• Journal of the Korea institute for structural maintenance and inspection
• /
• v.17 no.2
• /
• pp.62-70
• /
• 2013

The purpose of this study is the displacement and velocity dependence evaluation of clamped shape metallic damper, which were evaluated superior in energy dissipation capacity than straight type slit damper. For this purpose, 6 metallic damper specimens are prepared and dependence test are performed. Test variables are displacement dependence and velocity dependence. According to displacement dependence test results, larger target displacement (50mm) shows lower cyclic numbers and cumulated energy dissipated area than lower target displacement (25mm). Also it shows higher strength and early failure than short target displacement. In velocity dependence evaluation, fast target velocity (60mm/sec) shows lower cyclic numbers and cumulated energy dissipated area than slow target velocity (40mm/sec). Therefore the hysteresis dependence of metallic damper were evaluated as close relation to the loading displacement and velocity conditions.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.5
• /
• pp.976-983
• /
• 1988

An efficient unbalance response analysis method for rotor-bearing systems with spin speed dependent parameters is developed by utilizing a generalized modal analysis scheme. The spin speed dependent eigenvalue problem of the original system is transformed into the spin speed independent eigenvalue problem by introducing a lambda matrix, assuming the bearing dynamic coefficients are well approximated by polynomial functions of spin speed. This method features that it requires far less computational effort in unbalance response calculations and that the influence coefficients are readily available. In addition, the critical speeds and the corresponding logarithmic decrements can be readily identified from the resulting eigenvalues.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.18 no.5
• /
• pp.78-86
• /
• 2014

The purpose of this study is the displacement and velocity dependence evaluation of I type and S type metallic dampers. For this purpose, 12 metallic damper specimens are prepared and dependence test are performed. Test variables are strut type, displacement and velocity dependence. From the evaluation results of dependence tests, number of cycles are fully exceeded than minimum 5 cycles described in ASCE 7-10. According to displacement dependence test results, larger target displacement (50mm) shows lower cyclic numbers and cumulated energy dissipated area than lower target displacement (25mm). Also it show higher strength and early failure than short target displacement. In velocity dependence evaluation, fast target velocity (60mm/sec) shows lower cyclic numbers and cumulated energy dissipated area than target velocity (40mm/sec). As a results of basic properties, dependence evaluation and cumulated energy dissipated area evaluation, dependence capacity of S type metallic damper is far superior than I type.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.35 no.4
• /
• pp.769-777
• /
• 2015

In this study, the rheological models were introduced and developed to reflect rate dependent tensile behaviour of concrete. In general, mechanical properties(e.g. strength, elasticity, and fracture energy) of concrete are increased under high loading rates. The strength of concrete shows high rate dependency among its mechanical properties, and the tensile strength has higher rate dependency than the compressional strength. To simulate the rate dependency of concrete, original spring set of RBSN(Rigid-Body- Spring-Network) model was adjusted with viscous and friction units(e.g. dashpot and Coulomb friction component). Three types of models( 1) visco-elastic, 2) visco-plastic, and 3) visco-elasto- plastic damage models) are considered, and the constitutive relationships for the models are derived. For validation purpose, direct tensile test were simulated, and characteristics of the three different rheological models were compared with experimental stress-strain responses. Simulation result of the developed visco-elasto-plastic damage(VEPD) model demonstrated well describing and fitting with experimental results.

• The Korean Journal of Rheology
• /
• v.6 no.1
• /
• pp.49-59
• /
• 1994

높은 전기장 하에서 다분산, 비구형 실리카/실리콘 오일 현탁액의 전기유변 (electrorheological, ER)현상을 살펴 보았다. 전기유변유체는 전기장 방향으로 사슬구조를 형 성하는 특성을 보이며 이것이 유변물성의 향상에 기여하는 것으로 알려졌다. 동적(dynamic) 상태 실험에서 전기장 하의 실리카 현탁액은 매우낮은 임계변형율(${\gamma}$c =0.1%)이상에서 비선 형 점탄성을 보였다. 저장탄성계수(G＇)는 변형율 변화에 손실탄성계수(G＂)는 매질의 점도 에 더 민감한 의존성을 보였다. 또한 겉보기 항복응력은 입자의 부피분율과 전기장에$\Phi$1.9E1.4 의 의존성을 보였는데 부피분율에 대한 의존성이 큰 이유는 0.1 이상의 부피분율에서 복합 사슬 구조 내의 입자들 간의 상호 정전효과가 지배적으로 나타나기 때문이라고 생각된다. 정상상태 실험에서는 부피분율이 크거나 높은 전기장 하에서 전단속도가 0.1sec-1 정도 이하 로 감소함에 따라 전단응력이 급겨히 증가하는 현상을 보였다. 그러므로 본질적인 동적 항 복응력을 얻기 위해서는 매우 낮은 전단속도 영역의 특이한 응력거동을 고려해야한다. 큰 전단속도 하에서는 hydrodynamic interaction의 영향으로 전단속도의 증가에 따라 전단응력 이 증가하였다. 이같은 전단응력의 거동을 계단전단실험으로 확인하였다.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.10 no.4
• /
• pp.337-343
• /
• 2000

Prism plane slip {11$\bar{2}$0}1/3{$\bar{1}$120} location velocity in sapphire ($\alpha$-Al$_2$O$_3$) single crystals was measured by etch-pit method. The dislocation velocities were measured as a function of temperature and stress between $1150^{\circ}C$ and $1400^{\circ}C$ for engineering stresses in the range 140 to 250 MPa. The dependence of temperature and stress in dislocation velocity was investigated. The activation energy for dislocation velocity was determined to be 4.2$\pm$0.4 eV. On the other hand, the stress exponent (m) describing the stress dependence of dislocation velocities was in the range of 4.5$\pm$0.8. Through this experiments, it was reconfirmed that the basal plane in sapphire single crystals has the 3-fold symmetry.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.4A
• /
• pp.529-536
• /
• 2008

The failure behavior of structures is changed under different loading rates, which might arise from the rate dependency of materials. This phenomenon has been focused in the engineering fields. However, the failure mechanism is not fully understood yet, so that it is hard to be implemented in numerical simulations. In this study, the numerical experiments to a brittle material are simulated by the Molecular Dynamics (MD) for understanding the rate dependent failure behavior. The material specimen with a notch is modeled for the compact tension test simulation. Lennard-Jones potential is used to describe the properties of a brittle material. Several dynamic failure features under 6 different loading rates are achieved from the numerical experiments, where remarkable characteristics such as crack roughness, crack recession/arrest, and crack branching are observed during the crack propagation. These observations are interpreted by the energy inflow-consumption rates. This study will provides insight about the dynamic failure mechanism under different loading rates. In addition, the applicability of the MD to the macroscopic mechanics is estimated by simulating the previous experimental research.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.25 no.3
• /
• pp.189-196
• /
• 1992

To know the extension effect of storage temperature on the pre-rigor period of plaice, Paratichthys olivaceus muscle, the relationship between early changes after death and temperature dependency was studied. Killed plaices instantly with spiking at the brain were stored at $-3^{\circ}C,\;0^{\circ}C,\;5^{\circ}C\;and\;10^{\circ}$ used in studying the changes in rigor Index, ATP and its related compounds, lactate contents and K-value. The most shortest onset time of rigor-mortis and full rigor was revealed in the sample stored at $-3^{\circ}C$ among the all samples, where rigor-mortis began at 4hrs after spiking and maximum tension was attained after 28hrs. However, in case of fresh plaice muscle stored at $10^{\circ}C$, the onset of rigor-mortis and full rigor were retarded to 14hrs and 52hrs after spiking. ATP in sample stored at $5^{\circ}C\;and\;10^{\circ}C$ were decomposed slowly than sample at $0^{\circ}C\;-3^{\circ}C $ and within 35hrs storage. The fastest rate and the maximum content of lactate accumulation were showed in sample stored at $-3^{\circ}$ among the all samples. The correlation coefficient(r) between the rate of rigor mortis and ATP breakdown, rigor mortis and lactate accumulation, and ATP breakdown and lactate accumulation were -0.981946, 0.965044, and -0.964728, respectively. Freshness of $-3^{\circ}C$ stored samples was maintained for the longest time compared with other stored samples. The times reached around $20\%$ of K-value were 240hrs for samples stored at $-3^{\circ}C,\;96hrs\;for\;0^{\circ}C\;samples,\;71hrs\;for\;5^{\circ}C\;samples,\;and\;22hrs\;for\;10^{\circ}C$ samples. Samples stored at $-3^{\circ}C,\;and\;0^{\circ}C$ were showed higher temperature dependency on rate of rigor-mortis, ATP breakdown, and lactate accumulation than $5^{\circ}C\;and\;10^{\circ}C$ stored samples, but those samples have a lower temperature dependency on K-value.

• Korean Journal of Materials Research
• /
• v.11 no.3
• /
• pp.221-226
• /
• 2001

The basal slip (0001)1/3<1120 > dislocation velocity in sapphire ($\alpha$-$Al_2$$O_3$) single crystals was measured by four-point bending test. The bending experiment was carried out in the temperature range from 120$0^{\circ}C$ to $1400^{\circ}C$ at various engineering stresses 90MPa, 120MPa, and 150MPa. The velocity of such dislocations was estimated from the bending displacement rate of the four-point bend sample. The dependence of temperature and stress in dislocation velocity was investigated. The activation energy for dislocation velocity was determined to be about 2.2$\pm$0.4eV. In addition, the stress exponent (m) describing the stress dependence of dislocation velocities was in the range of 2.0$\pm$0.2.

• Korean Journal of Food Science and Technology
• /
• v.35 no.1
• /
• pp.155-158
• /
• 2003

Time-dependent flow properties of mustard pastes were measured at various total solid contents $(TS,\;18{\sim}30%)$ and shear rates $(15{\sim}25\;s^{-1})$ using a Haake concentric cylinderical viscometer. Experimental data of the stress decay with time of shearing were fitted to three mathematical models proposed by Weltman, Figoni and Shoemaker, and Hahn. Time-dependent flow behaviour of mustard paste increased with increase in TS, but was found to vary in the range of shear rate investigated. Time-dependent model of Weltman was found to be most applicable $(average\;R^2=0.96)$ for mustard paste. Shear stresses for structure breakdown increased with increase in TS, while the structure breakdown rate decreased.