• 한국수소및신에너지학회논문집
• /
• 제24권2호
• /
• pp.113-120
• /
• 2013

A steam reformer is a chemical reactor to produce high purity hydrogen from fossil fuel. In the steam reformer, since endothermic steam reforming is heated by exothermic combustion of fossil fuel, the heat transfer between two reaction zones dominates conversion of fossil fuel to hydrogen. Steam Reforming is complex chemical reaction, mass and heat transfer due to the exothermic methane/air combustion reaction and the endothermic steam reforming reaction. Typically, a steam reformer employs burner to supply appropriate heat for endothermic steam reforming reaction which reduces system efficiency. In this study, the heat of steam reforming reaction is provided by anode-off gas combustion of stationary fuel cell. This paper presents a optimization of heat transfer effect and average temperature of cross-section using two-dimensional models of a coaxial cylindrical reactor, and analysis three-dimensional models of a coaxial cylindrical steam reformer with chemical reaction. Numerical analysis needs to dominant chemical reaction that are assumed as a Steam Reforming (SR) reaction, a Water-Gas Shift (WGS) reaction, and a Direct Steam Reforming(DSR) reaction. The major parameters of analysis are temperature, fuel conversion and heat flux in the coaxial reactor.

• 한국수소및신에너지학회논문집
• /
• 제26권5호
• /
• pp.445-452
• /
• 2015

A tubular packed bed reactor for the steam-$CO_2$ combined reforming of natural gas to produce the synthesis gas of a target $H_2/CO$ ratio 2.0 was simulated. The effects of the reactor dimension, the feed gas composition, and the gas feeding temperature upon the possibility of coke formation across the catalyst bed were investigated. For this purpose, 2-dimensional heterogeneous reactor model was used to determine the local gas concentrations and temperatures over the catalyst bed. The thermodynamic potential distribution of coke formation was determined by comparing the extent of reaction with the equilibrium constant given by the reaction, $CH_4+2CO{\Leftrightarrow}3C+2H_2O$. The simulation showed that catalysts packed in the central region nearer the entrance of the reactor were more prone to coking because of the regional characteristics of lower temperature, lower concentration of $H_2O$, and higher concentration of CO. With the higher feeding temperature, the feed gas composition of the increased $H_2O$ and correspondingly decreased $CO_2$, or the decrease in the reactor diameter, the volume fraction of the catalyst bed subsequent to coking could be diminished. Throughout the simulation, reactor dimension and reaction condition for coking-free operation were suggested.

• 공업화학
• /
• 제20권4호
• /
• pp.423-429
• /
• 2009

본 연구의 목적은 바이오가스를 이용하여 고농도 수소 생산과 CO 제거가 가능한 글라이딩아크 플라즈마 개질 시스템의 개발이다. 이를 위하여 수성가스 전이반응기는 수증기 주입량 변화,촉매층 온도 변화에 대하여, 선택적 산화반응기는 촉매층 온도변화, 공기주입량에 대하여 실험을 진행하였다. 기준조건은 S/C 비 3, 촉매층 온도 $700^{\circ}C$, 전체가스량 16 L/min, 입력전력 2.4 kW, 바이오가스 구성비($CH_4$ : $CO_2$ ) 6 : 4이다. 이때의 실험결과는 HTS의 최적조건은 S/C비 3, 반응온도 $500^{\circ}C$, LTS의 최적조건은 S/C 비 2.9, 반응온도 $300^{\circ}C$이다. 또한 PROX I단의 최적조건은 각각 공기유입량 300 mL/min, $190^{\circ}C$, PROX II단의 최적조건은 공기유입량 200 mL/min, $190^{\circ}C$을 나타내었다. 반응기를 모두 지난 후의 합성가스는 $H_2$ 수율 55%, $CH_4$ 전환율 97%, $CO_2$ 전환율 97%, CO 선택도는 0%로 바이오가스를 개질하여 생성된 합성가스는 높은 수율을 나타내며, CO 선택도는 0%를 나타내었다.

• 대한기계학회논문집B
• /
• 제37권8호
• /
• pp.753-758
• /
• 2013

본 연구는 MCFC용 벽면가열 방식 프리컨버터의 낮은 열전도율 때문에 발생하는 벽면 고온 발생 문제를 해결하기 위한 두 가지 방안을 수치해석을 통해 연구하였다. 프리컨버터 내부에 열전도율이 높은 다공성판을 설치한 경우 벽면에서 중심부위로 열전달이 향상되어 수소 생성이 벽면부위에 국한되지 않고 촉매내부에 좀 더 균일하게 발생되는 것을 확인하였다. 그리고 촉매 내부에 일정한 두께의 빈 공간을 중심, 1/2 그리고 4/5 위치에 두고 해석하여 결과를 비교하였고, 1/2위치의 빈 공간이 다른 경우에 비해 연료전환이 보다 이상적인 경우에 근접하지만 열전도율이 높은 다공성판의 설치가 보다 효과적임을 확인하였다.

• 한국수소및신에너지학회논문집
• /
• 제13권2호
• /
• pp.119-126
• /
• 2002

The methanol partial oxidation using commercial $CuO/ZnO/Al_2O_3$ catalysts in a plug flow reactor was studied in the temperature range of $200{\sim}250^{\circ}C$ at atmospheric pressure, It was achieved the high activities by Cu-based catalysts and the selectivity of $CO_2$/$H_2$ was 100% when $O_2$ was fully convened. The reactivity changes and their hysteresis with increasing/decreasing temperatures were observed due to the chemical state differences between the oxidation and the reduction on the Cu surface, It was suggested as the two-step reaction: the complete oxidation and the following steam reforming for methanol, which was indicated by the distributions of final products vs. the residence time. In addition, the complete oxidation step was shown to be extremely fast and the total reaction rate can be controlled by the steam reforming reaction.

• 에너지공학
• /
• 제20권3호
• /
• pp.252-258
• /
• 2011

Nickel fiber mat was investigated as a potential structured catalyst for steam reforming of biogas in the temperature range of $600-700^{\circ}C$. The activity of as-received catalyst was very low owing to the smooth surface of fibers. Pretreatment of the catalyst by oxidation followed by reduction under methane partial oxidation condition significantly improved the catalytic activity, although degradation of the activity was found during the reaction due to oxidation and sintering. This deactivation was retarded by supplying additional hydrogen in the inlet gases or by coating $CeO_2$ over the catalyst surfaces.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2011년 춘계학술대회논문집
• /
• pp.112-116
• /
• 2011

In this paper, a preconverter of MCFC for an emergence electric power supplier is numerically simulated to increase the hydrogen production from natural gas (methane). Commercial code is used to simulated the porous catalyst with user subroutine to model three dominant chemical reactions which are Stream Reforming(SR), Water-Gas Shift(WGS), and Direct Stram Reforming(DSR). To get 10% fuel conversion rate in preconverter. the required external heat flux is supplied from outer wall of preconverter. The calculated results show that very nonuniform temperature distribution and chemical reaction happen near the wall of preconverter. These phenomena can be explained by the low heat conductivity of porous catalyst and the endothermic reforming reaction.

• 한국수소및신에너지학회논문집
• /
• 제34권6호
• /
• pp.581-586
• /
• 2023

As the development of alternative energy is required due to the depletion of fossil fuels, interest in the use of hydrogen energy is increasing. Hydrogen is a promising clean energy source with high energy density and can lead to the application of environmentally friendly technologies. However, due to difficulties in production, storage, and transportation that prevent the application of hydrogen-based eco-friendly technology, research on reforming reactions using dimethyl ether (DME) is being conducted. Unlike other hydrocarbons, DME is attracting attention as a hydrogen carrier because it has excellent storage stability and transportability, and there is no C-C bond in the molecule. The reaction between DME and steam is one of the reforming processes with the highest hydrogen yield in theory at a temperature lower than that of other hydrocarbons. In this study, a hydrogen reforming device using DME was developed and a catalyst prepared by supporting Cu in alumina was put into a reactor to find optimal hydrogen production conditions for supplying hydrogen to fuel cells while changing reaction temperature (300-500℃), pressure (5-10 bar), and steam/carbon ratio (3:1 to 5:1).

• 한국수소및신에너지학회논문집
• /
• 제29권6호
• /
• pp.559-569
• /
• 2018

Catalytic supports made of carbon have many advantages, such as high coking resistance, tailorable pore and surface structures, and ease of recycling of waste catalysts. Moreover, they do not require pre-reduction. In this study, ash-free coal (AFC) was obtained by the thermal extraction of carbonaceous components from raw coal and its performance as a carbon catalytic support was compared with that of well-known activated carbon (AC). Nickel was dispersed on the carbon supports and the resulting catalysts were applied to the steam reforming of toluene (SRT), a model compound of biomass tar. Interestingly, nickel catalysts dispersed on AFC, which has a very small surface area (${\sim}0.13m^2/g$), showed higher activity than those dispersed on AC, which has a large surface area ($1,173A/cm^2$). X-ray diffraction (XRD) analysis showed that the particle size of nickel deposited on AFC was smaller than that deposited on AC, with the average values on AFC ${\approx}11nm$ and on AC ${\approx}23nm$. This proved that heteroatomic functional groups in AFC, such as carboxyls, can provide ion-exchange or adsorption sites for the nano-scale dispersion of nickel. In addition, the pore structure, surface morphology, chemical composition, and chemical state of the prepared catalysts were analyzed using Brunauer-Emmett-Taylor (BET) analysis, transmission electron microscopy (TEM), scanning electron microscopy (SEM), x-ray diffraction (XRD), Fourier-transform infrared (FT-IR) spectroscopy, and temperature-programmed reduction (TPR).

• 대한화학회지
• /
• 제15권2호
• /
• pp.55-63
• /
• 1971

In this study, several nickel catalysts for the steam-hydrocarbon reforming process were prepared from various nickel salt, magnesium oxide, alumina and kaolinite. The activity and strength of the catalysts were investigated. 1. The proper composition of the calcined catalysts are: NiO (5-15%)-MgO(10-20%)-$Al_2O_3$(10-40%)-Kaolinite(50-80%). 2. The admixed or cosedimented ingredients of the catalysts was pelletized and calcinated at 1000 or $1150^{\circ}C$. Calcination at $1150^{\circ}C$ for an hour was optimum. 3. The water to oil ratio (W/O) for reforming of hexane should be above 7 mole/mole. As the W/O increases, more carbon dioxide and hydrogen, but less carbon monoxide was produced. Also carbon deposition become lessen at higher W/O. 4. Maximum conversion had attained at about $850^{\circ}C$. As the reaction temperature increases, more carbon monoxide and hydrogen, but less carbon dioxide and lower hydrocarbon was produced. 5. The percent conversion at $850^{\circ}C$ was about 80%, using a catalyst which the nickel oxide content are 5%.