• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.05a
• /
• pp.354-358
• /
• 2009

Micro gas turbine engine is well known as a power plant of unmanned aerial vehicle and a small scale emergency generation system and also, it is significant as initial research of large gas turbine and educational purpose of gas turbine. Many sort of Micro gas turbine test set for education is produced by several manufacturers, but all of the engine control system of them is separated with data acquisition system; moreover, the engine control algorithms are inaccessible and related variables could not be collected. In this investigation, the Integrated Modifiable Test Rig which has modifiable engine start-up, drive and situational control logics is developed by LabVIEW with I/O devices and it provides wide experimental applicability to studies of dynamic characteristics of fuel system and combustion instability.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.1
• /
• pp.99-104
• /
• 2009

In this paper, the drop characteristic of the small aircraft landing gear of SUAV has been analyzed and performed on orifice optimal design for shock absorption efficiency. The SUAV landing gear was simple oleo pneumatic type without metering pin. The landing gear was modelled by MSC ADAMS software. Drop test evaluation was conducted to confirm the analysis model. As a result of correlation between analysis and test results, it was verified that these results were coincided with very well. After confidence review of analysis model through the correlation between test and analysis results, design parametric study was performed by using confirmed analysis model. Optimal orifice size with best efficiency have been decided in this study.

• The Journal of Korea Robotics Society
• /
• v.9 no.3
• /
• pp.154-159
• /
• 2014

The Global Positioning System (GPS) is widely used to aid the navigation of aerial vehicles. However, the GPS cannot be used indoors, so alternative navigation methods are needed to be developed for micro aerial vehicles (MAVs) flying in GPS-denied environments. In this paper, a real-time three-dimensional (3-D) indoor navigation system and closed-loop control of a quad-rotor aerial vehicle equipped with an inertial measurement unit (IMU) and a low-cost light detection and ranging (LIDAR) is presented. In order to estimate the pose of the vehicle equipped with the two-dimensional LIDAR, an octree-based grid map and Monte-Carlo Localization (MCL) are adopted. The navigation results using the MCL are then evaluated by making a comparison with a motion capture system. Finally, the results are used for closed-loop control in order to validate its positioning accuracy during procedures for stable hovering and waypoint-following.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.40 no.6
• /
• pp.467-474
• /
• 2012

UAVs for reconnaissance and intelligence operations require long endurance capability, which demands high efficiency of the propulsion system. The distributed propulsion system(DPS) generates the thrust by replacing a large propulsion system with a number of small propulsion systems. A DPS distributed along the wing span can produce gains in propulsion efficiency by reducing ejection velocity. Also, the ingestion of boundary layers through the distributed DPS inlet and ejecting flow from the outlet can improve the lift to drag ratio of the vehicle. This study investigates the effects of locations and size of the inlet and outlet of the DPS on the blended-wing-body design based on Eppler 337 airfoil, with a CFD tool. The fans in the DPS are modeled as actuator disks for computational efficiency. The best location and aspect ratio of the inlet and outlet are found from lift-to-drag ratio and pitching moment considerations.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.39 no.10
• /
• pp.979-986
• /
• 2011

In this paper, an embedded program of a flight control system for a small high performance UAV is introduced. The program consists of modules for device management and guidance and control. The device management system handles navigation sensors and mission equipments. The program for the guidance and control system is used to accomplish various kinds of missions and realize automation of flight control. Driver programs embedded in the device management system for operation of sensors and external devices are based on Texas Instrument's DSP/BIOS RTOS(realtime operating system). The on-board programs for the guidance and control system is obtained by using the model-based auto code generation technology.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.5
• /
• pp.513-520
• /
• 2014

An unmanned aerial vehicle (UAV) should be designed to be as small and lightweight as possible to optimize the efficiency of changing the blade shape to enhance the aerodynamic performance, such as the thrust and power. In this study, a computational fluid dynamics (CFD) simulation of an unmanned multi-rotor aerial vehicle in hover mode was performed to explore the thrust performance in terms of the blade rotational speed and blade shape parameters (i.e., taper ratio and twist angle). The commercial ADINA-CFD program was used to generate the CFD data, and the results were compared with those obtained from blade element theory (BET). The results showed that changes in the blade shape clearly affect the aerodynamic thrust of a UAV rotor blade.

• Journal of Advanced Navigation Technology
• /
• v.21 no.5
• /
• pp.466-471
• /
• 2017

SOTM is a device for the satellite communication on the move. Many studies are conducted on microstrip, waveguide and array antenna for the low profile of the SOTM's antenna. But those antennas have a problem that is difficult to adjust the polarization, and for that reason we have studied the parabolic antenna structure. The general form of parabolic reflector structure is circular, but we used cut-off shape reflector by cutting the upper and lower reflector for low profile antenna. Accordingly, this results in the decrease of reflector area which causes reduced gain and G/T ratio. In order to solve this problem, we have transformed and designed the sub reflector for improving the efficiency and gain of the cut- off shape parabolic antenna.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.9
• /
• pp.854-864
• /
• 2016

The use of small drone platform has become a popular topic in these days but its application for SAR operation has been little known due to the burden of the payload implementation. Drone platforms are distinguished from the conventional UAV system by the increased vulnerability to the turbulences, control-errors and poor motion stability. Consequently, sophisticated motion compensation may be required to guarantee the successful acquisition of high quality SAR imagery. Extremely limited power and mass budgets may prevent the use of additional hardwares for motion compensation and the difficulty of SAR focusing is further aggravated. In this paper, we have carried out a feasibility study of mico-SAR drone operation. We present the image acquisition results from the preliminary flight tests and a quality assessment is followed on the experimental SAR images. The in-flight motion errors derived from the unique drone movements are investigated and attempts have been made to compensate for the geometrical and phase errors caused by motions against the nominal trajectory. Finally, the successful operation of drone SAR system is validated through the focussed SAR images taken over test sites.

• Journal of Aerospace System Engineering
• /
• v.17 no.6
• /
• pp.16-26
• /
• 2023

With the growing demand for unmanned aerial vehicles (UAVs), various collision avoidance methods have been proposed, mainly using LiDAR and stereo cameras. However, it is difficult to apply these sensors to small UAVs due to heavy weight or lack of space. The recently proposed methods use a combination of object recognition models and distance sensors, but they lack information on the obstacle size. This disadvantage makes distance determination and obstacle coordination complicated in an early-stage collision avoidance. We propose a method for estimating obstacle sizes using a monocular camera-YOLO and infrared sensor. Our experimental results confirmed that the accuracy was 86.39% within the distance of 40 cm. In addition, the proposed method was applied to a small UAV to confirm whether it was possible to avoid obstacle collisions.

• Journal of Advanced Navigation Technology
• /
• v.18 no.2
• /
• pp.107-113
• /
• 2014

In this paper, controller Propose to prevent compressor surge and improve the transient response of the fuel flow control system of turbojet engine. Turbojet engine controller is designed by applying Artificial Neural Network PID control algorithm and make an inference by applying Artificial Neural Network Error Back Propagation Algorithm. To prevent any surge or a flame out event during the engine acceleration or deceleration, the ANN PID controller effectively controls the fuel flow input of the control system. ANN PID results are used as the fuel flow control inputs to prevent compressor surge and flame-out for turbo-jet engine and the controller is designed to converge to the desired speed quickly and safely. Using MATLAB to perform computer simulations verified the performance of the proposed controller. Response characteristics pursuant to the gain were analyzed by simulation.