Research
• /
• v.3 no.1
• /
• pp.12-20
• /
• 2000

In this paper, we are trying to explain an education method using the studio class where a lecturer can teach the theoretical approach for goals of theme, simulation for the theoretical results by using commercial CAD tools, and experiments for the simulation and design results. In order to apply the education skill using studio class to electrical engineering field efficiently, the theoretical approach, simulation procedure, and experiments should be coincided with each other. In this paper, the design procedure of low pass filter for undergraduate and graduate is chosen as an example of studio class In order to show the validity of the proposed education method. By considering the example, the efficiency of the method will be discussed.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.7
• /
• pp.532-539
• /
• 2018

A position estimation technique is presented for a missile using high-resolution range profiles obtained by three wideband radars. Radar measures a target range using a reflected signal from the surface of a missile. However, it is difficult to obtain the range between the radar and the origin of the missile. For this reason, the interior angle between the moving missile and tracking radar is calculated, and a compensated range between surface of the missile and its origin is added to the tracking range of the radar. Therefore, position estimation of a missile can be achieved by using three total ranges from each radar to the origin of the missile. To verify the position estimation of the missile, electromagnetic numerical analysis software was used to prove the compensated range according to the flight position. Moreover, a wideband radar operating at 500-MHz bandwidth was applied, and its range profile was used for the position estimation of a missile.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.5
• /
• pp.2086-2091
• /
• 2013

One of the most important objects for the industrial ventilation is to protect worker's health from the harmful substances. Mainly in industrial ventilation, the harmful substances broken out through manufacturing process are to be quickly emitted outside. Recently the importance of the industrial ventilation increases with the recognition change of industrial ventilation from manufacturing focusing to human focusing. In this paper, the air flow simulation inside the coating room is performed. All the coating room and the ventilation system are modeled by SolidWorks program and air flow distribution and ventilation performance are analyzed by Flow simulation program. And the air flow directions and the air flow velocities inside the coating room are enhanced with the use of local ventilation.

• The KIPS Transactions:PartA
• /
• v.14A no.2
• /
• pp.125-132
• /
• 2007

Recently, in the engineering area, there is an increasing need for researchers at a distance to share the result of the experiment, without having to visit the experiment facilities. Especially in the civil engineering, researchers feel the need for participating in a experiment conducted at a distant location. In addition, it is suggested that high-cost facilities should be used by remote researchers thereby increasing the utilization rate. This paper proposes a remote experiment environment in civil engineering that are being developed in a project called Korea Construction Engineering Development(KOCED), which connects major civil engineering experiment facilities using grid technology, allows researchers to participate in a remote experiment, and has the experiment results shared by remote researchers automatically. Then, based on the suggested environment, we designed a hybrid test facility that involves two physical experiment facility sites and one numerical simulation site that are geographically apart. Then, we implemented its prototype and ran some tests, which showed a possibility of grid-based civil engineering experiment.

• Journal of the Korean Society for Railway
• /
• v.12 no.6
• /
• pp.829-834
• /
• 2009

A ballast-flying probabilitie is suggested for various ballast types, heighter types and underbody flow conditions as train speeds. The average speed of measured points is converted to the ballast-flying probabilities of BFPF which come from wind tunnel test data. Underbody flow fields are numerically simulated for the various conditions. The results show that the ballast-flying probability is steeply increased as train speed increased, and reaches a value of 87% at 350 km/h train speed. And the differences of probabilities among the ballast shapes are considerably high. The upper surface of heighter or tie is most probable area. Through this study, the ballast-flying Sensitivities with heighter was defined to understand the characteristics of ballast-flying probability on various conditions. And the ballast-flying probability can be reduced by the heighter.

• Journal of Advanced Marine Engineering and Technology
• /
• v.36 no.1
• /
• pp.118-125
• /
• 2012

In this paper, an approach to designing controllers for the tension/movement control of working robot to install a stringing wire cable is presented. To design a controller, when the robot moves a certain distance maintaining constant tension, the dynamic model of a stringing wire cable which considers effects of weights according to changing lengths is presented. Also the tension at startup of the working robot is studied by numerical analysis which is based on the equation of the dynamic wire model. From the dynamic model for a stringing wire cable, working robot for tension/movement control is suggested and designed a feedforward controller with a accelerator gain to suppress a mutual interference of the both tasks of tension/movement control. Depending on the operating conditions of the working robot, the effectiveness of the suggested system has been verified by the simulation and experimental results.