• 에너지공학
• /
• 제28권4호
• /
• pp.1-7
• /
• 2019

최근 수소충전소 수요 증가에 따라, 산업통상자원부는 LPG, CNG, 주유소 등 기존의 자동차용 연료공급시설 내에 융합, 복합의 형태로 수소충전소 설치가 가능하도록 특례고시를 제정·공포하였다. 수소 융복합충전소는 특례기준 제정 이전까지 국내에서 운영된 사례가 없어, 4계절, 일교차와 같은 환경특성을 감안한 실증이 필요하다. 본 연구에서는, 국내 최초로 실증을 위해 설치된 울산 LPG-수소복합충전소의 충전데이터를 수집하여 분석하였다. 충전데이터는 압축기, 저장용기, 디스펜서에서 발생한 시간별 온도, 압력 데이터이며, 계절별 특성을 비교하기 위해 2018년 7월 중 울산 지역의 최고기온 일과 2018년 1월 중 최저기온 일을 포함하여 4계절 충전데이터를 수집하여 비교하였다. 비교결과, 외기온도의 변화가 수소차 차량용기의 초기온도에 영향을 미치는 것으로 나타났으며, 이는 최종적으로 차량의 충전시간과 충전속도에도 영향을 미치는 것으로 나타났다. 국내 수소충전소 기준(KGS FP217)과 미국의 충전프로토콜(SAE J2601)에서 제시한 한계온도를 초과한 경우는 없어 차량용기에 대한 영향은 없는 것으로 나타났다.

• 한국수소및신에너지학회논문집
• /
• 제13권4호
• /
• pp.297-303
• /
• 2002

The purpose of study is obtaining low-emission and high-efficiency in LPi engine with hydrogen enrichment. The test engine was named variable compression ratio single cylinder engine (VACRE). The fuel supply system provides LPG/hydrogen mixtures based on same heating value. A varied sensors such as crank shaft position sensor (CPS) and hall sensor supplies spark timing data to ignition controller. Displacement of VACRE is $1858.2cm^3$. VACRE was runned 1400rpm with compression ratio 8. Spark timing was set MBT without knocking. Relative air-fuel ratio($\lambda$) of this work was varied between 0,8 and 1.5.

• Korean Chemical Engineering Research
• /
• 제50권2호
• /
• pp.353-357
• /
• 2012

액화석유가스(liquefied petroleum gas, LPG)에 디메틸에테르(dimethyl ether, DME)가 첨가된 DME-LPG 혼합연료의 탄화수소 화합물을 가스크로마토그래피(GC)를 이용하여 정성 정량분석하는 새로운 분석방법을 연구하였다. DME-LPG 혼합연료는 함산소화합물(oxygen-containing compound)인 극성의 DME와 비극성물질인 LPG로 구성되어 있기때문에 하나의 GC 컬럼에서 모든 성분을 완전히 분리하기가 어렵다. 따라서 서로 다른 성질의 화합물이나 아주 복잡한 화합물 중 목표물질의 분석에 응용되고 있는 Deans switching 시스템을 도입하였다. 상기 시스템은 두 개의 GC 컬럼 사이에 유체의 압력 제어를 통하여 용출되는 물질의 흐름 방향을 변경시켜주는 기술로서, 이 방법을 이용하여 DME와 LPG를 서로 다른 컬럼에서 분리하여 한번의 시료 주입으로 DME-LPG 혼합연료의 모든 탄화수소 화합물을 정성 정량분석할 수 있었다. 또한 DME 합성과정에서 부산물로 생성될 수 있는 메탄올, 포름산메틸, 에틸메틸에테르 같은 미량성분까지 분석이 가능하였다.

• 한국수소및신에너지학회논문집
• /
• 제20권2호
• /
• pp.161-167
• /
• 2009

The regulation of the $CO_2$ emit from vehicles have become much more stringent in recent years. This stringent regulation is more request vehicle manufacturers to develop the alternative fuel vehicles for reducing exhaust emissions. LPG fuel is more clean energy compares with gasoline and diesel fuel. Especially, $CO_2$ emission of LPG Vehicle is less than gasoline vehicle and almost equal to diesel vehicle. For this reason, recently korean government is extending LPG fuel for hybrid car and light duty vehicle. In domestic, Propane is mixing $15{\sim}30%$ to butane for improvement of cold start at winter season. Therefore, In this paper was investigated that the characteristics of emissions according to propane mixing rate with 0, 10, 20, 30% were compared and analyzed by the vehicle test using LPG vehicle according to the FTP75 mode. It was also investigated the characteristics of nano-particle emit with propane mixing rate.

• 한국수소및신에너지학회논문집
• /
• 제29권5호
• /
• pp.497-502
• /
• 2018

In Korea, passenger car and van using LPG fuel including taxi constantly increased due to the high cost of fuel. Recently, the emission standard has continuously tightened in the world. In this investigation was conducted the greenhouse gas emission characteristics of LPG vehicles according to the displacement and weight. Exhaust emission characteristics of 13 test LPG vehicles from about 1.0 L to 3.0 L displacements were measured and analyzed by using chassis dynamometer and emission analyzer. It is revealed that the greenhouse gas emission was showed the increasing tendency as the displacement and curb weight increased. Also, greenhouse gas emission of SC03 driving cycle has highest value and that of HWFET driving cycle shows the lowest value.

• 한국수소및신에너지학회논문집
• /
• 제12권3호
• /
• pp.169-176
• /
• 2001

The purpose of study is to obtain low-emission and high-efficiency in LPG engine with hydrogen enrichment. The test engine was named heavy-duty variable compression ratio single cylinder engine (VCSCE). The fuel supply system provides LPG/hydrogen mixtures based on same heating value. Various sensors such as crank shaft position sensor (CPS) and hall sensor supply spark timing data to ignition controller. Displacement of VCSCE is $1858.2cm^3$. VCSCE was runned 1400rpm with compression ratio 8. Spark timing was set MBT without knocking. Relative air-fuel ratio(${\lambda}$) of this work was varied between 0.76 and 1.5. As a result, i) Maximum thermal efficiency occurred at ${\lambda}$ value 1.0. It was shown that thermal efficiency was increased approximately 5% with hydrogen enrichment at same ${\lambda}$ value. ii) Engine-out carbon monoxide (CO) emissions were decreased at a great rate under LPG/hydrogen mixture fuelling. iii) Total hydrocarbon (THC) emission was much exhausted in rich zone, same as CO. But THC was exhausted a little bit more in lean zone. iv) Finally, engine-out oxides of nitrogen (NOx) was increased with ${\lambda}$ value 1.0 zone at a greater rate with hydrogen enrichment due to high adiabatic flame temperature.

• 한국수소및신에너지학회논문집
• /
• 제26권1호
• /
• pp.1-7
• /
• 2015

In this study, characteristics of reforming process of automotive liquefied petroleum gas (LPG) fuel using plasma reactor are investigated. Because plasma reformer technology has advantages of a fast start-up and wide fuel/oxidizer ratio of operation, and reactor size is smaller and more simple compared to typical combustor and catalytic reactor, plasma reforming is suitable to the on-board vehicle reformer. To evaluate the characteristics of the reforming process, parametric effect of $O_2/C$ ratios, reactant flow rate and metal form on the process were investigated. In the test of varying $O_2/C$ ratio from partial oxidation to stoichiometry combustion, conversion of LPG was increased but selectivity of $H_2$ decreased. The optimum condition of $O_2/C$ ratio for the highest $H_2$ yield was determined to be around 1.0 for 20~50 lpm, and 1.35 for 100 lpm. Specific energy density (SED) was major factor in reforming process and higher SED leads to higher $H_2$ yield. And metal form in the reformer increased $H_2$ yield of about 34 % as compared to the case of no metal form. The result can be a guide to map optimal condition of reforming process.

• 한국수소및신에너지학회논문집
• /
• 제27권1호
• /
• pp.106-113
• /
• 2016

Lean burn engine, classified into port injection and direct injection, is recognized as a promising way to meet better fuel economy. Especially, LPG direct injection engine is becoming increasingly popular due to their potential for improved fuel economy and emissions. Also, LPDi engine has the advantages of higher power output, higher thermal efficiency, higher EGR tolerance due to the operation characteristics of increased volumetric efficiency, compression ratio and ultra-lean combustion scheme. However, LPDi engine has many difficulties to be solved, such as complexity of injection control mode (fuel injection timing, injection rate), fuel injection pressure, spark timing, unburned hydrocarbon and restricted power. This study is investigated to the influence of spark timing, fuel injection position and fuel injection rate on the combustion stability of LPDi engine. Piston shape is constituted the bowl type piston. The characteristics of combustion is analyzed with the variations of spark timing, fuel injection position and fuel injection rate (early injection, late injection) in a LPDi engine.

• 대한기계학회논문집B
• /
• 제28권10호
• /
• pp.1178-1183
• /
• 2004

The purpose of this study was to investigate the influence of compression ratio on engine performance in a LPG(Liquefied Petroleum Gas) engine converted from a diesel engine. In ordor to determine the ideal compression ratio, a variable compression ratio 4-cylinder engine was developed. Retrofitting a diesel engine into a LPG engine is technically very complicated compared to a gasoline to LPG conversion. The cylinder head and the piston crown were modified to bum LPG in the engine. Compression ratios were increased from 8 to 10 in an increment of 0.5, the ignition timing was controlled to be at MBT(Minimum Spark Advance for Best Torque) for each case.

• 한국수소및신에너지학회논문집
• /
• 제28권6호
• /
• pp.642-648
• /
• 2017

The use of fossil is causing enviromental all over the world. So hydrogen energy is attracting attention as one of the alternative. The government announced that 30% of the air pollution is because of the Internal Combustion Engine Vehicle. In addition, they plans to reduce Internal Combustion Engine Vehicles by 2030 and increase (electric vehicles, EV) or (fuel cell vehicle, FCV). The FCV is evaluated as a next-generation green car because it has a long driving distance and short charging time. However, the hydrogen industry is not able to expand due to the lack of refueling infrastrucutre. This paper predicts the site of hydrogen refueling stations for the expansion of the hydrogen industry and proposes a method to supply hydrogen multi energy filling stations.