• Applied Chemistry for Engineering
• /
• v.5 no.3
• /
• pp.385-394
• /
• 1994

Numerical solutions were obtained to the model equations for various of the parameters characterizing the pore structure, effective internal diffusion, and the chemical reaction constant. The conversion was decreased with the cause of pore closure at the surface of reacting particles, reduction of porosity, surface area of reaction and effective diffusion coefficient in the solid with the progress of reaction. Total conversion was strongly dependent on the local conversion at surface. According to the decreasing of impregnated concentration of the copper oxide and the increase of the flue gases concentration, total conversion was increased. The conversion was affected by gas flow rate and pore size distribution in the reacting solid.

• Journal of Energy Engineering
• /
• v.3 no.1
• /
• pp.18-27
• /
• 1994

석탄액화반응에서 촉매 세공구조가 촉매 불활성화에 미치는 영향을 조사하기 위하여 간단한 모델을 전개하였다. 촉매의 세공수 분포에 근거하여 두 개의 Dirac delta 함수분포를 갖는 다공질 촉매구조를 제안하였으며 촉매 세공구조와 반응속도상수와의 관계를 유도하기 위하여 단순화된 반응계를 가정하였다. 균일 코드피복 가정에서 본 모델을 촉매 불활성화 예측에 적용하였으며 계산과정에서 세공율, 세공 크기 등의 촉매 특성치에 대해서는 실제값을 이용하였다. 본 모델연구에 의하면 unimodal 촉매에 비해 bimodal 촉매가 촉매 불활성화에 덜 민감하였다.

• Magazine of the Korea Concrete Institute
• /
• v.7 no.1
• /
• pp.89-96
• /
• 1995

본 연구는 시멘트 경화체 중의 Cl 고정화 메카니즘을 규명하는 연구의 일환으로 시멘트의 C3A 함유량에 따른 Cl 고정화 효과를 세공용액 분석방법에 의해 조사한 것으로 C3A함유량 0.46 9.65%의 4가지 시멘트와 C3A를 함유하지 않은 초속경 시멘트 페이스트를 밀봉용기내에서 양생시켜 재령 28일에 세공용액을 추출하여 세공용액 중의 Cl 과 OH 농도를 측정, C3A함유량이 Cl 고정화에 미치는 영향을 검토한 것이다. 연구결과 세공용액 중의 Cl 농도는 NaCl 혼입량에 관계없이 시멘트 중의 C3A량이 증가함에 따라 낮아져 시멘트 경화체 내에서 Cl 의 고정화에 C3A가 매우 효과적임을 알 수 있었다. 세공용액의 Cl /OH 는 Cl 혼입량이 시멘트 중량의 0.3%인 경우 강재부동태막을 파괴하는 0.3보다 낮았으며 X선회절분석에 의해 C3A에 의한 고정화 메카니즘은 프리델씨염(Friedel's salt)의 생성에 의함을 확인하였다.

• Membrane Journal
• /
• v.9 no.4
• /
• pp.221-229
• /
• 1999

The nominal pore size 0.2 ${\mu}m polytetrafluroethylene(PTFE, Satorius Co,) membrane was used for the filtration of 0.1 wt% kaolin, bentonite, yeast, and starch solution, respectively. After filtration, the membrane was cleaned and the pore size was measured by liquid displacement method(LDMl using water/iso-butanol system. The pore size for new PTFE membrane evaluated by LDM was comparable with those of which were measured by mercury porosimetry and scanning electron microscope. The membrane pores were severely fouled, and constricted to below 0.3 ${\mu}m in the cases of bentonite and starch solution which contained smaller particles than pores. However, in the case of kaolin - solution, only some parts of membrane pores above 0.35 ${\mu}m were slightly fouled. Hence, the phenomena of membrane fouling could be identified quantitatively by the evaluation of pore size using LDM.

• Korean Chemical Engineering Research
• /
• v.49 no.5
• /
• pp.521-529
• /
• 2011

Methanol-to-olefin (MTO) reaction was studied over MWW zeolite with independently developed two pores (circular and straight) and MFI zeolite with intercrossed sinusoidal and straight pores in order to investigate the effect of pore structure on their catalytic behavior. MWW and MFI zeolites with similar acidity exhibited commonly high conversion and slow deactivation in the MTO reaction, but their product selectivities were considerably different: linear hydrocarbons of $C_3-C_9$ were mainly produced on MWW, while the yield of $C_2{^=}$ and aromatics were high on MFI. Polyaroamatic hydrocarbons (PAHs) were accumulated on MWW, but a small amount of benzene and aromatics on MFI. The impregnation of phosphorous on MWW caused significant decreases in the catalytic activity and toluene adsorption, but the decreases were relatively small on MFI. Although the straight pores of MWW were inactive in the MTO reaction due to the accumulation of PAHs, its circular pores which suppressed the formation of PAHs sustained catalytic activity for the production of linear hydrocarbons. Therefore, the impregnation of phosphorous on the circular pores of MWW caused a significant decrease in catalytic activity. The phosphorous impregnation on the cross sections of MFI altered the product selectivity due to the neutralization of strong acid sites, but catalytic deactivation was negligible. The difference of MWW and MFI zeolites in the MTO reaction was explained by their difference in pore structure.

• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.12
• /
• pp.2141-2148
• /
• 2000

This study is to investigate changes of pore structure with different burn-off degree of steam activated carbons manufactured from domestic anthracite. The activated carbons were characterized by adsorption of nitrogen at 77 K. Steam activation substantially enhanced the porosity of the activated carbons. Burn-off increased linearly according to increasing activation time, and total pore volume and BET surface area increased with burn-off. Activation at $800^{\circ}C$ increased more micropore volume than that at $950^{\circ}C$. Activated carbons manufactured at high temperature had less microporosity than that at lower temperature, but had more developed macroporosity. The steam activation produced an enlargement of pore below $100{\AA}$ diameter in the activated carbons. Furthermore, the porosity in the $6{\sim}40{\AA}$ pore diameters range increased considerably with the degree of burn-off.

• Membrane Journal
• /
• v.18 no.1
• /
• pp.53-64
• /
• 2008

Fouling behavior of polyethylene capillary membranes was examined by measuring the flux of bentonite colloidal suspensions through the cross flow micro filtration. The membrane fouling was due to the three mechanisms: the cake formation on the membrane surface, the standard pore blocking and the complete pore blocking by particles. These mechanisms were simultaneously responsible for the membrane fouling, being significantly governed by the cake filtration. In the total fouling at $1.0kg/cm^2$ TMP condition, the complete blocking was 3.36%, the standard blocking 3.18% and the cake filtration 96.05%. For 1000 ppm feed solution, the complete blocking was 1.71% compared with the standard blocking of 1.90% and the cake filtration of 96.39%. And 96.14% of the total fouling was generated at the initial period of filtration. The cake filtration effect was larger on $0.34{\mu}m$ pore membrane than on $0.24{\mu}m$ pore membrane. With the increase in cross flow velocity, the component fouling decreased by 10.20%, and the ratio of pore blocking to total fouling increased.

• Journal of Adhesion and Interface
• /
• v.14 no.2
• /
• pp.82-87
• /
• 2013

Preliminary studies on the synthesis of magnetic nanoparticles including nanoporous carbon materials have been done via a direct carbonization process from resol, ferric nitrate and triblock copolymer F127. The results show that the nanoporous magnetite/carbon ($Fe_3O_4$/carbon) with a low $Fe_3O_4$ content (1 wt%) possesses an ordered 2-D hexagonal (p6mm) structure, uniform nanopores (3.6 nm), high surface areas (up to 635 $m^2/g$) and pore volumes (up to 0.48 $cm^3/g$). Magnetite nanoparticles with a small particle size (10.2 nm) were confined in the matrix of amorphous carbon frameworks with superparamagnetic property (7.7 emu/g). The nanoporous magnetite/carbon showed maximum adsorption amount (995 mg/g) of ibuprofen after 24 h at room temperature. The nanoporous magnetite/carbon was separated from solution easily by using a magnet. The nanoporous magnetite/carbon material is a good adsorbent for hydrophobic organic drug molecules, i.e. ibuprofen.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2010.05a
• /
• pp.814-817
• /
• 2010

AAO thin films prepared by a two-step anodization process have pores that are uniform in diameter, highly ordered, and perfectly vertical with respect to the plane of the nano template. Further, the pore size and interpore distance can be easily controlled by varying the anodizing voltage and acid electrolyte. When metals are electrochemically deposited in the pores, metal nanowires that are highly ordered and uniform in diameter are formed in each pore.

• Applied Chemistry for Engineering
• /
• v.18 no.2
• /
• pp.99-110
• /
• 2007

Efficient and inexpensive hydrogen storage is an essential prerequisite for the utilization of hydrogen, one of the new and clean energy sources for $21^{st}$ century. In this review, several storage techniques are briefly reviewed and compared. Especially, adsorption/storage via physisorption at low temperature, by using nanoporous adsorbents, is reviewed and evaluated for further developments. The adsorption over a porous material at low temperature is currently investigated deeply to fulfill the storage target. In this review, several characteristics needed for the high hydrogen adsorption capacity are introduced. It may be summarized that following characteristics are necessary for high storage capacity over porous materials: i) high surface area and micropore volume, ii) narrow pore size, iii) strong electrostatic field, and iv) coordinatively unsaturated sites, etc. Moreover, typical results demonstrating high storage capacity over nanoporous materials are summarized. Storage capacity up to 7.5 wt% at liquid nitrogen temperature and 80 atm is reported. Competitive adsorbents that are suitable for hydrogen storage may be developed via intensive and continuous studies on design, synthesis, manufacturing and modification of nanoporous materials.