• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.4A
• /
• pp.466-471
• /
• 2004

This paper proposes an advanced circuit for fingerprint sensor signal processing. We increased the voltage between ridge and valley by modifying the parasitic capacitance eliminating circuit of sensor plate. The analog comparator was designed for comparing the sensor signal voltage with the reference signal voltage. 1-Pixel Fingerprint sensor circuit was designed and simulated, and the layout was performed.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.5 no.2
• /
• pp.132-136
• /
• 2004

A flat type $NO_2$ micro gas sensor was fabricated by MEMS technology. In order to heat up gas sensing material such as $WO_3$ to a target temperature, a micro hotplate was built on the gas sensor. The temperature distribution of micro gas sensor was analyzed by a CFD program, FLUENT. The results showed that the temperature of silicon wafer base was almost similar to that of the room temperature, which indicates that the heat generated at the micro hotplate heated up effectively the sensing material and its thermal isolation was kept. The uniformity of temperature on the sensing material can be improved by modifying the shape of micro hotplate.

• Proceedings of the KAIS Fall Conference
• /
• 2003.06a
• /
• pp.119-121
• /
• 2003

마이크로 가스센서를 개발하기 위하여 가장 핵심적인 부품인 마이크로 핫플레이트에 대한 열전달을 해석하였다. 상용 열유동 해석 전용 프로그램인 FUENT를 이용하여 발열부와 주위의 실리콘 기판의 온도분포를 구하였다. 발열부에서는 전기저항에 의해서 일정한 양의 열이 균일하게 발생한다고 가정하고 그 열이 실리콘 기판의 끝을 통하여 빠져나간다고 가정하여 정상상태의 온도분포를 구하였다. 해석한 온도분포를 이용하여 균일한 온도분포를 얻을 수 있도록 발열선의 배치를 변화시켜가며 마이크로 핫플레이트의 설계를 완성하였다.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2019.10a
• /
• pp.335-337
• /
• 2019

본 연구에서는 키넥트와 아두이노 초음파센서를 이용하여 야구 경기 시 발생하는 센서 데이터를 획득하여 스트라이크 판단이 가능한 알고리즘 및 디바이스를 개발하였다. 개발된 디바이스는 야구 경기장 홈플레이트로 사용하며 스트라이크, 볼의 경우에 대해 판단하도록 하였다. 판단에는 스트라이크 존을 측정하기 위해 키넥트의 skeleton tracking 예제로 관절을 측정해 좌표를 알아내고 아두이노 초음파센서를 사용하여 스트라이크를 판단하도록 했다.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.5
• /
• pp.152-159
• /
• 2016

This paper describes an offset and 1/f noise cancellation technique based hall sensor signal processor. The hall sensor outputs a hall voltage from the input magnetic field, which direction is orthogonal to hall plate. The two major elements to complete the hall sensor operation are: the one is a hall sensor to generate hall voltage from input magentic field, and the other one is a hall signal process system to cancel the offset and 1/f noise of hall signal. The proposed hall sensor splits the hall signal and unwanted signals(i.e. offset and 1/f noise) using a spinning current biasing technique and chopper stabilizer. The hall signal converted to 100 kHz and unwanted signals stay around DC frequency pass through chopper stabilizer. The unwanted signals are bloked by highpass filter which, 60 kHz cut off freqyency. Therefore only pure hall signal is enter the ADC(analog to dogital converter) for digitalize. The hall signal and unwanted signal at the output of an amplifer and highpass filter, which increase the power level of hall signal and cancel the unwanted signals are -53.9 dBm @ 100 kHz and -101.3 dBm @ 10 kHz. The ADC output of hall sensor signal process system has -5.0 dBm hall signal at 100 kHz frequency and -55.0 dBm unwanted signals at 10 kHz frequency.

• Journal of Sensor Science and Technology
• /
• v.10 no.4
• /
• pp.214-221
• /
• 2001

The use of an asymmetric Mach-Zehnder interferometric amplitude modulator to measure a relatively low frequency electric field strength is described. The sensitivity of an electric field sensor using a $Ti:LiMbO_3$ optical modulator is strongly affected by the shape of a electrode(probe antenna). To measure the low frequency electric field, a probe antenna of wide effective area is more useful than the usual dipole antenna. As a proof of this, the optical modulator was fabricated with a plate-type probe antenna and the usefulness of this antenna tested for measuring low frequency electric field strength. Measurements were performed in the range 0.1 V/cm to 60 V/cm at 60Hz through 100 kHz. Using a probe antenna of $10\;mm{\times}10\;mm$, the output voltage of $10^{-2}\;mV$ was measured with respect to the electric field strength of 0.1 V/cm at 60 Hz. By increasing the effective area of the probe antenna, better sensitivity is obtainable over the measured range.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.3
• /
• pp.109-114
• /
• 2004

This paper proposes an advanced circuit for the fingerprint sensor signal processing. We increased the voltage between ridge and valley by modifying the parasitic capacitance eliminating circuit of sensor plate. The analog comparator was designed for comparing the sensor signal voltage with the reference signal voltage. We also propose an effective isolation strategy for removing noise and signal coupling of each sensor pixel. The fingerprint sensor circuit was designed and simulated, and the layout was performed.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.27 no.2
• /
• pp.148-154
• /
• 2017

This paper discussed design for resonance avoidance of sensor plates of loose-parts monitoring systems (LPMS) in nuclear power plants (NPP). An LPMS monitors impact of loose parts in primary loop of NPP by using accelerometers, which is mounted on sensor plates. Resonance of the plates may cause false alarms at frequencies over 10 kHz, which can be misunderstood as impact signals of loose parts with small mass and cause unnecessary response of NPP operators. Modal analysis was carried out for the existing sensor plate and design parameters affecting natural frequencies were chosen. Frequency response functions of plates were analyzed by changing the parameters and the optimized plate design for avoiding resonance was determined. Experiments was carried out for the plate specimen with improved design and verified the proposed approach and design.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2013.05a
• /
• pp.795-797
• /
• 2013

This paper describes a charge sharing capacitive-sensing circuit technique that improves the quality of images captured with fingerprint sensor LSIs. When the finger is dry, the electrical resistance of a finger surface is high. It leads to poor image quality. To capture clear images even when the finger is dry, the modified capacitive detection circuit improves the image quality using an enhancement plate at the finger surface and a voltage control circuit. The test circuit is analyzed on $0.35{\mu}m$ CMOS process.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.39 no.6
• /
• pp.1-7
• /
• 2002

The use of an asymmetric Mach-Zehnder interferometric amplitude modulator to measure a relatively low frequency electric field strength is described. The sensitivity of an electric field sensor using a Ti:LiNbO$_3$ optical modulator is strongly affected by the shape of a electrode(probe antenna). To measure the low frequency electric field, a probe antenna of wide effective area is more useful than the usual dipole antenna. As a proof of this, the optical modulator was fabricated with a plate-type probe antenna and the usefulness of this antenna tested for measuring low frequency electric field strength. Measurements were performed in the range 0.1V/cm to 60V/cm at 60Hz through 100KHz. Using a probe antenna of 10mm$\times$10mm, the output voltage of 10㎷ was measured with respect to the electric field strength of 0.1V/cm at 60Hz. By increasing the effective area of the probe antenna, better sensitivity is obtainable over the measured range.