• Journal of Korean Society of Steel Construction
• /
• v.14 no.1
• /
• pp.13-21
• /
• 2002

In this paper, 3-D frame design using refined plastic-hinge analysis accounting for local buckling is developed. This analysis accounts for material and geometric nonlinearities of the structural system and its component members. Moreover, the problem associated with conventional refined plastic-hinge analyses, which do not consider the degradation of the flexural strength caused by local buckling, is overcome. Efficient ways of assessing steel frame behavior including gradual yielding associated with residual stresses and flexure, second-order effect, and geometric imperfections are presented. In this study, a model consisting of the width-thickness ratio is used to account for local buckling. The proposed analysis is verified by the comparison of the LRFD results. A case study shows that local buckling is a very crucial element to be considered in second-order plastic-hinge analysis. The proposed analysis is shown to be an efficient, reliable tool ready to be implemented into design practice.

• Journal of the Korean Ceramic Society
• /
• v.40 no.12
• /
• pp.1177-1182
• /
• 2003

The porous sensing materials for BaTiO$_3$ gas sensors were fabricated by adding the graphite powders. The crystalline structure and microstructure of the porous BaTiO$_3$-based ceramics were studied. All the sintered bodies showed a tetragonal perovskite structure. The porosity increased with increasing graphite contents. This is mainly due to an enhanced evolution of CO and $CO_2$ gases resulting from the exothermic reactions of graphite and oxygen during the sintering. It was found that the discrepancy in the resistivities measured in air and CO atmospheres at high temperatures (>∼20$0^{\circ}C$) became remarkable with increasing temperature. The sensitivity of CO gas increased with porosity, since the reactions between CO gas and $O_2$$^{[-10]}$ and between CO gas and $O^{[-10]}$ are active due to the formation of many reaction sites. The porous BaTiO$_3$-based ceramics could be promising as a sensing material for CO gas sensors.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.2
• /
• pp.1579-1584
• /
• 2015

In photocatalytic reaction, the doping of metal matter can alter the titania surface properties. As such the metal matter can increase the rate of the reaction. The influence of metal doping and calcination condition of $TiO_2$ photocatalyst was investigated at the batch-type photoreactor. Several metal matters were doped to the $TiO_2$ catalyst to improve photodegradation efficiency. During the experiments, water content was 3wt%, and reactor temperature was $40^{\circ}C$. Palladium-doped $TiO_2$ was found to be the best, where as platinum or tungsten-added also showed good results. Additional doping of platinum or tungsten on Pd/$TiO_2$ had no increase on the removal efficiency. To obtain proper calcination condition, various experiments about calcination temperature and time were carried out. As a result, the optimum calcination condition was temperature of $400^{\circ}C$, time of 1 hour.

• International Journal of Highway Engineering
• /
• v.11 no.4
• /
• pp.25-31
• /
• 2009

In general, it is well known fact that the stone mastic asphalt (SMA) pavement has a high resistance against rutting. However, performance of SMA is not well measured by general method used in the laboratory. The objective of this study is to investigate an applicability of deformation strength ($S_D$) for performance estimation of SMA, and to find out the correlation between rut depth and dynamic stability, and $S_D$ of SMA. This study carried out wheel tracking test and Kim-test with optimum asphalt content (OAC) determined by mix design. The results indicated that the $S_D$ of SMA was very poorer than those of dense-graded asphalt mixtures. $S_D$ showed similar WT dynamic stability and rut-depth level. It was found that Kim-test was not reflected higher rutting resistance of SMA like as indirect tensile strength (ITS) test and Marshall stability test. Also, it was revealed that dynamic stability and rut-depth of WT had some problems to estimate rutting resistance of SMA mixtures.

• International Journal of Highway Engineering
• /
• v.9 no.4
• /
• pp.135-147
• /
• 2007

Segregation in asphalt pavements occurs as a result of the non-uniform distribution of coarse and fine aggregates and causes premature distresses, such as cracking, raveling, and stripping. The effect of segregation on rutting, however, has not been clearly identified. Experimental and analytical work performed in this study indicates that rutting performance is affected by segregation of mixtures. However, the aggregate structure of mixtures appears to be a more critical factor that determines the rutting performance, rather than the level of segregation. Based on the field mixtures evaluated, an increase of coarse aggregate volume in an asphalt mixture is an important factor that results in good rutting performance. This effect holds true for mixtures with lower levels of air voids, but for mixtures with higher levels of air voids, the air voids effect becomes dominant, resulting in a reduction in rutting performance. An air void content of 10% appears to be a threshold that determines the rutting performance of Superpave mixtures. Once the air void content exceeds 10%, the rutting performance of Superpave mixtures decreases significantly, despite the coarse aggregate volume.

• Resources Recycling
• /
• v.29 no.6
• /
• pp.48-56
• /
• 2020

In this study, raw mix was mixed with CaCl2 for analyzing characteristics of clinker added chlorine and chlorine was added by 2,000ppm at high concentration condition. The raw mix added chlorine was burned at 1250℃~1350℃ and maintained during 10minutes at each maximum temperature. Clinker target modulus was LSF 92, SM 2.5 and IM 1.6 in this study. The burnability of clinker added chlorine was identified by free-CaO content. Free-CaO content decreased as chlorine content increased and free-CaO content of 1350℃-2000ppm clinker decreased by 1.5%. Optical microscope and XRD Analyses were used for identify mineral properties of clinker added chlorine. The mineral of clinker could not be observed at 1250℃ and the size of alite grew larger as chlorine content increased at 1350℃. It showed a good crystallizability as chlorine content increased. As chlorine content of clinker increased, clinker showed a good burnability and mineral property.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.8 no.4
• /
• pp.514-519
• /
• 2020

In this study, cement clinkers were sintered at each temperature by replacing some of the clay components of cement clinkers with coal materials. The mineral phase change of sintered cement clinker was quantitatively analyzed by XRD-Rietveld method. As the sintering temperature of cement clinker increased, the amount of belite decreased, the amount of alite increased, and the amount of free-CaO decreased. The form of alite and belite could be distinguished at sintering temperature of 1450℃ or higher. The crystal size was greatly increased at 1500℃ sintering. It was confirmed that the excessive sintering was progressed. Free-CaO decreased with the increase of sintering temperature. At 1450 ℃ or higher, it was less than 0.5%. In 1450℃ or greater, it is determined that enough sintering is included. Therefore, the application of fly ash as a raw material of cement clinker was judged to be usable as a source of chemical components of alumina and iron raw materials.

• Journal of the Korean Wood Science and Technology
• /
• v.30 no.2
• /
• pp.115-120
• /
• 2002

Woodceramics are new porous carbon materials obtained by burning wood or woody materials impregnated with thermosetting resin in a vacuum furnace. In this paper, the change of dimensions and bending strength of woodceramics which were made from medium density fiberboard have been investigated to examination the possibility of utilization as a woodceramics materials. 1) An increasing rate of dimension in impregnated board increased with increasing resin impregnation rate. And increasing rate of thickness was higher than that of length. 2) When the resin impregnation rate increased, the bending strength of impregnated board had a tendency to increase. 3) The rates of weight loss, length and thickness reduction of woodceramics showed a slight increase with increased burning temperature. 4) The density of woodceramics showed a increase from at 500℃ till at 800℃ with increasing burning temperature but decrease at 1,000℃ 5) When the burning temperature increased, the bending strength of woodceramics had a tendency to increase.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.6A
• /
• pp.1033-1039
• /
• 2006

The purpose of this study are to evaluated bond, flexural properties and control of plastic shrinkage cracking of crimped type synthetic fiber with amplitude 6 mm and height 1.8 mm reinforced cement based composites. Bond and flexural test were conducted in accordance with the JCI-SF 8 and JCI SF-4 standard, respectively. The plastic shrinkage cracking test was conducted for evaluating the effect of fiber in reducing shrinkage cracking in cement based composites. Test results indicated that the crimped typel synthetic fibers performed significantly better than the straight type fiber in terms of interface toughness and pullout load and the crimped type synthetic fibers improved the flexural toughness of concrete. Also, the increasing the crimped type synthetic fiber volume fraction from 0.00% to 1.00% improved the plastic shrinkage cracking resistance. Specially, the effect of control of plastic shrinkage cracking is excellent at the more than 0.5% fibre volume fraction.

• Economic and Environmental Geology
• /
• v.56 no.6
• /
• pp.899-909
• /
• 2023

In this study, the material scientific characteristics of Hobun pigments used as white inorganic pigment for traditional cultural heritage were identified according to the type of shell and calcination and evaluated the stability of the preservation environment. For the purpose of this, we collected 2 different types of Hobun pigments made by oyster and clam shell and its calcined products(at 1,150℃). Hobun pigments before calcined identified calcium carbonate such as calcite, aragonite but calcination derived changing main composition to portlandite and calcite. Results of FE-SEM showed characteristics microstructure for each shell but pigments after calcined observed porous structure. Porous granule highly caused oil adsorption according to increase specific surface area of pigments. In addition, the whiteness improved after calcined pigments compared to non-calcined pigments, and the color improvement rate of Hobun pigment (CS) which made of clam shell was higher. As a result of the accelerated weathering test, the Hobun pigment-colored specimen had a color difference value of less than 2 after the test, which was difficult to recognize with the naked eye. In particular, the color stability has improved as the color difference value of the Hobun pigment is smaller after calcined compared to before non-calcined pigment. However, it was confirmed that the stability of the painting layer was lower in the specimen after calcined pigment. For antifungal activity test, Aspergillus niger, Tyromyces palustris and Trametes versicolor were used as test fungi, and all pigments were found to have preventive and protective effects against fungi. Especially, the antifungal effect of the calcined pigment was excellent, which is due to the stronger basicity of the pigment.