• Transactions of the Korean Society of Mechanical Engineers
• /
• v.13 no.6
• /
• pp.1183-1192
• /
• 1989

본 논문에서는 평면변형률 상태하에서 안정하게 성장하는 균열선단에 집중 되어있는 강소성역의 해석에 역점을 두어 재결정법과 탄.소성유한요소법을 도입하여 안정 성장균열 선단에 형성되는 균열 성장저항에 직접적인 영향을 미치고 있는 소성 역의 크기나 형태에 대한 실험 및 해석을 하였다.

• Journal of Ocean Engineering and Technology
• /
• v.2 no.2
• /
• pp.71-77
• /
• 1988

For the collapse of structures due to the variable repeated load, two types of collapse mechanisms, i.e., incremental collapse and alternating plasticity, exist. Under the similar variable repeated loading conditions there exists shakedown state in the structures. In shakedown state, the number of plastic hinges are not increased and all further loading will be resulted in the elastic moment changes. Namely, under the shakedown state, structures do not collapse. In this investigation, shakedown analysis are performed by composing new computer programs. Basic theories employed to compose the programs are as follows. 1. Newton-Raphson methods are added to the existing matrix method for the plastic analysis. 2. An effort to construct the stiffness of axial and bending springs attached at both ends of the member has been made. By using the programs developed, it is possible to anticipate the collapse mechanisms (Incremental collapse, alternating plasticity). Lastly for the verification of performance of the program, demonstration examples have been solved and the results are compared with other sources.

• Journal of the Korea Concrete Institute
• /
• v.13 no.6
• /
• pp.637-644
• /
• 2001

A regularization method based on the Duvaut-Lions viscoplastic scheme for plastic-damage and continuum damage models, which provides mesh-independent and well-posed solutions in nonlinear earthquake analysis of concrete dams, is presented. A plastic-damage model regularized using the proposed rate-dependent viscosity method and its original rate-independent version are used for the earthquake damage analysis of a concrete dam to analyze the effect of the regualarization and mesh. The computational analysis shows that the regularized plastic-damage model gives well-posed solutions regardless mesh size and arrangement, while the rate-independent counterpart produces mesh-dependent ill-posed results.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.4
• /
• pp.718-725
• /
• 2016

In this study, the plastic flow curve of commercially pure titanium sheet (CP Ti) actively used in the plate heat exchanger etc., was evaluated. The plastic flow curve known as hardening curve is a key factor needed in conducting finite element analyses (FEA) for the forming process of a sheet material. A hydraulic bulge test was performed on the CP Ti sheet and the strain in this test was measured using the DIC method and ARAMIS system. The measured true stress-true strain curve from the hydraulic bulge test (HBT) was compared with that from the tensile test. The measured true stress-true strain curve from the hydraulic bulge test showed stable plastic flow curve over the strain range of 0.7 which cannot be obtained in the case of the uniaxial tensile test. The measured true stress-true strain curve from the hydraulic bulge test can be fitted well by the hardening equation known as the Kim-Tuan model.

• Tunnel and Underground Space
• /
• v.14 no.3
• /
• pp.215-228
• /
• 2004

Rock mass contains discontinuities such as faults and joints, and their mechanical properties and spatial distribution dominate the stability of rock mass. Because the deformation of rock mass occurs discontinuities in many cases. However in the case of poor quality rock mass under high stresses, the deformation along intact rock can also influence the structure's stability. In this study, two dimensional finite element program was developed with a rheological model to analyze the stability of the structure excavated in jointed rock mass. The “equivalent material” approach was used assuming intact rock, joints and rock bolts as visco-plastic materials. The program was verified by analysing an intact rock model, a jointed rock mass model and a reinforced jointed rock mass model. The displacement was examined in each model with changing the intact rock behaviour as elastic and visco-plastic. In the case of poor quality rock mass under high stresses, e assumption of visco-plastic behaviour of intact rock resulted in larger displacement than when assuming elastic behaviour for intact rock. Therefore it is recommended to add intact rock's visco-plastic behaviour to the existing model, which only assumes visco-plastic behaviour of joints and rock bolts.

• International Journal of Highway Engineering
• /
• v.11 no.4
• /
• pp.25-31
• /
• 2009

In general, it is well known fact that the stone mastic asphalt (SMA) pavement has a high resistance against rutting. However, performance of SMA is not well measured by general method used in the laboratory. The objective of this study is to investigate an applicability of deformation strength ($S_D$) for performance estimation of SMA, and to find out the correlation between rut depth and dynamic stability, and $S_D$ of SMA. This study carried out wheel tracking test and Kim-test with optimum asphalt content (OAC) determined by mix design. The results indicated that the $S_D$ of SMA was very poorer than those of dense-graded asphalt mixtures. $S_D$ showed similar WT dynamic stability and rut-depth level. It was found that Kim-test was not reflected higher rutting resistance of SMA like as indirect tensile strength (ITS) test and Marshall stability test. Also, it was revealed that dynamic stability and rut-depth of WT had some problems to estimate rutting resistance of SMA mixtures.

• Journal of the Microelectronics and Packaging Society
• /
• v.6 no.3
• /
• pp.25-35
• /
• 1999

LTCC (Low Temperature Cofired Ceramic) or LTCC-M (Low Temperature Cofired ceramic on Metal) technology is one of MCM-C (Multichip Module on Ceramic) technologies and becomes to be widely used in consumer, RF and automotive electronics. As green sheets for LTCC are cofired below $1000^{\circ}C$ in comparison with those for HTCC (High Temperature Cofired Ceramic), high conductivity metal traces such as gold, silver and copper can be used. The dimensional stability in LTCC-M technology enables embedded passives to be integrated inside modules, which enhances the electrical performance and increases the reliability of the modules. Coefficient of thermal expansion and dielectric constant can be controlled by changing composition and heating profile for cofiring. In this technical review, LTCC and LTCC-M technologies are introduced and advantages of those technologies are explained.

• International Journal of Highway Engineering
• /
• v.6 no.4 s.22
• /
• pp.65-73
• /
• 2004

Marshall stability and flow don't reflect mechanical property of asphalt mixtures and have little correlation with rutting-related performance. There is often rutting occurred on the asphalt pavement which was constructed using a mixture passing the specification for stability and flow. This study dealt with comparison of volumetric properties of mixtures from Marshall mix design and from Superpave mix design. This study used one binder, three aggregates and two gradations. The mixtures were manufactured by each mix design method. Result showed that OAC, VMA and VFA by Marshall mix design were higher than those by Superpave mix design. This is because Mashall mixture has the gradation prone to rutting and it should be further investigated whether or not the high OAC is direct cause of rutting in asphalt pavement.

• Economic and Environmental Geology
• /
• v.56 no.6
• /
• pp.899-909
• /
• 2023

In this study, the material scientific characteristics of Hobun pigments used as white inorganic pigment for traditional cultural heritage were identified according to the type of shell and calcination and evaluated the stability of the preservation environment. For the purpose of this, we collected 2 different types of Hobun pigments made by oyster and clam shell and its calcined products(at 1,150℃). Hobun pigments before calcined identified calcium carbonate such as calcite, aragonite but calcination derived changing main composition to portlandite and calcite. Results of FE-SEM showed characteristics microstructure for each shell but pigments after calcined observed porous structure. Porous granule highly caused oil adsorption according to increase specific surface area of pigments. In addition, the whiteness improved after calcined pigments compared to non-calcined pigments, and the color improvement rate of Hobun pigment (CS) which made of clam shell was higher. As a result of the accelerated weathering test, the Hobun pigment-colored specimen had a color difference value of less than 2 after the test, which was difficult to recognize with the naked eye. In particular, the color stability has improved as the color difference value of the Hobun pigment is smaller after calcined compared to before non-calcined pigment. However, it was confirmed that the stability of the painting layer was lower in the specimen after calcined pigment. For antifungal activity test, Aspergillus niger, Tyromyces palustris and Trametes versicolor were used as test fungi, and all pigments were found to have preventive and protective effects against fungi. Especially, the antifungal effect of the calcined pigment was excellent, which is due to the stronger basicity of the pigment.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.6
• /
• pp.3888-3893
• /
• 2014

The number of waste tires is increasing. One effective recycling method is the pyrolysis of waste tires. Using the pyrolyzed carbon black from waste tires, the characteristics of permanent deformation for PA-13mm porous mixture were evaluated. The confining pressure of 138 kPa and deviatoric stress of 551 kPa were adopted. The testing temperature was $45^{\circ}$ and 50 gyrations of the gyratory compactor was used to simulate the medium traffic level. The mixture modified by 10% PCB showed the largest Marshall Stability of 3.41 kN. The stability of the mixtures with PCB was 50% higher than that of mixture without PCB. The limited laboratory test showed that the use of PCB in a porous pavement decreases the permanent deformation and will be an effective alternative method to reducing the permanent deformation of a porous pavement.