• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.10a
• /
• pp.101-105
• /
• 2001

고속절삭을 통해서 생산성과 가공정밀도의 향상을 도모할 수 있기 때문에, 최근 머시닝센터를 중심으로 한 공작기계 주축계의 고속화는 눈부시게 발전하고 있다. 그러나 주축계가 고속화될 수록 증가하는 베어링에서의 발열은 베어링의 수명단축, 주축계의 열변형 증대 등을 초래하고, 궁극적으로 공작기계의 성능을 저하시키게 된다. 따라서 고속으로 회전하는 베어링에서의 발열을 효과적으로 억제할 수 있는 윤활방법에 대한 연구들이 활발히 진행되고 있다. 따라서 본 연구에서는 공작기계용 고속주축계의 냉각특성을 규명하기 위한 노력의 하나로 압축공기를 이용한 고속주축 계의 냉각실험을 수행하였다. 고속주축계의 실험모델은 오일에어윤활방법, 앵귤러콘택트 볼베어링, 이중분사노즐, 냉각 자켓등을 사용해서 제작하였으며, 특히 고속주축계의 공기냉각방법에 대한 유용성은 실험결과로 부터 입증하였다.

• The Magazine of the Society of Air-Conditioning and Refrigerating Engineers of Korea
• /
• v.38 no.7
• /
• pp.29-38
• /
• 2009

지난 20년간 급속한 발전을 통하여 회전 블레이드의 직경이 126 m, 나셀까지의 높이가 약 130 m에 이르는 6,000 kW의 용량을 가지는 풍력발전기가 개발되었다. 세계적으로 풍력발전의 필요성과 중요성이 인식되어 2008년 현재 약 120,000 MW의 설치 용량을 기록하고 있다. 풍력터빈(wind turbine)과 그 부품의 기계적인 성능평가의 종류와 방법은 많은 사람들의 관심인 것으로 판단한다. 우선 풍력터빈을 구성하는 주요 핵심부품은 블레이드, 증속장치, 발전기 등이며, 세부 구성 부품으로 허브, 핏치와 요베어링, 주축베어링, 타워 등이 있다. 주요핵심 부품인 블레이드, 증속기, 발전기 등의 성능평가가 중요한 이슈이다. 또한 모든 구성품을 조립하여 초기의 설계사양에 따라서 제조되고 최종성능이 발휘되는지 여부를 현장시험을 통하여 성능평가과정을 거치게 되는데 이 과정은 풍력터빈의 성능평가라고 하며 주요 평가대상은 출력성능(power performance), 소음(noise), 하중(load), 전력품질(power quality) 등 4가지 항목을 집중적으로 측정하여 개발된 풍력터빈의 전반적인 성능을 평가하게 된다. 본 투고에서는 핵심부품인 블레이드, 증속기, 발전기에 대한 시험기술과 풍력터빈의 성능평가 항목인 4개 측정 항목에 대하여 기술하였다.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.12 no.12
• /
• pp.929-934
• /
• 2002

This paper considers the vibration Problem of vehicle driveline which consists of two propeller shafts and the center bearing. The excessive vibration occurs at the center bearing when the vehicle starts to run. Using the kinematic constraints at the universal joint between two propeller shafts, we developed an one d.o.f model which describes the radial motion of the center bearing. We found out that the vibration occurs at the specific vehicle speed corresponding to the natural frequency of the model. Comparing the simulation results with test results we also show that the vibration at low vehicle speed is caused primarily by the feint angle and secondarily by the mis-aligned yoke flange rather than by the unbalance.

• Journal of the Korean Society for Precision Engineering
• /
• v.14 no.8
• /
• pp.92-100
• /
• 1997

An upper-bound elemental technique (UBET) analysis is carried out to improve the material flow and to reduce the load of bearing-race forming process. The UBET analysis, which adapts the advantages of stream function and finite element method, is useful for predicting the profile of complex geometric bound- ary. From the UBET analysis, the forming load, the velocity distribution and the stream line of the deformed billet are determined by minimizing the total power consumption with respect to chosen parameters. The results of present UBET analysis are better than those of previous UBET analysis. Experiments have been carried out with model material plasticine billets at room temperature. The theoretical predictions for forming load and flow pattern(stream line) are in good agreement with the experimental results.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.21 no.3
• /
• pp.372-377
• /
• 2011

This paper propose the robust stability algorithm for controlling a hybrid magnetic bearing system. The control object in the magnetic bearing system enables the rotor to rotate without any physical contact by using magnetic force. Generally, the system dynamics of the magnetic bearing system has severe nonlinearity and uncertainty so that it is not easy to obtain the control objective. For solving these problems, we propose the fuzzy modelling and robust control algorithm for hybrind magnetic bearing system. The sufficient conditions for robust controller are obtained in terms of solutions to linear matrix inequalities (LMIs). Simulation results for HMB are demonstrated to visualize the feasibility of the proposed method.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.22 no.3
• /
• pp.267-272
• /
• 2012

This paper propose the implementation of robust fuzzy controller for controlling an active magnetic bearing (AMB) system with 6 degree of freedom (DOF). A basic model with 6 DOF rotor dynamics and electromagnetic force equations for conical magnetic bearings is proposed. The developed model has severe nonlinearity and uncertainty so that it is not easy to obtain the control objective. For solving this problem, we use the Takagi-Sugeno (T-S) fuzzy model which is suitable for designing fuzzy controller. The control object in the AMB system enables the rotor to rotate without any phsical contact by using magnetic force. In this paper, we analyze the nonlinearity of the active magnetic bearing system by using fuzzy control algorithm and desing the robust control algorithm for solving the parameter variation. Simulation results for AMB are demonstrated to visualize the feasibility of the proposed method.

• Tribology and Lubricants
• /
• v.34 no.6
• /
• pp.254-261
• /
• 2018

In order to reduce resistance torque and energy loss, minimizing friction between race surface and rolling elements of a bearing is necessary. Recently, to reduce friction in bearing element, solid lubricant coating for the bearing raceway surface has been receiving much attention. Considering the operating conditions of real bearings, verifying the effect of solid lubricant coatings under extreme conditions of high load that is more than 1 GPa is necessary. In this study, we evaluated the friction and wear characteristics of SUJ2 bearing steels deposited by carbon-based coatings (Si-DLC, ta-C), $MoS_2$ and graphite. In case of $MoS_2$ and graphite coatings, different surface treatments were applied to the coatings to verify the effect of surface treatment. A pin-on-disc type tribotester was used to evaluate the tribological characteristics of the coatings. It was possible to quantitatively estimate the friction and wear characteristics of solid lubricant under dry and lubrication conditions. The carbon-based coatings improved the friction and wear properties of SUJ2 bearing steels under the high load condition, but $MoS_2$ and graphite coatings were not suitable for high load conditions due to its low hardness. Different friction and wear behaviors were found for different substrate surface treatment method. Also, it was confirmed that solid lubricant coatings had a more positive effect than just applying the lubricant for improving the tribological characteristics.

• Tribology and Lubricants
• /
• v.36 no.6
• /
• pp.332-341
• /
• 2020

High-speed turbomachinery implements gas foil bearings (GFBs) due to their distinctive advantages, such as high efficiency, lesser part count, and lower weight. This paper provides the test results of the static structural stiffnesses and loss factors of bump-type foil thrust bearings with increasing preload and bearing deflection. The focus of the current work is to experimentally quantify variability in structural stiffnesses and loss factors among the four test thrust bearings with identical design values and material of the bump and top foil geometries using the same (open-source) fabrication method. A simple test setup, using a rigidly mounted non-rotating shaft and thrust disk, measures the bearing bump deflections with increasing static loads on the test bearing. The inner and outer diameters of the test bearings are 41 mm and 81 mm, respectively. The loss factor, best-representing energy dissipation in the test bearings, is estimated from the area inside the local hysteresis loop of the load versus the bearing deflection curve. The measurements show that structural stiffnesses and loss factors of the test bearings significantly rely on applied preloads and bearing deflections. Local structural stiffnesses of the test bearings increase with applied preloads but decrease with bearing deflections. Changes of loss factors are less sensitive to applied preloads and bearing deflections compared to those of structural stiffnesses. Up to 35% variability in static load structural stiffnesses is found between bearings, while up to 30% variability in loss factors is found between bearings.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.26-31
• /
• 2002

The recent machine tools are requested so high-quality processing and productivity increasing. Therefore, it is so necessary to develop technology fur high-speed and high-precision. This thesis touches on the development of high speed and intellectual line center. At first, the line center is necessary that strong structure, compact structure and light weight design for high-speed processing and transfer. So, it is necessary that examination of new materials and structures for light-weight and control devices for precision processing. So. it is going to make mention of the process of 1st model production for the above-mentioned based on test model production and evaluation.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.05a
• /
• pp.318-318
• /
• 2004

원통 연삭기(cylindrical grinding machine)는 원통형 공작물을 센터나 척으로 지지하면서 연삭 공정을 수행하기 때문에 연속적인 작업이 어렵지만, 무심 연삭기(centerless grinding machine)는 원통형 공작물을 받침판으로 지지하면서 연삭 숫돌(grinding wheel)과 조정 숫돌(regulating wheel)로 연삭 공정과 축방향 이송을 동시에 수행하기 때문에 연속적인 작업이 가능하다. 특히 고정밀 부품을 작업자의 숙련도와 무관하게 고능률적으로 가공할 수 있는 무심 연삭기는 구름 베어링, 축, 피스톤 핀 등과 같은 고정밀 기계류 부품들을 대량 연삭하기 위한 용도로 많이 사용되어 왔다.(중략)