• Journal of the Korean Geotechnical Society
• /
• v.26 no.12
• /
• pp.5-17
• /
• 2010

Coarse granular material is used as important fill material in most of large embankments such as railway, road, dam and so on. Therefore, the accurate design parameters of the coarse granular material are necessarily required in design and construction. The behavior of the coarse granular material was not well understood because of the lack of large testing equipment capable of coarse granular material. A large triaxial testing system was developed in this research, capable of large specimens of 500 mm, 300 mm and 150 mm in diameter. In the new large triaxial testing system, the load cell is installed inside the triaxial cell and axial displacement is measured locally on a specimen in order to improve control and measurement in small strain level. Urethane specimens of 300 mm and 50 mm in diameter were prepared. The large triaxial tests were performed on the 300 mm diameter urethane specimens while RC/TS and impact echo tests on the 50 mm diameter urethane specimens to verify this testing system. In this verification test results, we could ascertain the reasonable test results of the KRRI large triaxial testing system.

• Journal of the Korean Society of Radiology
• /
• v.5 no.6
• /
• pp.357-361
• /
• 2011

In this study, the liquid-crystal optical modulation X-ray detection system using a CdS which is a family of II-IV compound semiconductor was proposed. The system consist of the detector, the signal processing part, the liquid-crystal driving parts, microcontroller, and I/O parts, and was designed to be suitable for miniaturization and portable. In addition, the system can measure a wide range X-ray by using the detecting range selection. In order to evaluate the performance of the proposed system, the CdS sensor's output characteristics were confirmed in accordance with changes of dose, and excellent correlation was determined. And also, the optical penetration ratio was discussed in accordance with changes of the applied voltage by measuring the change of the liquid-crystal in accordance with changes of the applied voltage. Through these results, the characteristics of the liquid-crystal optical modulation system such as the excellent reproducibility and the noise immunity were confirmed. And we considered that the CdS cell-based liquid-crystal optical modulated portable X-ray detection system could be applied to compact, low-cost, portable system.

• 전자공학회논문지 IE
• /
• v.49 no.1
• /
• pp.18-23
• /
• 2012

In this paper, a potable device application for DC-DC converter was designed for voltage protection circuit. Voltage protection circuit to offer the under voltage lock out and over voltage protection consists of a comparator and bais circuits were implemented using. XFAB 1um CMOS process, SPICE simulations was confirmed through the characteristics. Simulation results, under voltage lock out input voltage is 4.8 V higher when the turn-on and, 4.2 V less when turn-off. When the input voltage is low voltage is applied can be used to prevent malfunction of the circuit. Over voltage protection is 3.8 V reference voltage when the output voltage caused by blocking circuit prevents device destruction can be used to improve the stability and reliability. The virtual control circuits of the DC-DC converter connected. According to the results of the abnormal voltage, voltage protection circuit behavior was confirmed. The proposed voltage protection circuit of the DC-DC converter cell is useful are considered.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.1
• /
• pp.45-51
• /
• 2015

In this paper, we study the RF characteristics of the short wavelength thin-film transmission line employing microstrip line (ML)/coplanar waveguide (CPW) composite structure on silicon substrate for application to RFIC (radio frequency integrated circuit). The thin-film transmission line employing ML/CPW composite structure showed a wavelength shorter than conventional transmission lines. Concretely, at 10 GHz, the wavelength of the transmission line employing ML/CPW composite structure was 6.26 mm, which was 60.5 % of the conventional coplanar waveguide. We also extracted the bandwidth characteristic of the transmission line employing ML/CPW composite structure using equivalent circuit analysis. The S parameter of the equivalent circuit showed a good agreement with measured result. According to the bandwidth extraction result, the cut-off frequency of thin-film transmission line employing ML/CPW composite structure was 377 GHz. Above results indicate that the transmission line employing ML/CPW composite structure can be effectively used for application to broadband and compact RFIC.

• Journal of Advanced Navigation Technology
• /
• v.19 no.1
• /
• pp.60-65
• /
• 2015

In the present study, compact $0^{th}$ order resonant antenna for 2.4 GHz ISM frequency band is newly proposed. In case of wireless communication systems such as wi-fi, bluetooth and Zigbee, antennas with omni-directional radiation pattern are necessary because of the demands for uniformly received electric field strength without variation for direction. It is well-known that $0^{th}$ order resonant antennas are not only advantageous for miniaturization but also have advantage of maintaining omni-directional radiation pattern. The proposed antenna is composed of two-element array in which the size of unit element should be smaller than ${\lambda}/4$ correspondent to the resonant length of typical monopole antennas The proposed antenna which is placed at middle and upper side of PCB with $50{\times}50mm^2$ size is designed and fabricated within limited space of $8{\times}5mm^2$. The measured impedance bandwidth ($S_{11}{\leq}-10dB$) is about 100 MHz (2.4~2.5 GHz) which corresponds to quite wide bandwidth in comparison with the antenna size, and also the measured peak gain over the passband is more than 3 dBi which is thought to be slightly wider than the other $0^{th}$ order resonant antenna.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.35S no.11
• /
• pp.19-27
• /
• 1998

To achieve the required services in the next-generation cellular telephone systems, the size of the cell become smaller and/or is of mixed macrocells and microcells. For more efficient system control, We make use of the mobile position and velocity information, provided that the mobility information is relatively accurate. In this paper, we propose an improved version of path-loss measurement algorithm introduced in literature[11]. The microcellular structure with severe multipath fading, reflection and refraction make mobile position and velocity estimation very difficult. In the proposed method, the pre-recorded path-loss informations, called the discrete position data base, are searched to estimate the position. Velocity estimation is obtained as a difference of the position values with respect to the time difference. Moving average filter is applied to smooth the estimated velocity and to reduce the error in the estimates. We also propose a method to simplify system implementation by reducing search area for discrete area database.

• The Journal of the Korea Contents Association
• /
• v.7 no.2
• /
• pp.92-99
• /
• 2007

This paper presented a low power design of a 32bit block cypher processor reduced from the original 128bit architecture. The primary purpose of this research is to evaluate physical implementation results rather than theoretical aspects. The data path and diffusion function of the processor were reduced to accommodate the smaller hardware size. As a running example demonstrating the design approach, we employed a modified ARIA algorithm having four S-boxes. The proposed 32bit ARIA processor comprises 13,893 gates which is 68.25% smaller than the original 128bit structure. The design was synthesized and verified based on the standard cell library of the MagnaChip's 0.35um CMOS Process. A transistor level power simulation shows that the power consumption of the proposed processor reduced to 61.4mW, which is 9.7% of the original 128bit design. The low power design of the block cypher Processor would be essential for improving security of battery-less wireless sensor networks or RFID.

• Journal of Advanced Navigation Technology
• /
• v.15 no.6
• /
• pp.1104-1110
• /
• 2011

The conventional semiconductor equipment has adopted SRAM module as the test pattern memory, which has a simple design and does not require refreshing. However, SRAM has its disadvantages as it takes up more space as its capacity becomes larger, making it difficult to meet the requirements of large memories and compact size. if DRAM is adopted as the semiconductor inspection equipment, it takes up less space and costs less than SRAM. However, DRAM is also disadvantageous because it requires the memory cell refresh, which is not suitable for the semiconductor examination equipments that require correct timing. Therefore, In this paper, we will proposed an algorithm for punctuality guarantee of memory-free inspection equipment using DDR2 SDRAM. And we will Developed memory controller using punctuality guarantee algorithm. As the results, show that when we adopt the DDR2 SDRAM, we can get the benefits of saving 13.5 times and 5.3 times in cost and space, respectively, compared to the SRAM.

• Korean Chemical Engineering Research
• /
• v.58 no.4
• /
• pp.536-540
• /
• 2020

The support of the PEMFC membrane plays a key role in improving mechanical durability. The e-PTFE used as a support is chemically stable, so electro-chemical degradation in the PEMFC driving process has been rarely studied. In this study, we investigated whether e-PTFE is chemically stable to radicals and hydrogen peroxide during Fenton reaction. After the Fenton reaction, the main chain of e-PTFE broke, resulting in a change in the chemical structure and morphology of the support, resulting in a decrease in tensile strength. The results of this study showed that electrochemical degradation of the membrane ionomer in the PEMFC process occurs inside the membrane by radicals and hydrogen peroxide, so that electrochemical degradation may also occur at the e-PTFE support in the cell.

• Korean Chemical Engineering Research
• /
• v.56 no.3
• /
• pp.315-319
• /
• 2018

Fenton reaction is widely used as a out of cell method for evaluating the membrane electrochemical durability of Proton Exchange Fuel Cell (PEMFC). In this study, we investigated the factors affecting the Fenton reaction. In order to estimate the degree of the reaction, it is necessary to analyze the radicals as a product in the Fenton reaction. However, since the radicals are difficult to analyze, the degree of the reaction was measured by analyzing the concentration of hydrogen peroxide. The activation energy was calculated from the rate of hydrogen peroxide change with temperature. The activation energy was 24.9 kJ/mol at 180 min. The Fenton reaction rate was affected by the iron ion concentration. At $80^{\circ}C$, 200 rpm, and $Fe^{2+}$ 80 ppm, the concentration of hydrogen peroxide was decreased more than 20% even for 1 hour, which shows that frequent solution replacement increases the membrane degradation rate.