• Journal of Bio-Environment Control
• /
• v.13 no.3
• /
• pp.135-142
• /
• 2004

The objective of this study was carried out to determine which method is effective for improving seed germination in carrot and onion among osmotic or solid matrix priming. Seeds were osmotic primed with -0.5 MPa polyethylene glycol 8000 (PEG) solution and solid matrix primed with Micro Cel E (seed, Micro Cel E, and water mixed with the ratio of 4.0：2.0：8.0 by weight for carrot, and the ratio of 4.0：1.2：5.0 for onion at $20^{\circ}C$ for 4 days). Seeds were rapidly absorbed water after osmotic priming and solid matrix priming treatment. The moisture content of solid matrix primed seeds was lower than that of osmotic primed seeds in carrot and onion. Osmotic priming and solid matrix priming did not influenced on increasing of percent germination, but $T_{50}$ of treated seeds was shorter than those of untreated seeds at four temperature regimes. The effects of osmotic or solid matrix priming in reducing the $T_{50}$ was greater when the seeds were germinated at $15^{\circ}C$ than at $25^{\circ}C$ and $30^{\circ}C$ temperature. Solid matrix primed seeds germinated faster than osmotic primed seeds at all temperature in both carrot and onion. After priming, surface-dried seeds germinated faster than dried-back seeds in carrot and onion. Emergence speed of carrot and onion seeds was faster than untreated seeds by osmotic priming or SMP treatment although the final emergence percentage was not significantly influenced. On the other hand, early growth was not significantly influenced by osmotic priming or SMP treatment of carrot and onion seeds.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.99-99
• /
• 2017

국내 콩의 소비량은 계속적으로 증가하고 있다. 재배 면적은 1995년 10,000ha에서 2013년 8,000ha까지 계속적으로 감소하였으며, 수입은 2009년 644.9백만 달러에서 2013년 883.3백만 달러까지 계속적인 증가 추세에 있다. 건조는 품질 손상을 최소화 및 수분을 제거하는 공정이다. 모든 곡물에는 건조 조건에 따라서 품질이 크게 변화하며, 건조 과정을 해석하여 해당 곡물의 적정 건조 조건을 구명하여 품질을 유지하는 위해서는 중요하다(Keum, 등 1977). 얇은 두께의 곡물층을 단층으로 하여 건조속도 및 건조공기의 조건을 나타내는 것을 박층(Thin layer)건조모델이라 한다. 박층건조모델을 계속적으로 쌓은 모델을 후층(Deep layer)모델이라 하며, 건조기 개발 및 건조조건 구명에 가장 기본이 된다(Basunia and Abe, 1998). 그러나 해외에서 만들어진 콩 박층건조 모델은 국내의 검은콩과 물성이 상이하여 건조조건이 다르게 설정 되어야 한다. 따라서, 본 연구목적은 건조온도 2수준, 상대습도 3수준에 대하여 검은 콩의 건조속도 측정하고, 곡물건조방정식으로 많이 이용되고 있는 4개의 건조방정식에 대하여 모델 적합성을 검정하여 검은콩 건조에 적합한 박층건조모델 결정하는데 있다. 공시재료는 2015년 강원도지역에서 생산된 검은콩을 실험에 사용하였으며, 초기 함수율은 14.7%,w.b.였다. 박층 건조공기 조성은 공기조화장치(MTH4100, SANYO, UK)를 사용하여 조성하였으며, 송풍기에 의해 공기충만실을 통과하여 건조 층을 통과하도록 구성하였다. 목표 평형함수율에 도달하면 실험을 종료하였다. 건조 층의 초기중량 및 경시적 변화는 전자저울(GF-4000, AND, Japan)을 이용하여 10분 간격 측정하여 저장하였다. 적정 박층건조모델을 결정하기 위하여 기존의 곡물건조방정식 중 널리 사용되고 있는 4개(Lewis, 1921; Page, 1949; Thompson, 1967; Moisture diffusion, 1975)의 건조모델을 이용하여 비교 검증하였다. 건조 초기 2시간 까지는 급격히 감소하다가 건조속도에 영향을 미치는 반건조시간(MR=0.5) 이후에는 완만하게 건조되는 것으로 나타났고 건조조건으로 건조온도 및 상대습도 모두의 영향이 미치는 것으로 나타났다. 4가지 건조 모델과 비교한 결과 Thompson 모델이 전체 건조 영역에서 비교적 잘 일치하였다.

• Journal of Korean Society of Forest Science
• /
• v.72 no.1
• /
• pp.37-44
• /
• 1986

Seasonal changes of water relations parameters were obtained from p-v curves in leaves of Quercus grosseserrata and Quercus acutissima. The osmotic pressure at full hydration, ${\pi}_o$, and osmotic pressure at incipient plasmolysis, ${\pi}_p$, were high in newly emerged leaves but decreased with leaf development in each of the species. Water deficit at turgor loss was 10 to 20% in each of the species during the growing season. Maximum bulk elastic modulus in cell walls at full turgor, Emax, rises rapidly with leaf development before senescence in each of the species. Seasonal change of number of osmoles solute in symplasm per dry weight, Ns/DW, was higher in Quercus grosseserrata leaves than Quercus acutissima leaves, while relative water content (Vp/Vo, $RWC^*$, Vo/Vt) was relatively constant in each of the species.

• Journal of Bio-Environment Control
• /
• v.18 no.3
• /
• pp.238-243
• /
• 2009

To investigate the characteristics of moisture content (MC), moisture distribution and starting point of drainage in a rockwool slab culture, time domain reflectometry (TDR) sensors were used in a drip irrigation system. MC values ($0{\sim}100%$) measured by TDR sensors in a slab were compared to those by loadcells. Seventy two seedlings of paprika (Capsicum annuum L.) were cultured for $5{\sim}6$ months in a green-house and the starting point of irrigation was determined by the average value of three TDR sensors which were inserted diagonally across the slabs under the plants. MCs as a standard for starting point of irrigation by TDR were determined with 40%, 50%, and 60%. Distribution of MCs in a slab measured with five TDR sensors equally spaced from two irrigation points were not much different when the MC in the slab increased from zero to saturation point. The saturated MCs in the slab were presented at $58{\sim}65%$ and the drain was started when the MC became around $50{\sim}55%$. At the saturated MC in the slab, TDR sensors presented 100% but the values from the loadcell showed 90% at the same time. However, measurement errors between two methods for MC remarkably decreased with a decrease in the MC in a slab. Especially when the MC was maintaining below 60%, the errors between TDR and loadcell methods for measuring MC in the rock-wool slab were less than 5%. There were no significant differences in number of fruits and fresh and dry weights of fruits when they were cultured under the different MC conditions with three irrigation regimes (40%, 50%, and 60%). These results indicated that the MC control by TDR sensors in a rock-wool based paprika culture can be suggested as a method to determine the starting point of irrigation for a soilless culture system.

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2011.03a
• /
• pp.61-61
• /
• 2011

지구 온난화로 인해 환경파괴, 병원성 세균 감염 등에 의한 각종 질병과 아토피 피부염 등 수없이 많은 요소들에서 우리 몸을 보호하기 위하여 친환경 소재의 용품들이 각광 받고 있다. 이중에서도 키토산과 칼슘알지네이트는 천연재료로써 이미 다른 분야에서 응용되어 사용되고 있으며, 이 두 가지 천연재료를 두 층으로 면섬유에 코팅시킨 CCAC섬유를 제조하였다. CCAC섬유와 키토산이 코팅된 면섬유, 칼슘알지네이트가 코팅된 면섬유, 미처리 면섬유의 총 4가지 섬유에 체액, 증류수, 생리식염수의 각각의 조건에서 흡습량, 흡습시간을 측정하여 비교하고, 수분율과 함수율을 측정하고, 접촉각을 Contact angle system OCA20을 이용하여 측정하였다. CCAC섬유의 키토산 부착 함량을 알아보기 위하여 정량적인 방법으로 add-on율을 이용하여 확인하고, 정성적인 방법으로 원소분석기(Elemental Analyzer, FLASH 1112)를 이용하여 측정하였다. 칼슘알지네이트의 함량 분석은 EDS(EX-250, HORIBA, Japan)를 이용하여 측정하고, 직물의 표면과 단면의 형태는 주사전자현미경(S-4100, Hitachi Co., Japan)으로 ${\times}100$, ${\times}1000$ 배율로 측정하여 단면과 표면 상태를 확인하고, 물리적인 특성은 KES-FB system 을 통하여 확인 하였다.

• Journal of the Korean Wood Science and Technology
• /
• v.35 no.1
• /
• pp.11-16
• /
• 2007

This study was carried out to investigate the effect of Vapor-dam treatment on drying drying rates, prevention of checks and V-shaped split during air circulating oven drying bamboo (Phyllostachys pubescens Mazel et Z) tube. It was shown that the drying time from green to around 7~8 % of moisture content was required less as drying schedule was more severe, and distinctly dominated by the drying rate during the initial drying stage. Area shrinkages in cross section and thickness shrinkages measured during air circulating oven drying test were very large. Surface checks and V-shaped splits were occurred in untreated samples just after the beginning of drying, while sixty seven percentages of all the Vapor-dam treated samples could be produced without drying defects. The V-shaped splits occurred in the Vapor-dam treated samples were influenced more by the sealing of the vapor evaporation through the cross section than drying schedule.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2016.05a
• /
• pp.281-281
• /
• 2016

기후변화로 인한 기상학적 자연재해로부터 대비하고 안정적인 용수공급을 위해 유역의 다양한 수문 요소들에 대한 분석 필요성이 증가하고 있다. 계절적 강수량의 편차가 큰 우리나라는 유역 통합 물관리가 중요하며, 효율적 수자원 관리와 물안보 확보를 위해 유역내 물순환을 이해하는 것이 중요하다. 유역의 유출을 결정하는 요소들에는 강우, 증발산량, 토양 수분 및 지하수 등이 있으며, 시간적으로는 홍수와 같이 단기에 발생하는 유출과 장기적으로 발생하는 유출이 있다. 장기 유출은 단기 유출에 비해 토양내 수분량이 무시할 수 없을 정도로 영향을 미치게 되므로, 1년 이상의 장기 유출 해석을 위해서는 강우가 발생하지 않는 기간 동안의 토양 수분량 변화와 증발산 영향을 고려할 필요가 있다. K-water에서 자체 개발된 분포형 장단기유출 모델인 K-DRUM은 유역을 격자(grid)단위로 구분하고 각 셀들에 대한 매개변수는 흐름방향도, 표고분포도, 토지이용도, 토지피복도 등을 GIS처리하여 일괄 입력할 수 있도록 함으로써 매개변수 산정과정에서 문제가 되는 경험적인 요인을 제거하였다. 흐름의 구분은 얕은면 흐름, 지표하 흐름, 지하수 흐름으로 구분하여 운동파법과 선형저류법을 적용하였다. 또한 초기 토양함수 자동보정기법으로 실제의 기저유출량을 재현하여 전체적인 유출모의 정확도를 높였으며, FAO-56 Penman-Monteith법을 적용한 증발산량 산정모듈과 Sugawara et al.(1984)이 제안한 개념적 융설 및 적설모듈을 추가하였다. K-DRUM모형을 이용한 유출분석은 용담댐 시험유역을 대상으로 2013년도 1년간의 유출모의를 수행하였다. 입력자료는 용담댐 유역의 지형, 토양 및 토지특성 정보와 시단위 강우 및 기상정보(온도, 바람, 일사 등)를 활용하였다. 분석 결과, 총 관측유출량은 7,151 ㎥/s이고 총 계산유출량 $8,257m^3/s$이며, 관측유출량 대비 계산유출량은 약 115% 정도로 나타났다. 연간 총 강우량은 1303.5 mm로 유역면적 약 $930km^2$을 적용하여 유역 총 강우량을 산정하면 $14,030m^3/s$로서 관측유출량은 유역 총 강우량 대비 51%이고 계산유출량은 59% 정도로 나타났다. 즉 유역 유출율은 약 51% 수준으로 보통의 유역과 유사한 수준이다. 관측된 토양수분량과 K-DRUM 모형의 계산된 토양수분량을 비교하기 위하여 관측 토양수분량의 비율을 이용하여 비교하였다. 모의결과 토양수분은 강우에 의해 변화하며, 관측결과와 유사한 형태로 나타남을 알 수 있었다.

• Korean Chemical Engineering Research
• /
• v.53 no.2
• /
• pp.224-230
• /
• 2015

This study was conducted to investigate the effects of several variables on the durability of wood pellets fabricated with torrefied larch (LAR) and tulip tree (TUT) chips. Microscopic observation by scanning electron microscope-energy dispersive X-ray spectrometer was also performed to identify the surface of the wood pellets visually. In addition, torrefied-LAR and TUT pellets were fabricated with the addition of moisture, lignin, starch and protein as binders, and durabilities of the pellets were analyzed statistically. Durabilities of torrefied-LAR and TUT pellets were lower than one of non-torrefied-LAR and TUT pellets. Durabilities of both pellets fabricated with the wood chips, which were torrefied with $230^{\circ}C$ and 30 min, were the highest among all torrefaction conditions used in this study. From the microscopic observations, lignin was distributed broadly on the surface of non-torrefied wood pellets, whereas congregated partially on the surface of torrefied wood pellets. Durability of LAR pellets increased with the addition of moisture, but that of TUT pellets was reduced. Addition of binders contributed to increase the durability of LAR and TUT pellets. As a binder, lignin and protein were more effective than starch for improving the durability. In conclusion, mild torrefaction treatment, such as $230^{\circ}C$ and 30 min, might be an optimal condition to minimize the durability reduction of the LAR and TUT pellets. In addition, when torrefied woody materials with high and low specific gravities are used as a raw material for the production of durable wood pellets, it might be required to adjust moisture content and torrefaction conditions of woody materials, respectively.

• Proceedings of the KSME Conference
• /
• 2000.11b
• /
• pp.526-531
• /
• 2000

Application of electrodewatering (EDW) to mechanical dewatering system was studied to decrease water content in the sludge generated from waste water treatment process. Experiments realized the reduction of water content in the sewage sludge. EDW enhancing the conventional filtration by an electric field is an emerging technology with the potential to improve dewatering. In this study, a piston filter press was constructed, the digested sludges were dewatered by EDW under conditions of DC electric field and constant pressure in the piston filter press. Constant electric field from $0{\sim}120\;V/cm$ and constant pressure $98.1{\sim}392.4\;kPa$ were used. The results showed that as electric field was increased the dewatering rates increased and as pressure was increased the dewatering rates decreased. Also as polymer was added the dewatering rates increased. This experiments produced final sludge cake with water content of 60 wt% using EDW, compared with 80 wt% using pressure filtration alone.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.21 no.4
• /
• pp.236-242
• /
• 2009

In finishing work, defects are often taken place by many factors. One of them is the thermo-humidity condition on the work surface as coating and anointing adhesives. Thus, the condition of thermo-humidity on work surface should be checked prior to the finishing work. However, many construction companies show a tendency to overlook it because not only are measurement tools so expensive but they don't have skilled hands about those tools. Therefore, we propose the measurement method that makes it easy to recognize surface thermo-humidity condition so as to reduce constructional flaws. And then we test this product. The test progresses to four stages with various conditions. We evaluate its usefulness and application possibility of this product in the field.