• Journal of the Earthquake Engineering Society of Korea
• /
• v.10 no.5 s.51
• /
• pp.85-97
• /
• 2006

Capacity design is to guarantee ductile failure of whole bridge system by preventing brittle failure of columns and any other structural elements until the columns develope fully enough plastic deformation capacity. This concept has been explicitly regulated in most bridge design specifications of foreign countries except the current Korea Bridge Design Specifications. In the capacity design, the transformed shear force from flexural overstrength of reinforced concrete column is used as the design lateral shear force for shear design of columns and design of footings and piles. Different calculating methods are adopted by the design specifications, since the variability of material strength and construction circumstances of the local regions should be considered. This paper proposed material overstrength factors by investigating 3,407 reinforcing bar data and 5,405 concrete compressive strength data collected in Korean construction sites. It also proposed calculating procedures for flexural overstrength of reinforced concrete columns using the material overstrength. Finally, overstrength factor was proposed as 1.5 by investigating 1,500 column section data from moment-curvature analysis using the material overstrength.

• Journal of Conservation Science
• /
• v.22
• /
• pp.15-30
• /
• 2008

The roof tiles from the tomb in Baekje Kingdom of the Danjiri site in Gongju, Korea were studied for the production techniques and raw material provenance based on archaeometric characteristics. The roof tiles had traditional shapes of Baekje Kingdom, which show flow texture on the surfaces and sections with the roof tiles of hard or soft-type. These roof tiles were locally produced, using refining soils according to mineralogical and geochemical characteristics. Also roof tiles were divided to 2 groups by firing temperature and physical properties. One of them had soft with porous texture and fired probably about 700 to $900^{\circ}C$. The other had hard with vitrified texture and probably fired about 940 to $1,020^{\circ}C$. Buried for long time and used as a tomb, roof tiles had experienced chemical alteration due to the enrichments of trace elements abundant in human tissues.

• International Journal of Highway Engineering
• /
• v.13 no.1
• /
• pp.41-48
• /
• 2011

Warm-Mix Asphalt(WMA) mixtures, which meet environmental protection and have high energy efficiency, are emerging as an alternative to hot-mix asphalt mixtures. The objective of this study is to evaluate WMA made with Aspha-min in the laboratory and to compare the design results accomplished by new Mechanistic-Empirical Pavement Design Guide(MEPDG) with control mixture. An asphalt mixture with a nominal maximum size of 12.5mm and PG64-28 binder was used. Resilient modulus tests for a control mixture and WMA with 0.3% and 0.5% of Aspha-min were conducted. The results obtained by MEPDG after inputting the test output into the design indicated that the predicted rut depth of WMA using Aspha-min was much lower than that of control mixture, and showed that WMA was more resistant to rutting than control mixture.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.5A
• /
• pp.833-840
• /
• 2006

In design of steel column member using TMCP steels, hysteretic behavior characteristics of steel column must be clarified. To predict hysteretic behavior of steel column using TMCP steels, a cyclic plasticity model is necessary which can consider the mechanical characteristics and stress-strain relationship of TMCP steels. In this paper, a cyclic plasticity model of SM490-TMC was formulated based on monotonic and cyclic loading tests. The formulated cyclic plasticity model was applied to 3-dimensional finite element analysis. Hysteretic behavior characteristics of steel circular column and H-section column using SM490-TMC was presented by carrying out numerical analysis. Also, influence of SM490-TMC on hysteretic behavior of steel column was presented by comparing analysis results both SM490 and SM490-TMC steel column.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.3A
• /
• pp.447-455
• /
• 2006

A general purpose of 4-node co-rotational resultant shell element is developed for the solution of nonlinear problems of reinforced concrete, steel and fiber-reinforced composite structures. The formulation of the geometrical stiffness presented here is defined on the mid-surface by using the second order kinematic relations and is efficient for analyzing thick plates and shells by incorporating bending moment and transverse shear resultant forces. The present element is free of shear locking behavior by using the ANS (Assumed Natural Strain) method such that the element performs very well as thin shells. Inelastic behaviour of concrete material is based on the plasticity with strain hardening and elasto-plastic fracture model. The plasticity of steel is based on Von-Mises Yield and Ivanov Yield criteria with strain hardening. The transverse shear stiffness of laminate composite is defined by an equilibrium approach instead of using the shear correction factor. The proposed formulation is computationally efficient and versitile for most civil engineering application and the test results showed good agreement.

• Journal of Conservation Science
• /
• v.25 no.1
• /
• pp.101-114
• /
• 2009

Potsherds and kilns of the AD 3th century excavated from Gundong and Majeon sites, Korea were studied to investigate the production techniques and provenance of potsherds and kilns on the pastes. For potsherds, kilns blocks and in-situ paleo-soils, provenance of raw materials were estimated through mineralogy and geochemistry, while production technique and thermal feature of kilns were investigated through observation of textures and compositions as well as firing experiment on paleo-soils. As a result of study, potsherds and kilns were found to have similar mineralogical compositions as the neighboring paleo-soils and to have same evolution path with that of geochemistry. The potsherds were divided into 3 groups according to firing temperature and production technique. Group 1 consists of reddish stamped pattern pottery with loose textures, which has many pores and contains many iron oxides. Its temper is less than about 0.5mm, and was probably fired between 700 to $800^{\circ}C$. Group 2 contains ash to grayish blue stamped pattern pottery, which has vitrified texture and few pores. Its temper is less than about 0.5mm, and was probably fired from 900 to $1,000^{\circ}C$. However, some potsherd belongs to the group 2 in terms of features for temper and pastes, but it was probably fired over $1,100^{\circ}C$. Group 3 contains reddish and grayish stamped pattern pottery. It has vitrified matrix, few pores and temper consists of polycrystalline quartz and feldspar over 2mm, and it was probably fired around $1,000^{\circ}C$. The kiln had experienced temperature from 600 to $700^{\circ}C$ on the wall, from 900 to $1,000^{\circ}C$ on the bottom, suggesting the function of high temperature firing.

• Journal of Bio-Environment Control
• /
• v.8 no.4
• /
• pp.257-264
• /
• 1999

The trickling system for automatic and individual watering were made with Bunchungto, Ongito and Backjato. The thickness of ceramics were 1.0, 1.5, 2.0, 2.5 and 3.0mm. And they were fired in a muffle furnace at five different temperatures between 500 and 900'E during 12 hours. The upper plastic parts of sensor consisted of five elements made by steel mold. With the photo fiber sensor attached to datalogger, an accumulated amount of drops for every 10 minutes were recorded. The porosity is higher in the order of Bunchungto, Backjato and Ongito; also, as the firing temperature is higher and the thickness is thicker, the porosity is higher. The ceramic sensors consisted of $SiO_2$ of 54.17~71.62wt.%, A1$_2$ $O_3$ of 15.42~33.79wt.% and the rest of 10wt.%, those were Fe$_2$ $O_3$, CaO, MgO, Na$_2$O, $K_2$O, Ti $O_2$, P$_2$ $O_{5}$. The pattern of dropping were changed according to the variety, thickness and firing temperature of ceramics. As the ceramics were made thicker, the fluctuation of dropping became more rapid, but it did not regularly work at 1mm thickness. As the firing temperature of ceramics became higher, the fluctuation of dropped amount became more rapid.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.25 no.7
• /
• pp.906-913
• /
• 2019

To evaluate the removal performance of PO₄-P and NH₃-N, laboratory experiments were conducted by filling a container with oyster shells, pyrolyzed at 100℃ (POS100), 600℃ (POS600) and 800℃ (POS800), and passing artificial wastewaters through the container. The pH in the ef luent was found to increase due to CaO eluted from oyster shell. Removal amounts of PO₄-P of ~23.1 mg/kg, 16.1 mg/kg, and 15.9 mg/kg were obtained when POS100, POS600, and POS800, respectively, were used; therefore, the highest PO₄-P removal amount was obtained when POS100 was used. It is considered that Ca and dolomite in the oyster shells adsorbed and precipitated PO₄-P. Removal amounts of NH₃-N were of ~3.56 mg/kg, 5.72 mg/kg, and 3.97 mg/kg were obtained when POS100, POS600, and POS800, respectively, were used The low removal rate for NH₃-N is probably due to unstable nitrification, use of sealed containers, and the effect of NH₃-N being converted to NH₄⁺ upon increasing pH. Based on these results, pyrolyzed oyster shell is expected to promote changes in PO₄-P and NH₃-N concentrations through chemical reactions. These results can also be used for basic research in the development of wastewater treatment.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.196-196
• /
• 2003

현재 PDP(Plasma Display Panel) 상판의 유전체층은 저온에서 소성이 가능한 저융점 유리가 요구되기 때문에 융점을 낮추기에 용이한 PbO계가 주 성분으로 사용되어 오고 있으나. 최근 환경오염 등의 문제점으로 인해 Pb-free을 추구하는 새로운 유리조성의 연구가 많이 수행되고 있다. 이에 본 연구는 이미 PDP의 격벽과 봉착용 조성으로 많이 연구되어진 비스무스계 유리를 고려하여 PDP의 투명유전체용 조성을 찾고자 한다. Bi$_2$O$_3$-ZnO-SiO$_2$3원계를 기본으로 하는 유리조성에 유리망목형성제등을 첨가하여 열적특성과 광학적 특성을 조사하였다. 열적특성은 DTA를 이용하여 유리 전이 점(Tg) 및 융점(Tl)등을 측정하였고 TMA를 이용하여 선팽창계수(CTE)를 측정하였으며 유리섬유를 제조한 후 Littleton softening point (Ts)를 측정하였다. 광학적 특성은 페이스트를 제조하여 스크린프린팅 후 54$0^{\circ}C$~$600^{\circ}C$에서 1-2 h동안 소성하여 투광성을 조사하였다. 그 결과로, 열적특성으로는 400~5$50^{\circ}C$의 Tg, 450~$600^{\circ}C$의 Ts 및 5~11$\times$$10^{-6}$K의 CTE 값을 나타 내었고 광학적 특성으로 투광성은 양호한 특성(60% 이상)을 나타내었다. Bi$_2$O$_3$ 계를 현재 PDP의 투명유 전체에 적용시키기에는 유리용융시에 높은 점도와 환원 등의 문제점을 갖고 있지만 열적특성과 광학특성면에서는 가능성을 제시하여 향후 연구를 할 가치가 있다고 본다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.471.1-471.1
• /
• 2014

염료감응형 태양전지(DSSC)는 다양한 태양전지 중, 가장 환경친화적이고, 생산단가도 낮을 뿐만 아니라 다양한 색상과 투광성을 확보할 수 있어 많은 연구가 진행되어왔다. 하지만 액체전해질을 사용하는 기존 염료감응형 태양전지는 높은 휘발성과 열 팽창 수축에 따른 전해질 누액의 문제점으로 인하여 최근에는 고체전해질을 이용한 염료감응형 태양전지의 개발이 활발히 이루어지고 있다. 또한 기존 염료보다 높은 흡광계수와 넓은 흡수스펙트럼을 지닌 페로브스카이트가 개발되어 현재 많은 관심이 주목되고 있다. 본 연구에서는 $TiO_2$ 제조상의 중간생성물인 Metatitanic acid (MTA)를 이용하여 광전극을 형성하고 열처리 온도에 따른 나노입자의 소성거동평가을 평가하였고 시차열중량 분석, 결정상 확인을 하고 염료감응 태양전지에 적용하였다. MTA 나노입자를 Field Emission Transmission Electron Microscopy (FE-TEM), Barrett-Joyner-Halenda (BJH pore size distribution)과 Brunauer-Emmet-Teller (BET) 분석을 통해 소성거동을 평가하고, Thermogravimetry and differential thermal analysis (TG-DTA)를 통해 열중량 측정을 하였으며, X-ray Diffraction (XRD) 분석을 통해 결정상을 확인하였다. 또한 Fourier-transform infrared (FT-IR) spectroscopy를 통해 MTA 나노입자의 표면분석을 하였다. 형성된 MTA 광전극을 페로브스카이트 염료에 적용하여 5%의 효율을 달성하였다.