• Journal of the Korean Magnetics Society
• /
• v.3 no.3
• /
• pp.208-214
• /
• 1993

In order to investigate the origin of an increase in the coercivity with the Ta addition to Co-Cr films, the perpendicular magnetic anisotropy of Co-Cr film and CoCrTa film was measured by a torque magnetometer and VSM. In Co-Cr binary alloy film, the uniaxial anisotropy increased with increasing Cr content. The perpendicular magnetic anisotropy of $Co_{81.7}Cr_{16.7}Ta_{1.6}$ film was larger than that of $Co_{81}Cr_{19}$ film, both of which were deposited at the same substrate temperature of $100^{\circ}C$. The change in the perpendicular magnetic anisotropy with annealing was studied to understand the Ta addition effect. The amount of decrease in perpendicular magnetic anisotropy of the CoCrTa film by the annealing was larger than that of Co-Cr film. And the perpendicular magnetic anisotripies of Co-Cr film and CoCrTa film after annealing were almost the same. The cause of this was interpretated as the enhanced segregation of solute atoms in the Ta added thin film in the as-deposited state. The enhanced segregation of solute atoms increases the perpendicular magnetic anisotropy of the film, and causes the increase of perpendicular coercivity of the film.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.04a
• /
• pp.848-851
• /
• 2008

유리섬유 및 폴리에스테르와 같은 섬유질 흡음재의 단점을 보완하기 위하여 다공성 알루미늄과 같은 강체 흡음재가 개발되고 있다. 본 연구에서는 스테인리스 스틸을 이용한 다공성 강체에 대하여 수직입사 흡음성능을 조사하였다. 밀도, 두께, 세부 프로파일 등에 따른 성능비교를 위하여 서로 다른 9개의 시험편의 성능을 측정하였다. 측정결과 밀도가 낮고 두께가 두꺼운 다공성 강체의 흡음성능이 다소 높은 것으로 나타났으며, 두께의 증가에 따라 중저주파수 대역의 흡음특성이 증가되었다. 배후 공기층이 형성되는 경우 중 저주파수 대역의 흡음성능이 매우 향상되는 것으로 나타났다. 또한 접착제가 사용된 실험편에 배후공기층이 형성되는 경우 전주파수 대역에서 매우 평탄한 수직입사 흡음특성을 갖는 것으로 나타났다. 향후 스테인리스 스틸 다공성 강체가 방음시설물, 흡음.확산용 내장재 등으로 사용될 수 있을 것으로 판단된다.

• Journal of the Korean Magnetics Society
• /
• v.2 no.2
• /
• pp.125-131
• /
• 1992

기판회전 테이블이 부착된 DC, RF-magnetron sputtering 장치로 유리기판 위에 제작한 1000 .angs. 정도의 8.8 .angs. Tb/X .angs. Fe (X=5.4~11.0) 다층박막에 관하여 시료진동형 자 기계와 타원편광 분석장치를 사용하여 자화, 수직자기이방성, kerr 회전각의 Fe층 두께와 열처리 온도 의존성이 연구되었다. Fe층 두께가 7.8 .angs. 기점으로하여 자화용이축의 전이가 나타나기 시작하여 6.4 .angs. 일때 수직자기이방성을 나타낸다. 실험치로부터 계산한 Fe와 Tb층의 경계면 수직이방성 에너지 $K_{s}$ = -0.38 erg/$cm^{2}$이고, Fe층만의 체적수직이방성 에너지 $K_{v}$ = -8.50 * $10^{5}$ erg/$cm^{3}$이다. Polar Kerr 회전각은 Fe층 두께 7.8 .angs. 에서 그대값 2 .THETA. $_{k}$ = 1.22 .deg. 를 갖는다.다.다.다.

• The Journal of Korean Academy of Prosthodontics
• /
• v.58 no.2
• /
• pp.121-129
• /
• 2020

From the point of view of oral rehabilitation, the treatment of extensive tooth wear requires a prosthetic approach. Physiological tooth wear is considered as a normal process and generally does not require treatment, but excessive tooth wear causes problems like inadequate occlusion and esthetics. Changes of occlusal vertical dimension should be made through accurate diagnosis and analysis. Also, the patient's adaptation to the changed occlusal vertical dimension should be assessed over time. This case was a 60-year-old male patient who complained of a decrease in chewing function and esthetics due to severe tooth wear. Full-mouth rehabilitation was performed with a tooth supported fixed prosthesis. An occlusal stabilization splint and provisional restoration were used to evaluate the adaptation to increased occlusal vertical dimension and induce a stable centric relation position. After that, monolithic zirconia prosthesis was delivered. We report this as a satisfactory functional recovery and esthetics.

• The Journal of the Petrological Society of Korea
• /
• v.16 no.1 s.47
• /
• pp.12-26
• /
• 2007

We have studied orientational characteristics of vertical rift and grain planes developing in 108 quarries for Mesozoic granites. Orientations of these planes vary in different localities. In general, orientations of these planes are predominantly NNE in South Korea. From the regional distribution chart, orientations of these planes show three dominant sets in terms of frequency orders: (1) $N2{\sim}10^{\circ}E(1st-order),\;(2)\;N15{\sim}25^{\circ}E(2nd-order),\;(3)\;N45{\sim}70^{\circ}E,\;N10{\sim}30^{\circ}W\;and\;N70{\sim}80^{\circ}W(3rd-order)$. These granite quarries are classified by the relative difference in the easiness of rock splitting between horizontal and vertical quarrying planes into: R-type, G-type, and H-type. The results showed that quarries for Triassic granites belong to R and G-types;those for Jurassic granites belong to R, G and H-types. In addition, quarries for Cretaceous granites belong mainly to R-type. Among these quarry types, the most diverse type was identified in the quarries for Jurassic granites. R-type (77.8%) shows a higher distribution ratio compared with G and H-types (22.2%). In general, anisotropy of physical properties is found in granitic rocks and there exists close correlation between orientations of granitic rock splitting planes and those of the open microcracks. Meanwhile, it has been reported that preferred orientations of open microcracks suggest maxinum principal stress orientations.

• Proceedings of the Optical Society of Korea Conference
• /
• 2002.07a
• /
• pp.184-185
• /
• 2002

고속의 광 통신망을 구축하기 위해서는 대용량의 광 스위치가 요구된다. 이러한 대용량의 광 스위칭 시스템을 구성하는 단위 스위치는 작은 크기, 작은 손실, 높은 소멸비 등과 같은 특징을 가지고 있어야 하며 또한 편광에 따른 성능의 변화가 작아야한다. 최근 융합 수직 방향성 결합기(Fused Vertical Coupler, FVC)의 연구를 통하여 매우 짧은 소자 길이를 가지며 매우 높은 소멸비를 얻을 수 있는 수직 방향성 결합기 스위치가 제안되었다. (중략)

• Proceedings of the Optical Society of Korea Conference
• /
• 2001.02a
• /
• pp.144-145
• /
• 2001

장파장 수직 공진 표면광 레이저는 편리성, 경제성 및 확장성 때문에 많은 주목을 받아 왔다. 이것은 2차원 행렬로 기판에 제작되어 기판 상에서 테스트가 가능하고 기판 표면으로 광 출력이 되는 장점이 있어 모듈 제작비용을 낮출 수 있다. 또한 출력광의 모양을 원형으로 하면 광섬유 연결 효율이 좋아서 광 연결에 필요한 광학부품을 최소화할 수 있다. 특히 1.3-1.55$mu extrm{m}$ 수직 공진 표면광 레이저는 광섬유에서의 분산과 손실이 가장 낮아서 광통신용 광원으로 많은 연구가 진행되고 있다. (중략)

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2009.06a
• /
• pp.129-130
• /
• 2009

컨테이너 터미널에서 하역작업 생산성은 운영전략과 밀접한 관련이 있다. 본 연구는 수직배치형 컨테이너 터미널을 대상으로 여러 운영전략에 따른 하역생산성의 변화를 살펴보았다. 자가하역이 가능한 ALV 이송시스템을 대상으로 시뮬레이션 모형을 개발하여 하역작업 생산성에 대한 민감도 분석을 수행하였다. 실험에 따르면 수직배치인 경우에 본선작업 물량의 장치장 분산 할당이 중요한 것으로 나타났다.

• Geophysics and Geophysical Exploration
• /
• v.23 no.4
• /
• pp.223-229
• /
• 2020

Small-loop EM techniques have been used in many geophysical investigations, including shallow engineering and environmental surveys. Even though geometric and frequency soundings have been widely used, there is a debate regarding the effectiveness of frequency sounding, especially when the coil spacing is small. In this study, we analyzed the effectiveness of geometric as well as frequency soundings via the one-dimensional modeling of small-loop EM surveys. The numerical results reveal that geometric sounding can effectively provide underground information. Conversely, the frequency soundings are only effective when the loop spacing is relatively large, that is, when the induction number is large. On the contrary, the frequency soundings fail to provide any information concerning the subsurface layers if the loop spacing is not large.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.24 no.6
• /
• pp.197-205
• /
• 2020

In 2014, The Housing Act amended to allows vertical extension and increases the units of housing (or total floor area) to site. Currently, the feasibility of performing vertical extension is evaluated based on safety diagnosis provisions and manuals with 1st investigation stage on slope, uneven settlement, load-bearing capacity, and durability. However, a need for more reasonable evaluation criteria for the investigation is still required because there had not been any other case study on the diagnosis for the vertical extension, and the engineering basis on evaluation criteria were not suggested. Accordingly, this study is intended to suggest feasible evaluation criteria on the carbonation, chloride ion contents, corrosion of reinforcements, crack and surface deterioration of concrete for durability assessment by codes and standards of domestic and foreign countries. The results of this study are expected to be beneficial for establishing more reasonable durability evaluation criteria, and in turn, more reliable assessment protocol for vertical extension.