• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.23 no.6
• /
• pp.740-747
• /
• 2019

In this paper, an antenna applicable to WLAN and WiMAX frequency bands is designed, fabricated, and measured. The proposed antenna is designed to have two branch strip line in the patch plane and a rectangular slit in the ground plane based on microstrip feeding for triple band characteristics and added a vertical strip in the ground plane to enhance impedance bandwidth characteristics. The proposed antenna is designed on a substrate with a relative permittivity of 4.4, a thickness of 1.0 mm, and has a size of $18.0mm(W1){\times}37.3mm$ (L4+L5+L7). From the fabricated and measured results, impedance bandwidths of 480 MHz (2.32 to 2.80 GHz) for 2.4/2.5 GHz band, 810 MHz (3.22 to 4.03 GHz) for 3.5 GHz band, and 1,820 MHz (5.05 to 6.87 GHz) for 5.0 GHz band were obtained based on the impedance bandwidth. Measured 3D pattern and gains are displayed.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.11 s.114
• /
• pp.1040-1049
• /
• 2006

A design method for minimizing transmission loss of a broadband right-angle transition from a coaxial cable to a microstrip line is presented. The right-angle transition has been widely used where printed circuit applications need to be fed from behind the ground plane using coaxial line. To obtain the minimized transmission loss over the whole operating frequency range of the transition, design parameters such as ground aperture and probe diameters, ground aperture offset, and stub length are optimized using a commercial electromagnetic simulation software. Results are presented for the optimum right-angle transition from an SMA connector to a microstrip line on common reinforced 0.787 mm thick PTFE substrates. Measurements of a fabricated transition show that reflection coefficient is less than -22 dB and insertion loss is less than 0.45 dB over $0.05{\sim}20GHz$.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.6 s.97
• /
• pp.632-643
• /
• 2005

This paper presents a folded stripline-fed small broadband disk-loaded monopole antenna with vertical ground plane. The bandwidth of the proposed antenna can be enhanced by electromagnetic coupling between the shorted rectangular disk and the probe with folded strip line. The measured impedance bandwidth of the proposed antenna is $37.6\%$ for $VSWR\leq2$ with the center frequency at 2.313 GHz and has the physical dimensions of only $11mm\times11mm\times11mm$ which corresponds to the electrical length of $0.085\lambda_0\times0.085\lambda_0\times0.085\lambda_0$. For improving the radiation pattern characteristics, rectangular slits are inserted in the vertical ground plane. Rectangular slits affect the currents distribution on the ground plane, so that the antenna radiation in the direction of the ground plane is reduced more than 3 dBi. Gain of the antenna is approximately 2.6 dBi within the bandwidth.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.7
• /
• pp.796-808
• /
• 2007

In this paper, two novel compact microstrip bandstop filters using complimentary split ring resonators(CSRRs) and spiral resonators is proposed. The first one is the bandstop filter using an array of CSRRs etched on the center line of a microstrip. The bandstop is due to the presence of negative effective permittivity and positive permeability near resonant frequency which prevent the wave propagation. The second on is the bandstop filter using an array of spiral resonators etched on the center line of a microstrip. The bandstop is due to the self-resonance of spiral circuit. We have achieved controllable resonance frequency and bandwidth, super compact dimension, low insertion losses in the passband and high level of rejection in the stopband with sharp cutoff. The electrical sizes of two proposed filter are very small. Additionally, they can be easily fabricated and compatible with MMIC or PCB technology.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.26 no.7B
• /
• pp.895-900
• /
• 2001

본 논문에서는 하나의 급전선을 갖는 원형 섹터 마이크로스트립 안테나를 사용하여 서로 수직한 편파 특성을 갖는 이중주파수 안테나를 설계하였다. 여기되는 모드 및 주파수를 공진기 모델을 사용하여 계산하였으며, 반경과 섹터 각도를 파라미터로 하여 여기되는 두 주파수를 설계할 수 있었다. 약 2GHz 대역에서 동작하는 안테나를 제작하여 안테나의 특성을 측정하였다. 안테나의 반경을 고정하고 섹터 각도를 75$^{\circ}$에서 120$^{\circ}$까지 변화시켜, 여기되는 두 주파수의 비가 1.08에서 1.518까지 변하는 것을 볼 수 있었다.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.33 no.2
• /
• pp.111-122
• /
• 2015

This study purposed on introducing a new automated solution for detecting railway tracks and reconstructing track models from the mobile laser scanning data. The proposed solution completes following procedures; the study initiated with detecting a potential railway region, called Region Of Interest (ROI), and approximating the orientation of railway track trajectory with the raw data. At next, the knowledge-based detection of railway tracks was performed for localizing track candidates in the first strip. In here, a strip -referring the local track search region- is generated in the orthogonal direction to the orientation of track trajectory. Lastly, an initial track model generated over the candidate points, which were detected by GMM-EM (Gaussian Mixture Model-Expectation & Maximization) -based clustering strip- wisely grows to capture all track points of interest and thus converted into geometric track model in the tracking by detection framework. Therefore, the proposed railway track tracking process includes following key features; it is able to reduce the complexity in detecting track points by using a hypothetical track model. Also, it enhances the efficiency of track modeling process by simultaneously capturing track points and modeling tracks that resulted in the minimization of data processing time and cost. The proposed method was developed using the C++ program language and was evaluated by the LiDAR data, which was acquired from MMS over an urban railway track area with a complex railway scene as well.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.4
• /
• pp.498-505
• /
• 1999

The ferrite device that has nonreciprocal characteristics has been used as various microwave components. In this paper, the spectral-domain method was used to analyze the characteristics of structure(strip line on multilayer structure with ferrite material) for which no paper has been published yet. It is assumed that an external dc magnetic field is applied perpendicular to the ground conductor. The propagation constant is calculated for each parameter and frequency. Also we considered convergence by increasing the number of basis functions and verified the numerical analysis results. From the results, we could confirm that as the thicknesses of YIG is increased, the cutoff region is widened and the propagation constant is decreased at the frequency of upper cutoff region. For a larger applied dc magnetic field, the frequency of cutoff region is found to be increased. Also the simulation results for strip line show that the cutoff region is widened and the propagation constant is larger than that of microstrip line.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.7 s.98
• /
• pp.661-670
• /
• 2005

In this paper, the microstrip $90^{\circ}$ hybrid to provide -3dB coupling and $90^{\circ}$ phase difference at broadband frequency range of 2 to 6 GHz is designed. This proposed hybrid is composed of 3-section. The two outside section are realized by symmetrical edge coupled lines, but on the other hand the middle section consists of VIP(Vertically Installed Planar) circuit. The ground part of VIP circuit is partially removed to get tight coupling, particularly. This hybrid is easy to realize due to microstrip structure and has good holing flexibility by taking advantage of VIP circuit as a control point of optimization. The proposed hybrid provide satisfactory performance as compared with simplicity of structure and fabrication first of all.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.37 no.3
• /
• pp.35-42
• /
• 2000

A cross-shaped microstripline-fed printed slot antenna having wide bandwidth Is presented in this paper. The proposed antenna is analyzed by using the Finite-Difference Time-Domain (FDTD) method. It was found that the bandwidth of the antenna depends highly on the length of the horizontal and vertical feedline as well as the offset position of the feedline. The maximum bandwidth of this antenna is from 1.975 GHz to 4.725 GHz, which is approximately 1.3 octave, for the VSWR $\leq$ 2. Experimental data for the return loss and the radiation pattern of the antenna are also presented. and they are in good agreement with the FDTD results.e FDTD results.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2006.05a
• /
• pp.637-640
• /
• 2006

In this paper, a microstrip antenna with a small loop consisting of the left and right parallel plate to load capacitor is proposed. It is obtained the improved small size than the antenna of the transformed Uh and the antenna of the left and right parallel plate to load capacitor on QMSA. Equivalent circuit of transmission line model is designed to find more accurate resonant frequency. Also, the designed and fabricated antenna can receive both vertically and horizontally polarized waves to operating frequency of 1.5GHz. Therefore proposed antenna is available as a small antenna for wireless communication and will be quite useful for indoor communication