• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1998.04a
• /
• pp.11-11
• /
• 1998

다목적으로 활용할 수 있는 터보축 엔진의 개발을 위한 정상상태 및 동적모사 프로그램을 개발하였다. 개발비, 개발시간, 개발위험도의 절감을 위해 가스발생기 부분은 성능이 잘 알려진 기존의 터보제트 엔진을 활용하였으며 약 3000hr 이상의 수명을 확보하기 위해 터빈재질을 교체하고, Larson-Miller 곡선을 이용하여 최대회전속도와 최대 터빈 입구온도를 각각 35000 RPM과 1140 K의 결정하였다 추가되는 동력터빈의 구성품 성능선도는 압축기 터빈 성능선도를 축척하여 사용하였다. 정상상태 성능해석에는 유량 및 일평형 방정식을 이용하였으며, 동력터빈이 각각 73%, 80%, 90%, 100% RPM일 때 가스발생기를 75%(24500 RPM)에서 100%(35000 RPM)까지 5% 간격으로 나누어 계산을 수행하였다.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.23 no.6
• /
• pp.51-58
• /
• 2019

In this study, a set of performance tests on 3D-printed combustor components were carried out to investigate the performance of 3D-printed component and its feasibility for micro gas turbine engines. The test were conducted for four different equivalence ratios under two different engine operating conditions. The measurement results show that the tested combustor had a low total pressure loss coefficient and a uniform exit temperature distribution. However, the combustion efficiency values are less than 93.5% owing to the large amount of UHC and CO, which is considerably lower than a typical gas turbine engine combustor. The performance data obtained from the tests will be used for combustor performance improvements using 3D-printing technology.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.11a
• /
• pp.325-328
• /
• 2007

In this study, intended to high flight condition test, air flow test and environmental condition test of Small-sized Gas Turbine (including auxiliary power utility - APU) improve preexisting large size test stand C-9N(SCIAM) in Russia. In the process of developing C-9N test stand, this study includes conceptual design approach. This test stand consists of environmental condition, thermostat, cooling/drying, thrust measuring system and SAR (system of automatic regulation).

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2011.06a
• /
• pp.913-914
• /
• 2011

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.11a
• /
• pp.537-541
• /
• 2009

The gas turbine engine performance is greatly relied on its component performance characteristics. Generally, acquisition of component maps is not easy for engine purchasers because it is an expensive intellectual property of gas turbine engine supplier. In the previous work, the maps were inversely generated from engine performance deck data, but this method is limited to obtain the realistic maps due to calculated performance deck data. Therefore this work proposes newly to generate more realistic compressor map from experimental performance test data. And then a realistic compressor map can be generated form those processed data using the proposed extended scaling method at each rotational speed. Evaluation can be made through comparison between performance analysis results using the performance simulation program including the generated compressor map and on-condition monitoring performance data.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.14 no.3
• /
• pp.61-68
• /
• 2010

A small high altitude test facility has been developed to investigate ignition performance of a small gas-turbine combustor under high altitude conditions. Supersonic diffusers and a heat exchanger were used to perform a low pressure and a low temperature condition, respectively. Experimental results showed that the low pressure environment could be controlled by upstream pressure of primary nozzle flow and low temperature environment by mixture ratio of cooled air and ambient air. Ignition performance tests were performed to verify the performance of the facility under simulated high altitude conditions. Conclusively, it was proven that the test facility could be used for ignition performance test of a small gas-turbine combustor under high altitude condition of approximately 6,100m.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.495-498
• /
• 2010

This test cell is developed to the institutes or laboratories research and study gas turbine engine for academic purpose with this test data to provide the fundamentals of operational mechanism and structural configuration, and further to verify thermodynamic calculation The test cell is installed to monitor and compare real-time data with reference engine model performance simulation data. using by NI DAQ(Data acquisition)device and LabVIEW program based on 80 lbf-micro turbojet engine.

• The KSFM Journal of Fluid Machinery
• /
• v.12 no.3
• /
• pp.26-30
• /
• 2009

This paper predicts the critical speeds of a 5MW industrial gas turbine by using commercial rotordynamic tool, DYNAMICS 4.3. The gas turbine is operated at 12,975 rpm on squeeze film dampers. The stiffness of the squeeze film dampers are estimated. The critical speeds of the gas turbine rotor are calculated to have a sufficient separation margin (2%) from the 1st bending mode and pass over 2 rigid body modes below 4,000 cpm. This paper discussed the coupling effects on the dynamic response of the gas turbine.

• The KSFM Journal of Fluid Machinery
• /
• v.13 no.3
• /
• pp.18-23
• /
• 2010

This paper predicts the unbalance and transient (start-up) response of a 5MW industrial gas turbine by using commercial rotordynamic tool, DYNAMICS 4.3. The gas turbine is operated at 12,975rpm on squeeze film dampers or tilting pad bearings. The stiffness and damping coefficients of the squeeze film dampers and tilting pad bearings are estimated. It is seen that the vibration amplitude of the gas turbine rotor is sufficiently small around the critical speeds and at the rated speed.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.25 no.4
• /
• pp.71-77
• /
• 2021

Several cooling techinques have been studied for protecting gas turbine blades from hot gas. In terms of film-cooling techniques, various shapes of film cooling holes have been studied including fan shaped holes, which are used on gas turbine blades. However, owing to increasing demands on smaller gas turbines, a research on film-cooling holes on thin walls is required. This study was conducted at blowing ratios of 1 and 2, using numerical analysis. Through the numerical analysis, the effect of geometrical parameters on the effectiveness of fan-shaped hole film cooling was studied. Moreover, optimization was performed on three geometrical parameters: metering length, lateral expansion angle and forward expansion angle. As a result, we realized that the optimal fan-shaped holes on each blowing ratio were found to have very similar geometry and cooling performance.