• Journal of agriculture & life science
• /
• v.53 no.5
• /
• pp.137-143
• /
• 2019

To manufacturing of solid fuel by reuse of the wastes, the drying unit which have 500 kg/hr of drying capacity was developed and experimentally evaluate the performance. The spinach grown in Nam-hae island were used for the experiments and investigated of the heated-air drying characteristics as the inlet amount of raw materials, raw material stirring status, conveying type and drying time. The drying air heated by the energy derived from the steam which is supplied from the incineration plant. The moisture contents of raw materials were measured 85.65%. The inlet flow rate of drying air made a difference as the depth of the raw materials loaded on the drying unit and temperature has showed 108~144℃. The drying speed of the mixed drying more than doubled as that of non mixed drying under the same drying type, inlet amount, drying time and drying air temperature. In each experiment, the drying capacity have showed over 500 kg/hr. A drying efficiency of the ratio of drying consumption energy to input energy was 33.46%, lower than the average of 57.76% for the 157 conventional dryers. Because developed dryer must have a drying time of less than one hour, it is considered that the dry efficiency has been reduced due to the loss of wind volume during drying. If waste heat from incineration plant is used as a direct heat source, the dry air temperature is expected to be at least 160℃, greatly improving the drying capacity.

• Journal of Bio-Environment Control
• /
• v.32 no.2
• /
• pp.165-171
• /
• 2023

Potato dry rot is one of the potato storage diseases caused by Fusarium species and is a representative pathological disorder that induced post-harvest loss during storage. Chlorpropham treatment for sprouting inhibition is mainly used for room temperature storage of potatoes for processing. In this study, the inhibitory effect of chlorpropham on Fusarium-induced dry rot of potato 'Dano'. To investigate the mycelial growth rate of the dry rot fungus (Fusarium solani Appel & Wollenw), mycelial growth was investigated in a chlorpropham (5.0, 50.4, 503.8, and 5,038 ppm) and prochloraz (0.1, 1.0, 10.0, and 100.0 ppm) medium containing F. oxysporum mycelia. Mycelia were more inhibited as the concentration of chlorpropham and prochloraz increased during incubation at 20℃, and the inhibition rate was 98.2% and 100% when treated with 503.8 ppm of chlorpropham and 10ppm of prochloraz in 14 days, respectively. Potato Dano tubers inoculated with F. oxysporum were dipped in chlorpropham (5.0, 50.4, and 503.8 ppm) and prochloraz (100 ppm) to investigate the effect of preventing dry rot during cold storage at 20℃ and 4℃ in vivo. The disease diameter of potatoes stored at room temperature (about 20℃) was reduced to 13.0 mm in the prochloraz 100 ppm teatment, and 10.7 mm in the chlorpropham 50.4 ppm treatment compared to 13.7 mm in the control tuber at 70 days of storage. The disease progression in all treatments including control was similar with no statistically significant difference at 4℃ air temperature. From the results of this study, it is considered that treatment with 50.4 ppm of chlorpropham after harvest will be useful for suppressing dry rot of stored potatoes.

• Korean Chemical Engineering Research
• /
• v.61 no.3
• /
• pp.426-438
• /
• 2023

Lithium-sulfur batteries, recently attracting attention as next-generation batteries, have high energy density but are limited in application due to sulfur's insulating properties, shuttle phenomenon, and volume expansion. This study used an economical and simple vacuum filtration method to prepare a freestanding electrode without a binder and collector. Carbon nanotubes (CNTs) are used to improve the electrical conductivity of sulfur, where CNT also acts as both collector and conductor. In addition, metal oxides (MO_x, M=Ni, Mg), which are easy to adsorb lithium polysulfide, are added to the CNT/S electrode to suppress the shuttle reaction in lithium-sulfur batteries, which is a result of suppressing the loss of active sulfur material due to the excellent adsorption of lithium polysulfide by metal oxides. The MO_x@CNT/S electrode exhibited higher capacity characteristics and cycle stability than the CNT/S electrode without metal oxides. Among the MO_x@CNT/S electrodes, the NiO@CNT/S electrode displayed a high discharge capacity of 780 mAh g^-1 at 1 C and an extreme capacity decrease to 134 mAh g^-1 after 200 cycles. Although the MgO@CNT/S electrode exhibited a low discharge rate of 544 mAh g^-1 in the initial cycle, it showed good cycle stability with 90% of capacity retention up to 200 cycles. Further, to achieve high capacity and cycle stability, the Ni_0.7Mg_0.3O@CNT/S electrode, mixed with Ni:Mg in the ratio of 0.7:0.3, manifested an initial discharge rate of 755 mAh g^-1 (1 C) and a capacity retention rate of more than 90% after 200 cycles. Therefore, applying binary metal oxides to CNT/S provides a freestanding electrode for developing economical and high-performance Li-S batteries, effectively improving lithium polysulfide's high capacity characteristics and dissolution.

• Korean Journal of Heritage: History & Science
• /
• v.55 no.4
• /
• pp.180-193
• /
• 2022

The East Nine Royal Tombs is a representative place in the Royal Tombs of Joseon (a World Heritage Site). It consists of 1,289 stone artifacts including 979 related stone structures, 310 stone statues, and objects. Most of the stone structures in the East Nine Royal Tombs are composed of biotite granite, but some tombs are composed of light red granite. As a result of magnetic susceptibility measurement, the average data from Geonwolleung to Mongneung, excluding Hyeolleung, were similar, so it is estimated that stones were obtained from the same quarry. In the case of Sungneung, Sureung, and Gyeongneung, the range of susceptibility measurement is widely distributed. It assumed that the newly produced stones were mixed in the moving and construction process. Also, stones might be gathered from different quarries. As a result of a conservation status investigation, both the mound member and the ridge stone had the highest damage rate due to peeling and granular decomposition according to surface weathering. In the case of surface discoloration, yellowing and soils were found in the burial mound members. Yellowing, blackening, and soil were identified in the ridge stone structures. Bio-degradation is the major factor of deterioration of the East Nine Royal Tombs and the conservation status of the tombs were detected as grades 4 to 5. It seems that it is easy for the environment of the royal tombs to form soil for the microorganisms and fine conditions for continuous moisture. In the case of structures, they are in relatively good condition. As a result of a comprehensive damage rating for each tomb, the overall condition is good, but the Geonwolleung Royal Tomb and Hyeolleung Tomb, which were created in the early period, had relatively high weathering ratings. Stone objects in East Nine Royal Tombs have lost many pieces and gateway members due to surface deterioration. Also, secondary damage is ongoing. Each damage factor of the stone artifacts of the East Nine Royal Tombs combines to cause various and continuous damages. Therefore, it is necessary to establish regular conservation status data of the stone artifacts for efficient management after processing as well as conservation treatment of the royal tombs, and specific management manuals and systems. This study investigated the conservation status of stone structures in the East Nine Royal Tombs, a World Heritage Site, and systematically classified them to provide priority and necessity for conservation processing. We look forward to establishing a plan for the conservation and management of the East Nine Royal Tombs with this database in the future.

• Food Science and Preservation
• /
• v.30 no.1
• /
• pp.88-97
• /
• 2023

As livestock consumption in Korea has been gradually increasing, the quality of the final products has been improved to meet this increased demand. In particular, maintaining the water holding capacity (WHC) and minimizing the drip loss during the thawing of frozen meat are of utmost importance. This study investigated the physicochemical properties of frozen pork subjected to thawing under different conditions: at room temperature (20℃, under air), at a low temperature (4℃ refrigerator, under air), under water (20℃, under water in a vacuum bag), under microwave (microwave-thawing, 260 W), and under low-pressure tumbling (20℃, 0.015 bar, tumbling). The shortest thawing time for frozen pork was recorded upon low-pressure tumbling thus indicating a fast heat transfer. The lowest drip loss (0.2%) and highest WHC (94.5%) were also recorded under this condition. A significantly higher drip loss was observed upon microwave- (1.0%) and water-thawing (1.2%), which resulted in the lowest WHC in microwave thawing (87.2%). The highest total count of aerobic bacteria and coliform group were observed upon room temp thawing while the low pressure tumbling and thawing resulted in the lowest aerobic bacteria (1.90 log CFU/g) and coliform (0.78 log CFU/g) count. Consequently, thawing by low pressure tumbling afforded the best food quality.

• Journal of Preventive Medicine and Public Health
• /
• v.6 no.1
• /
• pp.51-63
• /
• 1973

This paper illustrate residual hearing and socio-medical background on the hearing impaired children, 207 comming to Deaf School. attached to Hankuk Social Work College, Taegu, Korea. The survey was performed through interview with their parents and testing by diagnostic audio-meter (TRIO, AS 105 type) at soundproof room from March 10, to November 28, 1973. The results obtained were as follows. 1) The attendance rate of the compulsory primary school was markedly lower tendency in female than male according to directly proportional to prevalence rate of deafness among them. If was showed the deeper gap in the more superior school (middle and high school). 2) Who entered at the suitable age to each school (six years old to primary school, 12 years to middle and 15 years to high) was 11.3%. And who were enrolled in school age to each school (6-11 years for primary. 12-14 years for middle and 15-17 years for high) was 45.9% (43.7% in male, 50.0% in female). 3) As causative disease, congenital case, were 23.6% included of 13.5% of heredity and 10.1% of troubles during pregnancy; the total acquired cases were 47.9%, it was classified as 11.6% of convulsion from any other diseases, 7.7% of measles, 7.7% of other febrile diseases, 3.4% of drug (the most of streptomycin) intoxication, 2.4% of meningitis, 1.5% of epidemic encephalitis and 31.3% of other diseases; and unknown cases were 28.5%. 4) 31.4% of who included congenital cases lost their hearing within six months old, 11.6% in 6-11 months. 9.7% in 1-2 years old and 14.0% in 2-3years old. Consequently we obtained that the most cases 90.0% were lost their hearing within 3 years after birth. 5) According to qualities of hearing leases the most of cases were perceptive, 197(97.5%), only two cases were conductive, and eight cases were mixed. 6) The status of residual hearing according to average grade of hearing loss. $B(=\frac{a+2b+c}{4}$ as table 13) were as follows. Two cases were normal (one was mute and another was severe speach disorder). Ten cases, moderate. Moderately severe cases were 40 (19.3%). Severe cases, 38(18.4%). Scale out, profound cases, 48 (23.3%). And impossible testing cases because that were infantile or had some mental disorder were 69 (33.3%). 7) The using rate of hearing aides was only 12.0%. Among them who had some more residual hearing and could showed hearing effect with hearing aide have used more many proportionary but who were difficult to expect that effect were rare.

• Journal of Animal Science and Technology
• /
• v.45 no.1
• /
• pp.69-78
• /
• 2003

This experiment was carried out to evaluate the value of total mixed fermentation feeds(TMFF) as completely mixed ration and to observe the effect of various kinds of TMFF on the palatability, feed intake, and milk performance in Holstein cows. The dry matter (DM) content of TMFF used in the experiment was 23.98-28.42% range, and CP, TDN, ADF and NDF were 16.2${\sim}$19.2%, 58.3-65.1%, 34.4-39.6% and 46.9${\sim}$49.9% levels, respectively. The relative feed value (RFV) in rape-, alfalfa-, grass-, oat-, corn-TMFF groups were 138.6, 133.9, 116.5, 111.8, 111.4 and 108.1, respectively. Among these groups, RFV of rye-TMFF group was lowest. Dry matter disappearance(DMD) showed 0.8${\sim}$.9% to the all kinds of TMFF groups. The pH was 3.89${\sim}$.87 and $NH_3$-N concentration was 6.93-8.66 mg/$d\ell$. The acetic acid concentration in the raw material of TMFF showed low level of 0.19${\sim}$0.57%, lactic acid showed high level of 1.17${\sim}$3.21% and butyric acid was very high as 0.03${\sim}$0.32%. Therefore, these results provide evidence that the quality of TMFF was not so bad. In the daily fresh matter intake on the alfalfa-, grass-, rape-, corn-, oats- and rye-TMFF were showed 62.85, 60.48, 58.04, 57.11, 54.61 and 45.74 kg respectively. All TMFF showed high palatability as daily dry matter intake of 1.95 to 2.90% by body weight of experimental cows. Body condition score(BCS) was gradually increased in during 60 days of the experiment term. Average daily gain(ADG) showed about 140.0${\sim}$326.7g. In alfalfa-TMFF group, the ADG was higher than in the other groups (p<0.05). Also, the increase in BCS was observed in grass-TMFF group (3.07 to 3.34) and rye-TMFF group was decreased in 3.07 to 3.34 (p<0.05). The milk yield appropriately showed a range of 16.16${\sim}$18.95 kg in all groups. Among these groups, alfalfa-TMFF group was highest(P<0.05). Average milk fat contents showed high levels of 4.06${\sim}$4.79% and the level was high in order of rape-, grass-, corn-, alfalfa-, rye- and oats-TMFF. Milk protein was highest in forage-TMFF and level of lactose in milk was approximately 4.56% in overall groups. Solid non fat(SNF) and total solid(TS) contents were 8.75% and 12.8%, respectively. However, milk composition was not significantly affected by TMFF.

• The Korean Journal of Nuclear Medicine
• /
• v.38 no.3
• /
• pp.259-267
• /
• 2004

Purpose: NEMA NU2-2001 was proposed as a new standard for performance evaluation of whole body PET scanners. in this study, system performance of Siemens CTI ECAT EXACT 47 PET scanner including spatial resolution, sensitivity, scatter fraction, and count rate performance in 2D and 3D mode was evaluated using this new standard method. Methods: ECAT EXACT 47 is a BGO crystal based PET scanner and covers an axial field of view (FOV) of 16.2 cm. Retractable septa allow 2D and 3D data acquisition. All the PET data were acquired according to the NEMA NU2-2001 protocols (coincidence window: 12 ns, energy window: $250{\sim}650$ keV). For the spatial resolution measurement, F-18 point source was placed at the center of the axial FOV((a) x=0, and y=1, (b)x=0, and y=10, (c)x=70, and y=0cm) and a position one fourth of the axial FOV from the center ((a) x=0, and y=1, (b)x=0, and y=10, (c)x=10, and y=0cm). In this case, x and y are transaxial horizontal and vertical, and z is the scanner's axial direction. Images were reconstructed using FBP with ramp filter without any post processing. To measure the system sensitivity, NEMA sensitivity phantom filled with F-18 solution and surrounded by $1{\sim}5$ aluminum sleeves were scanned at the center of transaxial FOV and 10 cm offset from the center. Attenuation free values of sensitivity wire estimated by extrapolating data to the zero wall thickness. NEMA scatter phantom with length of 70 cm was filled with F-18 or C-11solution (2D: 2,900 MBq, 3D: 407 MBq), and coincidence count rates wire measured for 7 half-lives to obtain noise equivalent count rate (MECR) and scatter fraction. We confirmed that dead time loss of the last flame were below 1%. Scatter fraction was estimated by averaging the true to background (staffer+random) ratios of last 3 frames in which the fractions of random rate art negligibly small. Results: Axial and transverse resolutions at 1cm offset from the center were 0.62 and 0.66 cm (FBP in 2D and 3D), and 0.67 and 0.69 cm (FBP in 2D and 3D). Axial, transverse radial, and transverse tangential resolutions at 10cm offset from the center were 0.72 and 0.68 cm (FBP in 2D and 3D), 0.63 and 0.66 cm (FBP in 2D and 3D), and 0.72 and 0.66 cm (FBP in 2D and 3D). Sensitivity values were 708.6 (2D), 2931.3 (3D) counts/sec/MBq at the center and 728.7 (2D, 3398.2 (3D) counts/sec/MBq at 10 cm offset from the center. Scatter fractions were 0.19 (2D) and 0.49 (3D). Peak true count rate and NECR were 64.0 kcps at 40.1 kBq/mL and 49.6 kcps at 40.1 kBq/mL in 2D and 53.7 kcps at 4.76 kBq/mL and 26.4 kcps at 4.47 kBq/mL in 3D. Conclusion: Information about the performance of CTI ECAT EXACT 47 PET scanner reported in this study will be useful for the quantitative analysis of data and determination of optimal image acquisition protocols using this widely used scanner for clinical and research purposes.

• Journal of Korean Society of Forest Science
• /
• v.56 no.1
• /
• pp.1-25
• /
• 1982

Plywood used for construction as a decorative inner material is inflammable and can cause fire accidents. causing destruction of human life and property. To diminish the fire disaster, fire retardant plywood is indeed required. In the methods of manufacturing the fire retardant plywood, a soaking method is occasionally used. However after soaking plywood into fire retardant chemical solutions redrying of soaked plywood is of the utmost importance. In this study 3.5mm and 5.0mm thickness plywoods were selected for fire retardant treatment. Treating solutions were prepared for 20% dilute solutions of ammonium sulfate, monoammonium phosphate, diammonium phosphate, borax-boric acid minalith, and water solution, 1-, 3-, 6-, and 9 hour-soaking treatments in borax-boric acid and minalith, and 6- and 9 hours in the other chemicals were applied and after the treatment hot drying was applied to treated plywoods at $90^{\circ}C$, $120^{\circ}C$ and $150^{\circ}C$ of press temperature. Drying rates, drying curves, water absorption rates of fire retardant chemicals, weight per volume and fire retardant degree of plywood were investigated. The results may be summarized as follows: 1) In the 9 hours-soaking treatment of fire retardants by hot and cold bath method, the chemical retentions of 3.5mm thickness plywood could be attained within the range ($1.125-2.25kg/(30cm)^3$) of minimum retention specification as follows: $1.353kg/(30cm)^3$ in monoammonium phosphate, $1.331kg/(30cm)^3$ in diammonium phosphate, $1.263kg/(30cm)^3$ in ammonium sulfate, $1.226kg/(30cm)^3$ in borax-boric acid. But the chemical retention, $0.906kg/(30cm)^3$, in minalith could not be attained within the range of minimum retention specification. And also in case of 5.0mm thickness plywood, chemical retentions, as $1.356kg/(30cm)^3$ and $1.166kg/(30cm)^3$ respectively, of ammonium sulfate and diammonium phosphate could be attained within the range minimum retention specification, but the other fire retardant chemicals could not. 2) In the 6- and - hours-soaking treatments of 3.5mm and 5.0mm thickness plywood, the drying curve sloped of chemical treated plywood was smaller than that of water treated. The drying rate related to thickness of treated plywood, was about three times as fast in 3.5mm thickness plywood compared with 5.0mm thickness plywood. 3) In the treatment at $120^{\circ}C$ of hot platen temperature, the drying rates of chemical-treated plywood showed the highest quantity in diammonium phosphate of 3.5mm and 5.0mm thickness plywood. But the drying rate of water treated plywood was highest during the 6- and 9 hours-soaking treatments. 4) The drying rate remarkably increased with proportion to increase of the platen temperature, and the values were respectively 1.23%/min., 6.54%/min., 25.75%/min. in hot platen temperature of $90^{\circ}C$, $120^{\circ}C$, $150^{\circ}C$ in 3.5mm thickness plywood and 0.55%.min., 2.49%/min., 8.19%/min. in hot platen temperature of $90^{\circ}C$, $120^{\circ}C$, $150^{\circ}C$ in 5.0mm thickness plywood. 5) In the fire retardant degree of chemical treated plywood, the loss in weight was the smallest in diammonium phosphate, next was in monoammonium phosphate and ammonium sulfate, and the greatest was in borax-boric acid and minalith. And the fire-retardant effect in burning time, flame-exhausted time and carbonized area were greatest in diammouniun phosphate, next were in monoammonium phosphate and ammonium sulfate, and the weakest were in borax-boric acid and minalith.

• Journal of Korean Society of Forest Science
• /
• v.52 no.1
• /
• pp.37-49
• /
• 1981

The purpose of the study is to find out the objective method of valuation on the forest stands through the analysis of logging costs that is positively related to timber production. The two forest (Amgog, Whangryoung), located nereby, but forest type, logging and skidding conditions being slightly different, were slected to carry out the study. The objective timber stumpage value were determined by investigating the appropriate timber production costs and profits of logging operations. The main result obtained in this study are as follows: 1. The rate of logging cost in consisting of timber market price is 13.15% in the area of Amgog logging place and 19.48% in Whangryoung. 2. The rate of the other production cost excluding logging cost is 15.36% in the area of Amgog logging place and 28.85% in Whangryoung. 3. The total rate of timber production cost in consisting of the market price is more than 28.51% in the area of Amgog logging place and 48.33% in Whangryoung, 4. Though the productivity of forest land is affected by the selection of tree species, tending, treatments and effective management of forest land, the more important problem is improvement of logging condition. 5. The rate of production cost in timber price is so high that we should endeavore to improve the productivity of labour and its quality, and minimize the difference of piece work per day in accordance to the various site condition. 6. Although the profit of forest industry is related to the period of recapturing investment, it is more closely related to the working condition, risk of investment and continuous change of social investment interest. 7. If the right variables which are related to the timber market, are objectively obtained, the stumpage value of mature forests can be objectively caculated by applying straight line discounting method or compound discounting method in caculating the stump to market price.