• Analytical Science and Technology
• /
• v.12 no.6
• /
• pp.515-520
• /
• 1999

The spectrophotometric determination of Al(III) with thorin have been investigated. The optimum condition of pH, concentration of ligand and surfactant, and stability were evaluated. The thorin ligand offers selective separation of Al(III) from sample solution containing Fe(III), Ni(II), Cu(II), Pb(II) and Cu(II). Various surfactants were tested and Triton X-100 showed the best stability and the maximum absorbance in an aqueous solution of Al(III)-Thorin-Triton X-100 complex appears about 526 nm. The method was applied for the determination of Al(III) in mixed sample solution. Separation and preconcentration was performed with a short column filled with resorcinol-formaldehyde resin. Control of the pH during the column operation is essential because the adsorption capacities are very sensitive to change in pH. Their separation was carried out in 0.2 M acetic acid-sodium acetate buffer solution (pH 4.5) and 1.0 M $HNO_3$media.

• Journal of the Korean Wood Science and Technology
• /
• v.34 no.4
• /
• pp.31-36
• /
• 2006

This study was conducted to improve the bond strength of plywood bonded with F/U molar ratio urea-formaldehyde (UF) resins modified with the selected FGMDI prepolymer contents for various purposes. The amount of FGMDI was mixed with liquid UF resin at 0 wt% (as control), 2 wt%, 5 wt%, 10 wt%, 25 wt%, and 50 wt% based on the resin solids. As results, in bonding strength, plywood with F/U molar ratio of 1.4 showed the highest value in Type 2 test and all molar ratio UF resins modified with over 25 wt% of the FGMDI showed more than $11kgf/cm^2$, which was satisfied the minimum requirement of KS standard, $7.5kgf/cm^2$, after Type1.5 testing. As F/U molar ratio was increased and the FGMDI addition in the UF resin was increased, average reduction rate of Type 1.5 bonding strength compared with Type 2 was significantly decreased.

• Composites Research
• /
• v.17 no.6
• /
• pp.37-43
• /
• 2004

To determine the effect of chain length and chemical structure of linear amine curing agents on thermal and mechanical properties, a standard bifunctional linear DGEBF epoxy resin was cured with EDA and HMDA having amine group at the both ends of main chain in a stoichiometrically equivalent ratio in condition of preliminary and post cure. From this work, the effect of linear amine curing agents on the thermal and mechanical properties is significantly influenced by numbers of carbon atoms of main chain. In contrast, the results show that the DCEBF/EDA system having two carbons had higher values in the thermal stability, density, shrinkage (%), grass transition temperature, tensile modulus and strength, flexural modulus and strength than the DGEBF/HMDA system having six carbons, whereas the DGEBF/EDA cure system had relatively low values in maximum ekothermic temperature, maximum conversion of epoxide, thermal expansion coefficient than the DGEBF/HDMA cure system. These findings indicate that the packing capability (rigid property) in the EDA structure affects the thermal and mechanical properties predominantly. It shows that flexural fracture properties have a close relation to flexural modulus and strength.

• Resources Recycling
• /
• v.8 no.3
• /
• pp.3-8
• /
• 1999

An air-washer was developed in order to remove the soil on the films collected from agricultural use, The washed films were subjected to TGA analysis to measure the residual soil content and DSC analysis to evaluate composition as well as compositional ratro, Mechanical properties of washed films were measured via tensile test ,md the properties of washed films were compared with those of neat resin blend. Major component of air washed films was polyethylene, and compositional ratio was 10:6:3:1 (HDPE:LLDPE:LDPE:EVA). 30 min air-washed films showed 2.1 % of residual soil content, while the water washed films had 1.5%. Tensile properties of washed (air and water) films were almost same as those of neat resin mixture.

• Applied Chemistry for Engineering
• /
• v.8 no.2
• /
• pp.197-203
• /
• 1997

The effect of additives on the mechanical properties of polyurethane foam were investigated. The resin used in this study was prepared by adding catalyst, surfactant and cross-linker to both KONIX FA-703 polyether polyol(80%) and KONIX FA-733 polyether polyol(20%). The polyurethane was foamed by adding equivalent amount of isocyanate(TDI-80, prepolymer M-200, pure MDI) to the resin and was used in property measurements after 72 hours hardening. The physical properties of polyurethane foam were investigated in terms of density, tensile strength, tear strength, elongation, sound absorption coefficient and gel profile measurements. The effects of surfactant on the cell size was investigated by scanning electron microscopy(SEM). The sound absorption coefficient was directly related to the cell size. The physical properties were improved with increasing amount of surfactant(L-5309) until 1.0 part per hundred polyol(1.0pphp).

• Polymer(Korea)
• /
• v.28 no.5
• /
• pp.374-381
• /
• 2004

Gas permeability of low density polyethylene (LDPE) film containing zeolite powder for $CO_2,\;O_2$ and $N_2$ were investigated. Zeolite powders modified by cations or surfactant were compounded with LDPE to produce $20 wt\%$ masterbatch. After blending the masterbatch with LDPE, zeolite filled films were prepared by the blown film process. Finally, the composite films containing zeolite loadings of 0, 3,5, and $10 wt\%$ were produced. A gas permeability apparatus based on the variable volume principle was designed to analyze the characteristics of films. Experiments showed a general trend that gas permeabilities first decreased and then increased as the zeolite content was increased. Surfactant modified zeolite showed a better interfacial adhesion with the matrix, but the film did not show a discernible difference in gas permeability compared with the other modified films. The difference of temperature dependences in the gas permeabilities of composite films was slightly smaller than that of LDPE film.

• Elastomers and Composites
• /
• v.35 no.3
• /
• pp.205-214
• /
• 2000

The polyurethane resin was prepared by the reaction of tolylenediisocyanate(TDI) and polypropyleneglycol(PPG). Physical properties of the resin were investigated experimentally. Charging catalyst before TDI-dropping induced the rapid increase of viscosity. On the other hand, charging catalyst after TDI-dropping resulted in mild stability without immoderate generation of heat on reaction. The use of phosphoric acid as catalyst led to low viscosity by restraining side-reaction such as forming of branch-chain, buret reaction and allopanate reaction, but it showed low cross-link density and slow drying. The curing speed was more influenced by structures of molecules rather than NCO/OH ratio. Including PPG 400 over 30 wt % showed excellent adhesive strength due to increase of crosslink density.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.13 no.4 s.56
• /
• pp.126-136
• /
• 2009

The sprayed FRP strengthening technique is combining the Glass fiber and Polyester resin in open air and spraying randomly at concrete's surface with high-speed compressed air. Then it strengthens the structures with a new technique evaluated the structural performance. We applied it to concrete beam and tested for flexural strength, depended on Korea Standard(KS F 2408). Then based on the result of flexural strength, the properties were proposed that applying to structures. Based on the experiment, we have evaluated structural performance by the experiment. 1/5 scale prestressed concrete I-beam were made by Korean Highway's typical drawing in 1993. With these test results, 49.8% increased in flexural strength, improvement of the behavior of serviceability state, and strengthening was surely effective for controlling deflection and crack of structure. Consequently, it can be summarized that Sprayed FRP technique has prospect to improve the performance of structure.

• Elastomers and Composites
• /
• v.46 no.4
• /
• pp.335-342
• /
• 2011

The virgin and recycled polyethylene composites with various ratio of fly ash were manufactured by using a fully intermeshing co-rotating twin screw extruder for the reuse of fly ash from power plant and post-consumed polyethylene. Fly ash were blended with virgin HDPE and recycled polyethylene at the weight fraction of 0 to 40 wt.%. Mechanical properties such as yield strength, abrasion resistance, and slow crack resistance were measured with ISO and ASTM standards. The experimental results for the various composites showed that the elongation at break and the yield stress of the composites decreased with increasing fly ash contents. Generally, the abrasion resistance of PEs decreased with increasing sandpaper grits but the abrasion resistance of the composites increased with fly ash content at finer abrasive surface. The slow crack growth resistance of virgin HDPE, recycled JRPE and the JRPE composite showed higher slow crack growth resistance up to 50% of load at notch depth of 20% and 30%, but KRPE and the KRPE composite showed much lower resistance than virgin HDPE, JRPE and the JRPE composite. Time to break, measured with NCLS test method, of all PEs and the composites satisfies the regulation of Korean Industrial Specification for sewer pipe and support application.

• Applied Chemistry for Engineering
• /
• v.20 no.2
• /
• pp.234-240
• /
• 2009

$Mg(OH)_2$ particles were prepared by precipitation and a hydrothermal treatment to examine the effect of $MgCl_2$ concentration, alkali type and concentration, temperature, hydrothermal treatment on the formation of $Mg(OH)_2$ particles using full factorial design, as one of DOE (Design of experiment) methods. The primary particle size is similar to the secondary particle size for the samples after the hydrothermal treatment, where the average particle size of $Mg(OH)_2$ increased with increasing the concentration of $MgCl_2$ and hydrothermal temperature and decreasing alkali/Mg molar ratio. On the other hand, for the samples prepared from precipitation, the secondary particle size is larger than the primary particles due to aggregation. The difference in alkaline source is that the particles prepared from $NH_4OH$ exhibit the larger size with better dispersion than those from NaOH. Low density polyethylene and ethylene-co-vinyl acetate (LDPE-EVA) resin composed of the smaller secondary particle size of $Mg(OH)_2$ shows a higher limited oxygen index (LOI) at 50 and 55% loading, but the smaller primary particle size may result in a better grade in UL-94 tests. At the high loading of 60%, all samples with any preparation methods exhibit V-0 grade but the LOI value depends on not only primary particle size but also dispersion state.