• Journal of the Korea Concrete Institute
• /
• v.27 no.1
• /
• pp.65-73
• /
• 2015

This study discussed the pozzolanic properties of calcined sewage sludge (CSS) according to calcination and fineness conditions. The chemical and mineralogical analysis of CSS according to calcination temperature and time were carried out and compared with that of the existing pozzolanic materials such as fly-ash, blast furnance slag and meta-kaolin. Various mortars were made by mixing those CSS and $Ca(OH)_2$ (1:1 wt. %), and their compressive strength and hydrates according to experimental factors such as fineness of CSS and curing age were also investigated in detail. The results show clearly the potentiality of calcined sewage sludge (CSS) as an admixture materials in concrete, but the CSS should be controlled by calcination temperature and time, and fineness etc. In this experimental condition, the calcination temperature of $800^{\circ}C$, calcination time of 2 hours and fineness of $5,000cm^2/g$ were optimum conditions in consideration of the mechanical properties and economic efficiency of CSS. The compressive strength of CSS mortars was higher than that of fly-ash mortars and blast furnace slag mortars, especially at the early ages. Then, the utilization of CSS in construction fields was greatly expected.

• Journal of the Korean Magnetics Society
• /
• v.10 no.5
• /
• pp.225-231
• /
• 2000

The crystallographic and magnetic properties of the sample F $e_{0.8}$ $Co_{0.18}$(BN)$_{0.02}$ synthesized by microwave arc-melting with the maximum power of 3.5 kW have been studied by the methods of an X-ray diffraction and the measurement of the magnetic hysteresis using the vibrating sample magnetometer at room temperature. The samples were prepared in a form of pellet pressed under the pressure of 9,000 N/c $m^2$, rolled coldly, and treated with the different temperatures. The X-ray diffraction pattern of pelleted sample shows that the crystal structure of the sample is bcc as same as that of Fe with a good uniformity. The X-ray diffraction pattern shows that a residual stress, which exists in the sample, is eliminated by final 90$0^{\circ}C$ annealing. As rolling rate and heat treatment temperature increases, the saturation magnetization and the remanence of the samples increase whereas the coercivity of the samples shows decrease. Also the saturation magnetization and the remanence of the samples were affected by rolling rate and rolling direction than heat treatment temperature, but the coercivity of the samples was affected by rolling rate and direction as well as heat treatment temperature. This means that a domain wall motion is easy due to elimination of a residual stress and an inclusion which exists in the sample by rolling and heat treatment and a local induced-magnetization easy axis was also formed to parallel to the rolling direction due to creation of the like-atom pairs across the slip plane by rolling......

• Economic and Environmental Geology
• /
• v.51 no.6
• /
• pp.485-492
• /
• 2018

About 300 thousand tones of oyster shells are produced annually and, thus, their massive recycling methods are required. Recently, a method, utilizing them as wet desulfurization materials after removal of organic matters and changing $CaCO_3$ phase into CaO through calcination, is under consideration. This study investigates the mineralogical changes (specific surface area, phase changes, surface state, etc.) of oyster shells by calcination and their characteristics were compared with those of limestone. Uncalcined oyster shells showed the higher specific surface area than limestone because the former are composed of platy and columnar structures. In contrast, investigated limestone showed a dense structure. The phase change of oyster shells occurred at lower temperature than that of limestone. The specific surface area of oyster shell decreased significantly after calcination while limestone depicted a drastic increase. Small amount of Na contained in oyster shell was suggested as the cause of this phenomenon; in that, it acted as a flux causing melting and sintering of oyster materials at lower temperature. Because of this, an additional phenomenon was observed that a part of shell materials remained untransformed even at higher calcination temperature and after longer treatment period due to the sintered surface, which covers the rest parts. Further studies investigating the effect of this phenomena from the perspective of desulfurization is required.

• Journal of the Korean Society for Heat Treatment
• /
• v.15 no.1
• /
• pp.9-15
• /
• 2002

Deformation behavior of nickel-rich Ti-51.5at.%Ni single crystals was investigated over a wide range of temperatures(77 to 440K) and strain levels(up to 9%) in compression. These alloys combined superior strength with wide range of pseudoelasticity temperature interval(~200K). The slip deformation in [001] orientation did not occur due to the prevailing slip system, and consequently, exhibited pseudoelastic deformation at temperatures ranging from 77 to 283K and 273 to 440K for the solutionized and over-aged cases, respectively. The critical transformation stress levels were in the range of 800 to 1800MPa for the solutionized case, and 200 to 1000MPa for the over-aged case depending on the temperature and specimen orientation. These stress levels are considerably higher compared to these class of alloys having lower Ni contents. The maximum transformation strains, measured from incremental straining experiments in compression, were lower compared to the phenomenological theory with Type II twinning. A compound twinning model depending on the successive austenite(B2) to intermediate phase(R) to martensite(B19') transformation predicts lower transformation strains compared to the Type II twinning case.

• Journal of the Korean Society for Heat Treatment
• /
• v.8 no.4
• /
• pp.266-278
• /
• 1995

The high strain-rate dynamic plastic behavior of Fe-X%Mn alloys was investigated. The strain rate did not have an effect when tested under quasi-static strain rates($2{\times}10^{-3}/sec$ and $2{\times}10^{-1}/sec$). However, the true stress increased at all strain levels when the strain rate increased to $6{\times}10^3/sec$. Based on the experimental results, an constitution equation to calculate the dynamic strength for strain rates over $10^4/sec$ was determined. The Fe-5%Mn alloy containing athermal ${\alpha}^{\prime}$ martensite initially did not show work hardening. The work hardening increased with Mn content showing a maximum at 20% Mn. The high work hardening of Fe-20%Mn and Fe-30%Mn alloys appears to be closely related not only to the initial amounts of ${\varepsilon}$ martensite but to the strain induced transformation (${\gamma}{\rightarrow}{\varepsilon}$ and ${\varepsilon}{\rightarrow}{\alpha}^{\prime}$) occurring during each stages of deformation.

• Journal of the Korean Society for Heat Treatment
• /
• v.9 no.2
• /
• pp.147-158
• /
• 1996

Generally, analytical consideration on the behaviour of metallic structures during quenching process, and analysis on the thermal stress and deformation after heat treatment are very important in presumption of crack and distorsion of quenched material. In this study a set of constitute equations relevant to the analysis of thermo elasto-viscoplastic materials with strain hysteresis during quenching process way presented on the basis of contimuum thermo-dynamics mechanics. The thermal stresses were numerically calculated by finite element technique of weighted residual method and the principle of virtual work. In the calculation process, the temperature depandency of physical and mechaniclal properties of the material in consideration. On the distribution of elasto-viscoplastic thermal stresses according to radial direction, axial and tangential stress are tensile stress(50MPa, 1.5GPa and 300MPa) in surface and compressive stress(-1.2GPa, -1.14GPa and -750MPa) in the inner part on the other hand, radial stress is tensile stress(900MPa) in area of analysis. According to axial direction, tangential stress gradients are average 60MPa/mm on the whole. The reversion of stress takes place at 11.5 to 16.8mm from the center in area of analysing.

• Journal of the Microelectronics and Packaging Society
• /
• v.3 no.2
• /
• pp.27-38
• /
• 1996

Lithium fluorhectorite 결정상을 함유한 glass ceramics 분말의 형성과 제조된 glass ceramics 분말을 이용한 저온 소결기판의 특성평가를 하였다. Li2O-MgO-MgF2-SiO2 계 유 리로 핵형성 및 결정 성장을 실시하여 lithium fluorhectorite 결정상을 지닌 glass ceramics 를 제조하였다. 유리시편의 핵형성 온도는 46$0^{\circ}C$였고 결정성장온도는 600, 640, 110$0^{\circ}C$에서 나타났다. $600^{\circ}C$에서의 결정상으 Li2.4LiSi4O10F2가 나타났다. Li2.4Mg8LiSi4와 Li2.8Mg0.6SiO4은 lithium fluorhectorite 결정상으로 되기 위한 중간상임을 확인할수 있었다. 64$0^{\circ}C$에서 열처리 후 110$0^{\circ}C$에서 재열처리하여 형성된 결정은 lithium fluorhectorite 와 tridymite가 최종 결정 상으로 나타났다. 이것은 수중에서 water swelling 현상에 의하여 분말화할 수 있었다, 기판 제조용 slurry를 제조하기 위해 glass ceramics 분말에 Al2O3분말을 0,25,50wt%로 혼합한것 과 glass ceramics 분말에 potashborosilica-te glass 분말을 15, 30, 45, 60 wt% 로 배합하 여 doctor blade 법으로 green sheet를 제조하였다. green sheet 는 950~150$0^{\circ}C$로소성하여 기판의 특성을 평가하였다. 겉보기 기공율은 3.06~19,14%이었고, 전기적 특성으로 유전상수 는 3~5(100KHz)를 나타내었다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.463-463
• /
• 2008

The glass frit has been used in transparent dielectric, barrier rib and electrode of PDP (Plasma display panel). In PDP fabrication, the firing temperature of glass frit is normally 550~$580^{\circ}C$ with conventional heating. However, there are a problem that silver in electrode is diffused throughout the transparent dielectric. For inhibiting the Ag diffusion we considered use of the microwave heating. We investigated firing of glass frit compared between conventional and microwave heating. After firing by two types of heating, the diffusion of silver is determined using a optical microscope and UV-spectrometer. Based on the our results, the microwave heating should be a candidate to heating source for high efficacy in PDP.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.10a
• /
• pp.431-434
• /
• 2008

In the present study, direct quenching of alloyed steel after hot forging was simulated using commercial finite element program, $FORGE^{TM}$. A typical heat treatment of alloyed steels consists of quenching for hard martensite and subsequent tempering for toughness. In the practice, forgings which cool down to room temperature are heated to temperature of austenite regime. As investigated in the present study, direct quenching of hot forged stock would be beneficial in terms of energy saving. This process has already been propose and termed as ausforging or forged hardening. However, it is well known that quenching temperature would be the most critical factor to control heat treated forging properties. And it is very difficult to control quenching temperature when forged stock gets directly quenched after forging. In this study, we have calculated final forging temperature of stock. Also, quenching simulation was conducted using a series of material parameter which were also calculated using JMATpro, a commercial program for physical properties of materials.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.10a
• /
• pp.138-141
• /
• 2008

The effects of annealing temperature and time on mechanical properties and microstructures were investigated in cold drawn pearlitic steel wires. During annealing, the increment of the tensile strength at low temperatures found to be due to age hardening, while the decrease in the tensile strength at high temperatures was attributed to age softening, involving the spheroidization of lamellar cementite and recovery of lamellar ferrite. Since tensile strength and the occurrence of the delamination would be closely related to the dissolution of cementite, the lower annealing temperature and the increase of drawing strain caused the higher tensile strength and the easier occurrence of the delamination in cold drawn pearlitic steel wires.