• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2005.11a
• /
• pp.285-292
• /
• 2005

• Journal of the Korean Wood Science and Technology
• /
• v.4 no.1
• /
• pp.21-27
• /
• 1976

This study was carried out in order to obtain the effect of active alkali concentration. Sulfidity 25%, maximum temperature 170$^{\circ}C$, cooking time 3hrs., liquor to wood ratio 5 : 1 in the kraft cooking conditions were maintained. Active alkali concentration were varied at intervals of 3% between 12% and 24%. The rates of de lignification increased with an increase in active alkali concentration and beatability, brightness, and strength of pulp also improved. The total pulp yield trand to decrease with an increase of active alkali concentration. The maximum screened pulp yield were obtained between 18% and 21% A.A.. Therefore, the optimum active alkali concentration was 18~21%.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.6 no.2
• /
• pp.315-322
• /
• 2002

A thin film oxide semiconductor micro gas sensor array which shows only 60㎽ of power consumption at an operating temperature of 30$0^{\circ}C$ has been fabricated using microfabrication and rnicrornachining techniques. Excellent thermal insulation of the membrane is achieved by the use of a double la! or structure of 0.1${\mu}{\textrm}{m}$ thick Si$_3$N$_4$ and 1${\mu}{\textrm}{m}$ thick phosphosilicate glass(PSG) prepared by low pressure chemical vapor deposition(LPCVD) and atmospheric－pressure chemical-vapor deposition(APCVD), respectively. The sensor way consists of such thin film oxide semiconductor sensing materials as 1wt.％ Pd-doped SnO$_2$, 6wt.% AI$_2$O$_3$-doped ZnO, WO$_3$ and ZnO. The thin film oxide semiconductor micro gas sensor array exhibited resistance changes usable for subsequent data processing upon exposure to various gases and the sensitivity strongly depended on the sensing layer materials. Heater Part of the sensor structure has been modified in order to improve the process yield of the sensor, and as a result of modified heater structure improved process yield has been achieved.

• Microbiology and Biotechnology Letters
• /
• v.42 no.1
• /
• pp.25-31
• /
• 2014

Fractional precipitation is a simple method for purifying (+)-dihydromyricetin extracted from biomass. However, the fractional precipitation process has been inherently problematic due to the lengthy precipitation time that is required. The fractional precipitation time was shortened and (+)-dihydromyricetin yield was improved by increasing the surface area per working volume (S/V) of the reacting solution through the addition of a cation exchange resin (Amberlite 200, Amberlite IR 120Na, Amberlite IR 120H, or Amberlite IRC 50). Most of the (+)-dihydromyricetin (>90%) could be obtained after about 16 h of fractional precipitation using Amberlite 200. Since high-purity (+)-dihydromyricetin can be obtained at a high yield and the precipitation time can be reduced by increasing the surface area available for precipitation, this improved method is expected to minimize solvent usage and the size and complexity of the high performance liquid chromatography operation required for (+)-dihydromyricetin purification.

• Journal of Biosystems Engineering
• /
• v.5 no.2
• /
• pp.15-25
• /
• 1980

본 연구는 현재 국내 농촌에서 문제시되고 있는 벼의 건조와 저장방법을 개선하기위한 한 가지 방법으로써 Grain bin의 이용에 따른 기술적인 적용가능성을 구명하는데 있었으며 건조열원으로서는 상온공기와 Solar collector 에 의한 보충가열공기를 사용하였다. 건조시험에서는 벼의 건조속도, 층별함수율의 변화, 동력소모량, 도청수율 등을 측정 비교하였으며 건조가 완료된 후에는 저장시험도 아울러 실시하였다. 본 시험을 통하여 얻은 결과는 다음과 같다. 1. 본시험에 사용된 Solar Collector 는 집열면적이 $27.7m^2M$의 Flat-plate 형식이며 내부에 태양열의 저장모체로서 약 $7m^2M$의 검은 돌을 사용하였다. Collector 의 효율은 35%이었으며 Collector를 통과하여 Bin으로 들어가는 공기의 온도는 외기온에 비하여 주간에는 약 $4^\circ C$, 야간에는 약 $8^\circ C$, 정도 상승된 것으로 나타났다. 2. 상온공기와 Collector를 이용한 건조험결과 안전저장함수율에 도달하는 데 약 7일과 약 5일이 소요되었다. 3. 태양열 건조는 상온통풍건조에 비하여 곡물층간의 함수율차이가 약간 크게 나타났으나 건조속도가 빠를뿐만 아니라 동력소모량도 적은 것으로 분석되었다. 4. 건조시험이 완료된 직후 이차에 걸쳐 Bin 내에서 저장시험을 실시한 결과 저장기간중 벼의 안전보전이 가능했으며 평균함수율이 12.0~14.5%범위에서 유지되었다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.6
• /
• pp.2697-2701
• /
• 2012

The yield of OTP devices using anti-fuse MOS capacitor have been affected by the input resistance, the size of the pass transistor and the read transistor, and the readout voltage of programed cell. To investigate the element which gives an effect to yield, we analyze the full map data of the resistance characterization of OTP device and those data in a various experimental condition. As a result, we got the optimum conditions which is necessary to the yield improvement. The optimum conditions are as follows: Input resistance is 50 ohms, the channel length of pass transistor is 10um, read voltage is 2.8 volt, respectively.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.32 no.12A
• /
• pp.1320-1328
• /
• 2007

In recent year, the popularity of WLAN has generated much interests on improvement and performance analysis of the IEEE 802.11 protocol. In this paper, we analyze two medium access methods of the IEEE 802.11 MAC protocol by investigating the MAC layer packet service times when arrival packet sizes have a general probability distribution. We use the M/G/1/K queueing model to analyze the throughput and the delay performance of IEEE 802.11 MAC protocol in a wireless LAN. We compare the performances of Basic access method and RTS/CTS access method. We take some numerical examples for the system throughput and the queue dynamics including the mean packet delay and packet blocking probability.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.33 no.2A
• /
• pp.130-138
• /
• 2008

In this paper, we propose a user selection method to maximize the sum-rate of downlink over opportunistic beamforming. The throughput of an opportunistic beamforming with non-uniformly distributed or a small number of users can decrease. In order to improve the throughput, we propose a scheduling method that does not use SINR or SNR but uses the effective channel gain of each user obtained from the SINR or SNR feedback. The proposed method makes it possible to select users flexibly according to the distribution of users. In numerical results, we show that the proposed methods improve the average sum-rate about 60% when users are distributed non uniformly.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.40 no.10
• /
• pp.35-42
• /
• 2003

In this paper, we classified the wavelength reservation mechanisms of optical burst switching (OBS), and investigated the path length priority effect of the offset time/delayed reservation (OT/DR)-based scheme like the just-enough-time (JET) protocol. And, we showed that the fiber delay line (FDL)-based scheme can avoid the path length priority effect in multiple hop network environments. Also, we proposed a novel FDL/DR with hop-by-hop priority increasing (HPI) scheme which can improve the end-to-end throughput by increasing the priority of bursts hop-by-hop using the input FDLs at each node. The simulation results showed that the proposed FDL/DR with HPI scheme could avoid the path length priority effect and enhance the end-to-end throughput in multiple hop network environments.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.227-227
• /
• 2010

기존 실리콘 박막 태양 전지는 적외선에 대한 감응도와 흡수도가 낮아서 광흡수율을 증가시킬 경우 효율의 효과적인 개선이 기대되어진다. 이를 개선하기 위해서 밴드갭이 Si에 비해 상대적으로 낮은 Ge을 도입함으로써 Si와 Ge 화합물을 형성할 경우 결정상태와 수소 함유량에 따라 밴드갭 조절이 가능하다. 또한 Ge는 Si에 비해 빛에 대한 감응도가 우수하여 광흡수율을 증가시킬수 있다. 단 SiGe 박막의 Ge 량이 일정량이상 많아질 경우 박막 내 결함 등의 생성으로 광변환 효율이 오히려 감소하므로 Ge 량의 적정화가 필요하다. 본 실험에 사용된 SiGe:H Layer는 $SiH_4$ 가스와 $GeH_4$ 가스를 혼합하여 증착하였고 증착두께는 150nm로 고정하였으며 증착장비는 PECVD를 이용하였다. 파워는 플라즈마의 방전특성을 알아본 후 최소파워를 이용하여 증착하였다. 이는 증착 시 플라즈마에 의한 박막 손상을 최소화하기 위함이다. Ellipsometry를 이용하여 박막의 두께와 optical bandgap을 측정하였다. 박막의 특성을 평가하기 위해서 STA 장비를 이용하여 dark conductivity, photo conductivity, activation energy 등을 측정하였고, MDC를 이용해 C-V 곡선을 측정하였고, 이를 terman method를 이용하여 $D_{it}$를 계산하였다.