• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2012.05a
• /
• pp.378-379
• /
• 2012

Nowadays, great energy consumption in advanced electrical industry has called up the great y efficiency. Electric power IT industry such as intelligent electric power system is receiving great attention and being marked up as a new growth engine. Through Intelligent electric power system, the electric power supply can be balance optimized according to demand, giving huge cost savings advantage for energy imports, infrastructure construction and operation. Nevertheless, the intelligent system promotes better reliability in power supply. Manual electric power management using man power appears to be non-practical. Real time electric power management on all facilities and equipment can be done through an intelligent electric power system, any accident break out issue can be easily recorded and recognized. In this paper, a fully integrated intelligent switchgear electric management system is developed to monitor and remote control the electrical switch based on smart phone. The proposed system is superior than the existing switchgear management system's weakness and can sharply improve effectiveness and stability with low cost. In future, the proposed system is expected to be greatly contributed to the advancement of the IT industry in electric power management.

• Applied Chemistry for Engineering
• /
• v.2 no.3
• /
• pp.209-215
• /
• 1991

The effect of agitation on the dispersion of organic phase was investigated in an immiscible liquid system (n-hexane/40 wt % p-TSA aqueous solution). Four different types of six-bladed turbine impellers were used : a flat blade type and three screen blade types. The experimental results showed that the extent of dispersion of organic phase at the same agitation speed was decreased in the order of flat blade, 60 mesh, 40 mesh, and 20 mesh screen blades. Otherwise, it was increased with increasing the concentration of TBA as a surfactant agent and with decreasing volume fraction of organic phase. Also, the minimum agitation speed for a complete dispersion was increased in the order of flat blade, 60 mesh, 40 mesh, and 20 mesh screen blades. However, the minimum power consumption did not vary significantly. In this condition, the relationship between Power number and Reynolds number was expressed as $N_p=a\;N_{Re}{^b}$, where the values of constant a and constant b were ranged 2200~4100 and -0.69~-0.63 respectively.

• The Journal of the Korea Contents Association
• /
• v.17 no.6
• /
• pp.272-286
• /
• 2017

The division of the South and North of 70 years has occurred in the old generation, but the reunification is now handled by the youth generation. Therefore, it is necessary to train basic human nature as well as learning and research of rational political and economic theory in order for young adolescents as leaders in the unification era to carry out their own duties faithfully and responsibly. In this paper, I rediscover the value of traditional culture in the human nature education that aims for reunification, social and cultural integration, and propose tea culture as contents that can be applied to reunification and the human nature education of youth as reunification culture contents as a concrete program of traditional culture do.

• Journal of Biosystems Engineering
• /
• v.4 no.2
• /
• pp.46-52
• /
• 1979

The water delivery hose for agricultural pump is getting popular in rural areas in korea. Friction head loss, discharge, and power requirements were measured in various discharge for different material and diameter of hose to get basic data for economical use in agricultural pump. The results attained in this study were as follows ; 1. Friction head loss increased significantly as the velocity increased, and the difference of velocity between the different diameter of hose was bigger than that between materials, which was resulted in the increase of the friction head loss. 2. Friction head loss in the case of that the velocity with 2m/sec was constant was about 3.53 to 4.01 m/100m in the diameter 3" and about 2.30 to 3.10 m/100m in the diameter 4". Material A of diameter 3" showed the maximum value 8.4m/100m in Reynolds number $2.0\times10^5$, 4" got the minimum value 2.24m/100m, the difference between these values was bigger than 6m per 100 meters in the friction head loss. 3. Darcy-Weisbach formular with friction coefficient [f] calculated by Nikurades formular in the smooth pipe or with friction coefficient [f] calculated on the base of C value 125 in Hazen-Williams formular was available in friction head loss of the water discharger hose in rural areas. 4. Total head increased as friction head loss increased , meanwhile total discharge decreased, and 20 percents of energy was more saved in Material C 4″pipe than Material A 3″pipe in the view point from the discharge per unit power requirement, this phenomenon suggested that long distance pipe would be advantage in larger diameter pipe for save of energy. for save of energy.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.13 no.4
• /
• pp.119-125
• /
• 2007

In recent days, the consumption of stainless steel in the propulsion shafting systems for small-medium class vessel is increased due to its high corrosion protection with wear resistant properties. Unfortunately the small and medium class vessel that operated in the west-south sea area of Korean peninsula experienced heavy wear down due to the role of mud. In the event of wear or broken down, the propeller shaft must be replaced by new one, but the new shaft is very expensive and time-consuming for order made supply. In this case, the methods of built up for wear and broken shaft by welding is one of the most effective cases. In this study, the built up welding for austenitic stainless steel shaft has been accomplished by various pre-surface treatment, welding methods, post heattreatment and inspection. The results confirmed that the built-up welding was one of the effective methods for stainless steel shafting.

• Journal of Biosystems Engineering
• /
• v.6 no.1
• /
• pp.1-14
• /
• 1981

A laboratory model test was carried out with a newly designed model to figure out the vibration characteristics of the vibratory tillage tool according to the method of forced vibration, i.e., horizontally and vertically forced vibrations. The results are summarized as follows: 1. The reduction ratios of the draft force of the vibratory blade were 14.2-42.6% for the case where the vibration was forced parallel to the travelling direction of the blade, and 15-54.5% for the vertically forced vibration. And it was thought that the method of vertically forced vibration was preferable to the reduction of the draft force. 2. The ratio of the draft force of a vibratory blade to that of a static one could be represented as a function of V/At. It was found to be possible to reduce the draft force by taking a lower value of (V/Af) and this meant that the effictiveness of tillage practice using the vibratory system would be limited. 3. The torque to the main rotating shaft to vibrate the model blade increased frequency and amplitude. This tendency varied according to the physical properties of tested soil. In case of horizontally forced vibration, the torque was 8~34% less than in case of vertically forced vibration. 4. With the increase of frequency, the total power requirement increased linearly, and also the portion of oscillating power requirement in the total power tended to increase. The magnitude of the total power requirement was 1.4-13 times greater than that of a static one for the case of horizontal vibration, and 1.5-15 times greater for the case of vertical vibration. It was thought that the horizontal vibration of the blade was preferable to the vertical vibration in view of the power requirement. 5. A linearity was found between the amplitude of moment oscillogram and magnitude of oscillating acceleration. Only positive values of moment occurred when the blade was forced to vibrate vertically, but negative values occurred in rarity in the case of amplitude A3 when the blade was forced to vibrate horizontally.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.6
• /
• pp.599-605
• /
• 2013

The characteristics of centrifugal pump performance according to fluid viscosity change were studied experimentally. A small volute pump with low specific speed was tested by changing the viscosity of an aqueous solution of sugar and glycerin, which is considered a Newtonian fluid. After finishing the test, the total head, shaft horsepower, and pump efficiency were compared with those of a water pump. The results are summarized as follows: (1) when the fluid viscosity is increased, the shut-off head shows very little change but the total head decreases gradually as the flow increases, and this makes the H-Q curve leaning rapidly, and (2) when the fluid viscosity is increased, the shaft horsepower shows very little change at the shutoff condition; however, the shaft horsepower increases more rapidly with an increase in the flow and viscosity.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.41 no.1
• /
• pp.115-122
• /
• 1996

One of the most laborious work in rice farming is transplanting of rice seedling which has been required preparation of nursery bed and care of seedling during one month period. In this research, direct seeding in dry paddy(DS) and direct seeding in wet paddy(WS) were practiced to compare with traditional transplanting(TP) in Suwon. Growth stages in direct seeding were delayed as its planting time was about 21 days later than those of TP. Heading stage of direct seeding at Suwon was delayed about 9 days as compared to transplanting culture. Rice yield was not different between the seeding practises. Working-hour saving was about 17％(DS) and 28％(WS). Production cost of direct seeding was decreased 20％(DS) and 32％(WS), respectively. Amount of rice production per a unit working-hour in direct seeding could increase 14％(DS) and 39％(WS) compared to that of TP, respectively. Therefore, direct seeding could save significantly working hour and production cost without reducing rice yield. WS was more effective than DS in saving labor and production cost. Direct seeding was not efficient method in input of farming energy and agricultural chemicals.

• Journal of Animal Environmental Science
• /
• v.15 no.1
• /
• pp.29-36
• /
• 2009

The authors of this study have developed a robot milking system composed of a multi-articular manipulator, a teat-cup attachment system, and an image processing system. In order to verify the efficacy of this system, we have conducted a performance analysis and measurement experiment of milk yield, using dairy cattle. It was concluded that teat recognition using the image processing system, teat-cup attachment, and detachment system did not binder milking. The milking yield of the robot milking system was analyzed based on a lactation curve. As a result, it was determined that the use of a robot milking system had no significant effects on milking yields. The robot milking system described in this study is designed specifically with a focus on teat-cup attachment and detachment performance, as well as the effect of these factors on milking yield. In the future, in-depth studies regarding the washing of the teats prior to milking, teat massage, pre-treatment and post-treatment processes after milking, and disinfection processes shall be conducted, in order to render this system feasible for use in an actual milking parlor.

• Journal of Biosystems Engineering
• /
• v.13 no.2
• /
• pp.18-27
• /
• 1988

The basic model of impeller was developed for the theoretical analysis of performance. The developed model was tested with two different blade radius of curvature based on the pumping efficiency under the operating conditions in Korea. And the pump performance of the impeller was also tested for the various speeds. The results obtained are summarized as follows; 1. There was no significant effect on the different blade radius of curvatures on the discharge and pump efficiency. 2. Head and power requirement was increased in proportion to the blade radius of curvature. 3. In the mathematical approach of the blade radius of curvature, the method of involute curve was more recommendable as compared with the method of circular arc curve. 4. The pump efficiency of the model impeller developed based on the theoretical analysis increased about 10% more than that of the existing impeller.