• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.593-596
• /
• 2008

Domestic area of most be happened chloride deicer damage. Because daily mean temperature is below 0$^{\circ}C$ from the area of domestic most. Use of deicing chemicals has been and will continue to be a major part of concrete structure in the highway. Chloride-containing chemicals such as calcium chloride or rock salt are main deicers for the road. Extensive use of chloride deicers is, however, not only the source of substantial cost penalties due to their corrosive action and ability to deterioration roadway surface materials but also the source of environmental damages. Chloride-containing chemicals such as calcium chloride or rock salt are main deicers for the road. Extensive use of chloride deicers is, however, not only the source of substantial cost penalties due to their corrosive action and ability to deterioration roadway surface materials but also the source of environmental damages. In this study, Use of deicing chemicals has been and will continue to be a major part of highway freeze-thaw durability and carbonation of concrete surface protecting materials

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.6
• /
• pp.113-131
• /
• 1998

The objective of the present study is to investigate the characteristics of the dividing flow in the laminar flow region. Using glycerine water solution(wt43%) for Newtonian fluid and the polymer of viscoelastic fluid(500wppm) for non-Newtonian fluid, this research investigates the flow state of the dividing tube in steady laminar flow region of the two dimensional dividing tube by measuring the effect of Reynolds number, dividing angle, and the flow rate ratio on the loss coefficient. In T- and Y-type tubes, the loss coefficients of the Newtonian fluid decreases in constant rate when the Reynolds number is below 100. The effect of the flow rate ratio on the loss coefficients is negligible. But when the Reynolds number is over 100, the loss coefficient with various flow rate ratios approach an asymptotic value. The loss coefficient of the non-Newtonian fluid for different the Reynolds number shows the similar tendency of the Newtonian fluid. And when the Reynolds number is over 300, the loss coefficient is approximately 1.03 regardless of flow rate ratio or the dividing angle. The aspect ratio does hardly influence the reattachment length and the loss coefficient of both Newtonian and non Newtonian fluid. The loss coefficient decreases as the Reynolds number increases. The loss coefficient of Newtonian fluid is larger than that of non-Newtonian fluid.

• Journal of Energy Engineering
• /
• v.13 no.4
• /
• pp.291-295
• /
• 2004

Heat regenerator attached in small-scale regenerative radiant tube burner was designed using the theoretical computation code and was confirmed the performance of waste heat recovery ratio. From the computation, when ceramic ball of 4-5kg was used, temperature efficiency and available waste heat recovery ratio were predicted 80% and 70%, respectively. Similar efficiencies were obtained from the experiments using LPG. However, since exhaust gas temperature entered into regenerator was below 850$^{\circ}C$ which was moth lower than that we expected. air preheating temperature was lowered below 800$^{\circ}C$.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2015.05a
• /
• pp.75-75
• /
• 2015

오염원과 취수장이 동일 구간 내에 공존하는 국내하천의 특성상, 하천 평면 내에서 오염물의 거동 및 혼합 특성을 보다 정확하게 해석하기 위해서는 2차원 이송-분산 모형의 적용이 필요하다. 이를 위해서는 2차원 모형의 주요 매개변수인 종분산계수와 횡분산계수의 적절한 입력이 매우 중요하다. 하지만 국내외적으로 횡분산계수에 대한 연구는 많이 진행된 반면, 현재까지 종분산계수에 대한 연구는 충분히 이루어지지 않은 실정이다. 분산계수를 결정하는 방법에는 실측된 농도 자료의 유무에 따라 크게 두 가지로 분류된다. 실측된 농도 자료가 없는 경우, 이론식이나 경험식을 이용하는 방법이 있다. 반면에 추적자 실험 등을 수행하여 실측된 농도 자료가 있는 경우, 모멘트법 또는 추적법을 적용하여 농도-시간 분포 곡선으로부터 분산계수를 계산하는 것이다. 모멘트법은 임의 지점에서 농도의 횡분포를 통해 얻을 수 있는 2차 모멘트의 종방향 변화율이 횡분산계수와 비례한다는 원리를 이용한 것이며, 추적법은 상류부의 관측된 농도를 입력자료로 하여 하류부의 농도를 계산한 후 계산된 농도와 실측된 하류부 농도의 비교를 통해 분산계수를 산정하는 방법이다. 본 연구에서는 불규칙한 단면 형상을 가지는 자연하천에서의 2차원 종 횡분산계수를 산정하기 위해서 Baek & Seo(2010)가 제안한 2차원 유관추적법(2D Stream-tube Routing Procedure)을 적용하였다. 본 연구에서는 국내 자연하천 중 다양한 사행형태를 갖으며 수질오염 사고의 위험이 높은 구간을 선정하고, 추적자로서 Rhodamine WT를 이용하여 현장실험을 수행하였다. 실험에서 수집된 수리량 및 농도자료로부터 추적자의 2차원적 거동을 분석하였으며, 2차원 유관추적법을 적용하여 종분산계수를 산정하였다. 그 결과 하폭 대 수심비(W/H)와 마찰손실관련 무차원변수(U/U*)의 증가에 따라 종분산계수가 증가됨을 확인 할 수 있었다. 본 연구에서 산출된 종분산계수와 선행 연구에서 수집된 자료를 이용하여 추정식을 개발하였다. 차원해석을 통해 무차원 종분산계수에 영향을 미치는 무차원 인자를 선별하고 회귀분석을 이용하여 종분산계수 추정식을 유도하였다. 추정식을 이용하여 산정한 종분산계수의 범위는 Elder (1959)가 제안한 이론값보다 약 10배 정도로 크게 나타났다. 혼합 특성이 밝혀지지 않은 자연하천에 2차원 확산모형을 적용하고자 할 때 본 연구에서 개발된 추정식으로부터 계산된 종분산계수를 사용할 수 있을 것이다.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2014.10a
• /
• pp.693-695
• /
• 2014

Radioactive isotopes for radiation diagnosis is production by using Cyclotron like a PET. Radioactive isotopes is influenced product yield according to shape and size of the proton beam and target irradiation position by cyclotron. And to develop a device for measuring the distribution of the beam to increase the loss of the beam. Beam measuring device is measured vertically beam current according move the two wires. In this way, by using the beam current value in each position you are able to know the cross section and location information of the beam. By scanning cross-section for X-axis Y-axis of beam acquires data of beam. Print this into 2D graph, and analyze the result. You can save this result by documentation process.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.23 no.4
• /
• pp.28-34
• /
• 2019

In this study, pin-fin arrays, which are widely used for cooling turbine blades, were studied. The vortex generator in pin-fin arrays is located in front of the circular tube. The cross-section of the vortex generator is NACA-9410. The purpose of this study is to analyze heat transfer performance and flow characteristics of pin-fin arrays. The position of vortex generator is changed with the vertical flow direction on the bottom wall. Pin-fin arrays were calculated with 6000, 10000 and 15000 Reynolds number. The commercial program ANSYS v18.0 CFX and the turbulence model $k-{\omega}$ SST were used. As a result, the heat transfer performance increased up to 5.8% and pressure loss increased less than 1%.

• Journal of the Korean Wood Science and Technology
• /
• v.32 no.2
• /
• pp.50-57
• /
• 2004

This study attempted to evaluate the water repellency and drying effectiveness of linseed oil treated-solid wood at high temperature by immersion. The moisture content of green wood (Pinus densiflora) sample (above 90%) was reduced about 10% after 6 hours treatment at 150℃. When the treated samples were cut into cross section along the length, it was observed that the linseed oil penetrated into up to 20% of the sample cross section area in all locations. However, a strength loss of the specimen was not detected. The pre-drilling before linseed oil treatment was effective in reducing the defects such as checks and splits, and improved the linseed oil penetration into all samples from the surfaces. The result of water absorption test of treated-wood showed that the water repellent efficacy of treated-wood was greater than that of the control. The anti-fungal activity of treated samples using five sap stains and thee decay fungi was not detected in broad-spectrum toxic mechanism. However, decay test using white rot fungi (Tyromyces palustris) and brown rot fungi (Trametes versicolor) showed that the treated sample has a decay resistance to these two fungi.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2022.05a
• /
• pp.409-409
• /
• 2022

환경부 홍수통제소의 경우는 전국단위의 강수량(지상, 레이더), 하천수위, 유사량 관측과 국부적으로 증발산량과 토양수분 관측이 이루어지고 있는 상황이며, 기상청 및 다른 공공기관도 각 목적에 맞게 수문기상관측이 이루어지나 유역(또는 지역) 단위의 물순환 과정(강우량, 유출량, 증발산량, 지하수함양량, 토양수분량 등 포함)을 규명하는 조사·연구는 매우 미비한 실정이다. 개별적인 물순환 성분별 수문조사에서 벗어난 전체적인 관점을 고려한 유역단위의 물순환 과정을 규명하는 것은 매우 중요하다. 즉 물순환 성분별 명확한 수문량 산정 결과는 수자원 개발과 물환경 보전에 중요한 정보를 제공할 수 있다. 따라서 물순환 성분별 명확한 분석을 위해서는 중·소규모 유역 단위를 대상으로 지속적이고 신뢰성 있는 자료의 획득과 축적이 중요하므로 중·소규모 유역 단위의 대표성 있는 시험유역의 운영은 매우 의미가 있다고 볼 수 있다. 본 논문에서는 한국건설기술연구원에서 운영하는 설마천 유역(전적비교 수위관측소 기준, 유역 면적 8.48km², 유로연장 5.59km, 유로경사 2.15%, 경기도 파주시 적성면 소재)의 2021년 수문관측자료를 이용하여 지표수 물순환 성분인 강우량, 하천유출량, 증발산량을 산정하였다. 기본 관측자료인 강우량은 각 지점강우량의 관측자료의 비교·검토 등 품질관리를 통해 자료를 확정하고 유역평균강우량을 산정하였다. 하천수위는 기준수위표와의 검토를 통해 자료를 확정하였으며, 하천유출량은 기존의 유량측정성과와 단면검토를 통해 수위-유량관계곡선식을 개발하고, 확정된 수위자료를 적용하여 산정하였다. 그리고 증발산량은 유역인근 2개 관측소(동두천 파주)의 기상관측자료를 이용하여 잠재증발산량을 산정하여 추정한 값이며, 그 외 지하수 함양량은 관측 지하수위자료의 결측으로 산정에서 제외하였다. 각 물순환 성분별로 생성된 2021년의 설마천 유역(전적비교 수위관측소 기준)의 총강우량은 1,103.6mm이며, 하천유출량은 620.1mm(총강우량 대비 56.2%), 실제증발산량(잠재증발산량 추정값)은 443.0mm(40.1%)이며, 그 외는 유역 손실량이다. 이와 같이 산정된 물순환 성분별 자료는 유역의 물순환 과정 규명을 위한 기초자료로 매우 유용하게 활용될 수 있으며, 유역 물관리를 위한 의사결정 과정에 중요한 역할을 할 수 있을 것으로 기대된다.

• Korean Journal of Soil Science and Fertilizer
• /
• v.28 no.2
• /
• pp.135-144
• /
• 1995

Understanding on nutrient solute movement during the course of freezing and thawing was attempted through laboratory and field obsevations. Small sectioned tubes with 5cm inner diameter, 0.2cm thick and 1cm long were connected to 30cm long soil columns for laboratory study. The columns were filled with soil, and treated with 20mmol/kg $KNO_3$ for upper 5cm. The upper end was set in the freezing section, and the lower end was set in the refrigerating section of a refrigerator. Temperature was controlled at $-7({\pm}1)^{\circ}C$ and $1.5({\pm}1)^{\circ}C$, respectively. After top 5cm soil was frozen, the columns were sectioned, and analyzed for $NO_3^-$, $NH_4^+$ and $K^+$. For field study, the 20cm inner diameter and lm long soil columns were installed in Chuncheon and Daegwanryung, where the altitude was 74m and 840m, respectively. The soils used were silt loam and clay loam. The top 20cm soils were treated with 50mmol/kg as $KNO_3$. The soil columns were taken during winter freezing and after thawing. By laboratiry study, upward movement of $NO_3^-$ and $K^+$ during the course of freezing was confirmed. The upward movement of $K^+$ was, however, one fifth to one tenth of $NO_3^-$. The upward movement of inorganic nitrogen as well as laboratory during the course of freezing, but large amount of nitrogen was lost from the profile after thawing in early spring. Leached nitrogen from the upper 20cm to lower part was 17 to 24 percents. The maximum depth of leaching during the experiment was 50cm for all soils. The net loss of inorganic nitrogen from the whole profile ranged 8.7 to 39.5 percents. The net loss was greater in Daegwanryung where temperature was lower and snowfall was larger than Chuncheon, and the loss was greater from the silt loam soil than clay loam soil of which percolation rate was small. The results implied that reasons for nitrogen loss during the winter might include surface washing by snow melt as well as leaching and denitrification.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.22 no.4
• /
• pp.347-365
• /
• 2020

In order to resolve traffic problems in urban areas and to increase the area of green spaces, tunnels in downtown areas are being increased. Additionally, the application of large port smoke extraction ventilation systems is increasing as a countermeasure to smoke extraction ventilation for tunnels with high potential for traffic congestion. It is known that the smoke extraction performance of the large port smoke extraction system is influenced not only by the amount of the extraction flow rate, but also by various factors such as the shape of the extraction port (damper) and the extraction air velocity through a damper. Therefore, in this study, the design standards and installation status of each country were investigated. When the extraction air flow rate was the same, the smoke extraction performance according to the size of the damper was numerically simulated in terms of smoke propagation distance, compared and evaluated, and the following results were obtained. As the cross-sectional area of the smoke damper increases, the extraction flow rate is concentrated in the damper close to the extraction fan, and the smoke extraction rate of the damper in downstream decreases, thereby increasing the smoke propagation distance on the downstream side. In order to prevent such a phenomenon, it is necessary to reduce the cross-sectional area of the smoke damper and increase the velocity of passing air through the damper so that the pressure loss passing through the damper increases, thereby reducing the non-uniformity of smoke extraction flow rate in the extraction section. In this analysis, it was found that when the interval distance of the extraction damper was 50 m, the air velocity passing through damper was 4.4 m/s or more, and when the interval distance of the extraction dampers was 100 m, the air velocity passing through damper was greater than 4.84 m/s, it was found to be advantageous to ensure smoke extraction performance.