• The Journal of the Korea institute of electronic communication sciences
• /
• v.14 no.1
• /
• pp.81-86
• /
• 2019

This paper is concerned with a system design that enables a the plurality of switching mode power supplies to be supplied with larger power through a parallel connection. For this purpose, a shunt resistor is placed in series at the output of the constant voltage regulator and the output voltage is sensed and controlled using an arduino. In this paper, two constant-voltage regulators were used for the experiment, but it is possible to generalize for more boards. By using the method that controls the system, the sum of the currents delivered by the two systems to the load was found to be 96% of the current drawn from each board. In case of efficiency, 92.4% efficiency is achieved in the unit board and the efficiency in parallel connection is about 90%.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.31 no.2
• /
• pp.107-111
• /
• 2018

In this study, we designed the temperature coefficient of resistance (TCR) and heat radiation properties of shunt fixed resistors by adjusting the atomic composition of a metal alloy resistor, and fabricated a resistor that satisfied the designed properties. Resistors with similar atomic composition of copper and nickel showed low TCR and excellent shunt fixed resistor properties such as short-time overload, rated load, humidity load, and high temperature load. Finally, we expect that improved sensor accuracy will be obtained in current-distribution-type shunt fixed resistor for IoT sensors by designing the atomic composition of the metal alloy resistor proposed in this work.

• The Journal of the Acoustical Society of Korea
• /
• v.21 no.2
• /
• pp.150-159
• /
• 2002

The possibility of a broadband noise reduction of piezoelectric smart panels is experimentally studied. Piezoelectric smart panel is basically a plate structure on which piezoelectric patch with shunt circuits is mounted and sound absorbing material is bonded on the surface of the structure. Sound absorbing materials can absorb the sound transmitted at mid frequency region effectively while the use of piezoelectric shunt damping can reduce the transmission at resonance frequencies of the panel structure. To be able to tune the piezoelectric shunt circuit, the measured electrical impedance model is adopted. Resonant shunt circuit composed of register and inductor in stories is considered and the circuit parameters are determined based on maximizing the dissipated energy through the circuit. The transmitted noise reduction performance of smart panels is investigated using an acoustic tunnel. The tunnel is a square crosses sectional tunnel and a loud speaker is mounted at one side of the tunnel as a sound source. Panels are mounted in the middle of the tunnel and the transmitted sound pressure across the panels is measured. Noise reduction performance of a double smart panel possessing absorbing material and air gap shows a good result at mid frequency region except the first resonance frequency. By enabling the piezoelectric shunt damping, noise reduction is achieved at the resonance frequency as well. Piezoelectric smart panels incorporating passive method and piezoelectric shunt damping are a promising technology for noise reduction in a broadband frequency.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.1
• /
• pp.634-638
• /
• 2015

Phase currents should be measured in real time for vector control of a 2-phase induction motor. Generally, the phase currents of the motor are measured using two Hall current sensors installed at the output terminal of an inverter. Unfortunately, Hall current sensors are expensive and uneconomical because a vector-controlled inverter for 2-phase induction motor is mainly used in low-power and low-price applications. This paper proposes a low-cost current measurement method using two shunt resistors instead of expensive Hall current sensors. The proposed method can measure the phase currents under all operating conditions of the motor. This method was applied to an experimental vector-controlled inverter for 2-phase induction motor of 220[V]/360[W] and was verified through computer simulations and experimentation.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.32 no.5
• /
• pp.403-406
• /
• 2019

We prepared yarned carbon nanotube (CNT) fibers from a CNT forest synthesized on a Si wafer by chemical vapor deposition (CVD). The yarned CNT fibers were thermally annealed to reduce their resistance by removing the amorphous carbonaceous impurities present in the fibers. The resistance of the yarned CNT fiber gradually decreased with an increase in the annealing temperature from $200^{\circ}C$ to $400^{\circ}C$ but increased again above $450^{\circ}C$. We carried out thermogravimetric analysis (TGA) to confirm the burning properties of the amorphous carbonaceous impurities and the crystalline CNTs present in the fibers. The pattern of the mass change of the sample CNT fibers was very similar to that of the resistance change. We conclude that CNT fibers should be thermally annealed at temperatures below $400^{\circ}C$ for reducing and stabilizing their resistance.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.55 no.5
• /
• pp.250-256
• /
• 2006

Both ratio error and phase angle error in current transformer(CT) depend critically on values of CT burden. Thus, precise measurement of CT burden is very important for the evaluation of CT. A method for the measurement of CT burden has been developed by employing the portable shunt precise resistor with negligible AC-DC resistance difference less than $10^{-5}$. The burden value(value and power factor) can be calculated from resistance and reactance obtained by measuring the change of ratio error and phase angle error caused by the change of shunt resistor. The uncertainty for the method is evaluated and found to be abut 2 %.

• Proceedings of the KIEE Conference
• /
• 2004.11a
• /
• pp.17-19
• /
• 2004

트렌치 게이트 구조를 통해 순방향 전압 강하 손실 없이 기생 사이리스터 래치-업을 억제시키는 새로운 수평형 절연 게이트 바이폴라 트랜지스터 (LIGBT)를 제안하였다. 제안된 소자의 베이스 션트 저항은 정공의 우회로 인하여 감소하였으며, 이에 따라 기생 사이리스터 래치-업이 억제되었다. 제안된 소자의 순방향 전압강하는 트렌치 구조에 의한 유효 채널 폭 증가로 감소하였다. 제안된 소자의 동작 원리 분석을 위해 ISE-TCAD를 이용한 3차원 시뮬레이션을 수행하였으며, 표준 CMOS 공정을 이용하여 소자를 제작 및 측정하였다. 제안된 소자의 순방향 전압 강하는 기존의 LIGBT에 비해 증가하지 않았으며, 래치-업 용량은 2배로 향상되었다. 제안된 소자의 포화 전류는 감소하였으며, 이로 인하여 소자의 강인성 (ruggedness)이 향상되었다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.2 no.2
• /
• pp.49-56
• /
• 2001

The possibility of a noise reduction of piezoelectric single Panels is experimentally studied. Piezoelectric single panel is basically a plate structure on which piezoelectric patch with shunt circuit is mounted. The use of piezoelectric shunt damping can reduce the transmission at resonance frequencies of the panel structure. Piezo-damping is implemented by using a newly proposed tuning method. This method is based on electrical impedance model and maximizing the dissipated energy at the shunt circuit. By measuring the electrical impedance at the piezoelectric patch bonded on a structure, an equivalent electrical model is constructed near the system resonance frequency. Resonant shunt circuit for piezoelectric shunt damping is composed of register and inductor in series, and they are determined by maximizing the dissipated energy throughout the circuit. The transmitted noise reduction performance of single Panel is tested on an acoustic tunnel. The tunnel is a tube with a square cross section and a loud speaker is mounted at one side of the tube as a sound source. Panels are mounted in the middle of the tunnel and the transmitted sound pressure across Panels is measured. By enabling the piezoelectric shunt damping noise reduction is achieved at the resonance frequencies as well. Piezoelectric single panel with piezoelectric shunt damping is a promising technology for noise reduction in a broadband frequency.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.3 no.1
• /
• pp.49-57
• /
• 2002

The possibility of a transmission noise reduction of piezoelectric smart panels using piezoelectric shunt damping is experimentally studied. Piezoelectric smart panel is basically a plate structure on which piezoelectric patch with shunt circuits is mounted and sound absorbing materials are bonded on the surface of the structure. Sound absorbing materials can absorb the sound transmitted at mid frequency region effectively while the use of piezoelectric shunt damping can reduce the transmission at resonance frequencies of the panel structure. To be able to reduce the sound transmission at low panel resonances, piezoelectric damping using the measured electrical impedance model is adopted. Resonant shunt circuit for piezoelectric shunt damping is composed of register and inductor in series, and they are determined by maximizing the dissipated energy throughout the circuit. The transmitted noise reduction performance of smart panels is investigated using an acoustic tunnel. The tunnel is a tube with square crosses section and a loud-speaker is mounted at one side of the tube as a sound source. Panels are mounted in the middle of the tunnel and the transmitted sound pressure across panels is measured. Noise reduction performance of a smart panels possessing absorbing material and/or air gap shows a good result at mid frequency region but little effect in the resonance frequency. By enabling the piezoelectric shunt damping, noise reduction of 10dB, 8dB is achieved at the resonance frequencise as well. Piezoelectric smart panels incorporating passive method and piezoelectric shunt damping are a promising technology for noise reduction in a broadband frequency.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.21 no.4
• /
• pp.343-350
• /
• 2016

Generally, the average phase current is sampled at the midpoint of a PWM signal for the vector control of an AC motor. The three-phase current can also be reconstructed from a DC-link shunt resistor by sampling the shunt voltage during the active vectors of the SVPWM. However, the reconstructed current is different from the average current because of the deviation of the sampling point from the midpoint of the PWM signal. This paper proposes an algorithm to estimate the average current from the reconstructed current in a single-shunt inverter. The proposed method is derived from the phase current slopes based on switching states and corresponding switching time. In addition, the proposed method is generalized for all the six sectors of the space vector hexagon. The validity of the proposed algorithm is verified with simulations and experiments.