• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2002.05a
• /
• pp.301-304
• /
• 2002

This paper describes a design and fabrication of an electronic ballast for 70［W］ceramic discharge metal halide lamps. The proposed ballast is composed of a rectifier, an active PFC, a half-bridge inverter, a LC resonant circuit and a controller. The design also includes a specially designed time circuit which provides reignition of the lamp. Running frequency of the ballast is set at 45［KHz］to avoid acoustic-resonance and flicker. from the test results, input power factor and efficiency of the ballast were estimated 91［%] and 97.7［%］, respectively.

• The korean journal of orthodontics
• /
• v.29 no.1 s.72
• /
• pp.107-112
• /
• 1999

As increasing number of adult patients, the esthetic orthodontic appliances are needed. They are tooth-colored or translucent ceramic and resin brackets. Although ceramic and resin bracket have good esthetics, there are some disadvantage such as frictions. Recently, metal-reinforced resin bracket(MRBB) were introduced. The purpose of this study is to find frictional force of MRRB, ceramic bracket and resin brackets. There is few study in frictional force about metal reinforced resin bracket(MRRB). This study used 4 orthodontic wire(.016 S-S, .0l6X.022 S-S, .016 $TMA^{\circledR}$, .0l7X.025 $TMA^{\circledR}$ and 5 brackets(one metal bracket, one ceramic bracket, one resin bracket, two MRRB). The following result is obtained using metal bracket(Ormco.Co., U.S.A), ceramic brackets($Crystalline^{\circledR}$), resin bracket( Clear Medium $Siamase^{\circledR}$). Following conclusions are obtained. 1. Ceramic and resin bracket have significantly more frictional forces than metal reinforced resin bracket and metal bracket. 2. There is no significant difference in frictional force according to the slot types of metal - reinforced resin brackets. 3. There is no significant difference in frictional force between metal reinforced resin bracket and metal bracket. 4.. Frictional force is decreased in S-S wire than TMA wire.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.999-1000
• /
• 2008

150W의 정격을 가지는 150W-CDM, HCI, CMH 세라믹 메탈 할라이드 램프의 음향공명주파수를 계산하여 예측하고 Half-Bridge구조의 Inverter로 각 램프를 점등하여 음향공명이 발생할 경우와 발생하지 않을 경우의 램프 특성을 분석한 결과 음향공명 발생시 30Hz이하의 낮은 주파수의 전류 신호가 포함됨을 확인하였다.

• The Optical Journal
• /
• s.163
• /
• pp.20-25
• /
• 2016

광학, 레이저, 통신분야 일본 최대 종합 전시회인 동경포토닉스 전시회가 지난 4월 6일부터 8일까지 도쿄 빅사이트에서 성황리에 개최되었다. Reed Exhibition Japan의 주최로 열린 이번 전시회에서는 제 16회 Phont ix 2016 이외에도 제 26회 파인테크(FineTech) 재팬, 제 7회 필름테크 재팬, 제 5회 플라스틱 재팬, 제 3회 메탈재팬, 제1회 세라믹 재팬, 일본 고기능 신소재전시회(Highly Functional Material World 2016)로 구성된 일본 최대 종합 전시회다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1993.10a
• /
• pp.161-165
• /
• 1993

최근 산업의 발달과 함께 제품의 고정도화,다양화,생산성 향상등의 요구에 의해 연삭가공에 있어서도 고능률.고정도가공이 주목되고 있다. 특히 반도체산업,광산업 등에 넓게 응용되고 있는 광학소자 가공에서는 가공정도와 가공능률이 동시에 달성되는 것에 대한 요구가 많지만, 이러한 광학소자의 가공에 있어서 기존의 연마방법은 가공정도와 가공능률에 한계가 있었다. 그런데 연삭가공에서 고능률,고정도가공의 한가지 방법으로 "전해 인프로세스드레싱(Electrolytic In-Process Dressing;ELID)연삭법"이 개발되어 고강도 메탈본드숫돌에 의한 초경합금,세라믹재료등의 경취성재료를 고품위 가공하고 있다. ELID연석법이란 숫돌의 다이아몬드나 cBN등의 연삭입자를 결합하고 있는 금속결합재를 전기분해에 의해 적당량 제거하여 일반적인 연삭과 같이 연삭입자를 연속적으로 돌출시켜 가공이 유지되도록 하는 연삭방법이다. 본 연구는 ELID연삭기술을 이용하여 원통연삭에서 철갈재료 및 세라믹재료의 고능률.고정도 가공특성을 살펴보았다. 원통연삭에서의 주철파이바본드숫돌 및 코발트본드숫돌에 의한 ELID연삭과 비트리파이드본드숫돌에 의한 일반연삭과의 고능률 가공특성을 비교하였다.

• Journal of Industrial Technology
• /
• v.28 no.B
• /
• pp.117-122
• /
• 2008

This paper presents the conductance model at high frequency of the Ceramic Metal Halide Lamp and the designing method of the electronic ballast with the LCC resonant tank type by using that model. Conductance model is based on a physical phenomenon in the discharge tube of the lamp and model constants of conductance model are obtained by Least Squares Method. After equivalent impedances are determined by the conductance model, The LCC resonance tank is designed by using the equation of the lamp power. Simulation result using PSpice software and experimental results show that the conductance model in this paper is very useful to design the electronic ballast at high frequency for the Ceramic Metal Halide Lamps.

• Journal of Energy Engineering
• /
• v.21 no.4
• /
• pp.385-392
• /
• 2012

The purpose of this study is investigated on the combustion and the thermal characteristics of porous media burners which are many using for a condensing boiler recently. In addition, results of this study will be used the fundamental information to decide the burner type which will be applied to the future development of EGR(Exhaust gas recirculation) condensing boiler. Two flat type of burners made of a the metal fiber(MF) and the ceramic(CM) were selected and examined, experimentally. As experimental results, the emitted CO concentration of CM was higher than that of MF. However, the NO concentration of MF was higher than that of CM. The efficiencies of both burners were increased as increasing the burner capacity. While the efficiency of MF was higher than that of CM, regardless of the burner capacity. In the experimental range, MF is appropriated for the burner material and 0.8 of equivalence ratio is an optimal operation condition, regarding of the proportional control, the thermal efficiency and emitted NO and CO concentration based on the regulations of KS B standard and EN 677 standard.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.10
• /
• pp.1033-1040
• /
• 2011

The premixed burner is a very strong candidate for using household boiler burner system because it has high efficiency, low emission and can be used in compact boiler system. Usually, household boiler burner systems use a Bunsen burner, which consists of an inner rich premixed flame and fuel burned completely by a secondary air supply. It has a relatively long flame length and operates in a high excess of air, so it is difficult to fit such a burner into a high efficiency compact boiler. In this paper, the characteristics of a premixed combustion burner for surface media such as metal fiber, ceramic, and SUS fin were evaluated. In particular, the flow velocity over the burner surface for the cold flow characteristics of the surface material were measured and adjusted. The combustion tests were carried out by taking pictures of the flame and measuring the flame temperature. The amounts of CO and NO were measured and the characteristics of the surface burner materials, combustion chamber, and heat exchangers were evaluated for various excess air ratios and heating values.

• Journal of the Microelectronics and Packaging Society
• /
• v.23 no.4
• /
• pp.35-41
• /
• 2016

Ceramic-metal based high power LED array package was developed via thick film LTCC technology using a glass-ceramic insulation layer and a silver conductor patterns directly printed on the aluminum heat sink substrate. The thermal resistance measurement using thermal transient tester revealed that ceramic-metal base LED package exhibited a superior heat dissipation property to compare with the previously known packaging method such as FR-4 based MCPCB. A prototype LED package sub-module with 50 watts power rating was fabricated using a ceramic-metal base chip-on-a board technology with minimized camber deformation during heat treatment by using partially covered glass-ceramic insulation layer design onto the aluminum heat spread substrate. This modified circuit design resulted in a camber-free packaging substrate and an enhanced heat transfer property compared with conventional MCPCB package. In addition, the partially covered design provided a material cost reduction compared with the fully covered one.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2002.11a
• /
• pp.159-163
• /
• 2002

So far, many kinds of researches on the chip components and MCM-C RF module especially on the 3-dimensional ceramic module using embedded passives have been performed. LTCC system has many kinds of advantages, like low loss, low cost of process, stability of process etc..The electrical behaviors of components are affected by that of the material systems including dielectrics and conductors. In this study, many kinds of conductor pastes in the variation with metal content and grain size are fabricated and their effect on the characteristics of stripline resonator are examined upto 6 ㎓.