• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.31 no.6
• /
• pp.359-366
• /
• 2018

Social infrastructure facilities that have been under construction since the country's high-growth period are undergoing rapid aging, and safety assessments of large structures such as bridge tunnels, which can be directly linked to large-scale casualties in the event of an accident, are necessary. Wireless smart sensor networks that improve SHM(Structural Health Monitoring) based on existing wire sensors are difficult to construct economical and efficient system due to short signal reach. The LPWAN, Low Power Wide Area Network, is becoming popular with the Internet of Things and it is possible to construct economical and efficient SHM by applying it to structural health monitoring. This study examines the applicability of LoRa LPWAN to structural health monitoring and proposes a channel usage pre-planning based LoRa network operation method that can efficiently utilize bandwidth while resolving conflicts between channels caused by using license - exempt communication band.

• Journal of the Korea Institute of Building Construction
• /
• v.18 no.6
• /
• pp.527-532
• /
• 2018

The objective of the present study is to evaluate a practical approach for enhancing the compressive strength and minimizing deforming of aerated concrete. Test results measured in the aerated concrete mixes that were produced using 40% ground granulated blast-furnace slag (GGBS) as a replacement of cement and cured under different conditions (i.e., high temperatures of $40^{\circ}C$ and $60^{\circ}C$ for 10 hrs or 15 hrs) were compared with those obtained from the specimens cured under room temperature. No deforming was observed in the mixes with 40% GGBS. The compressive strength of the prepared aerated concrete cured under high temperature was higher than that of the concrete cured at room temperature, even at the lower ranges of the apparent dry density. However, the curing time is needed to be controlled as not exceeding 10 hrs at the temperature of $60^{\circ}C$ to prevent the decrease in the compressive strength due to foam mergences.

• Journal of IKEEE
• /
• v.23 no.2
• /
• pp.517-523
• /
• 2019

Recently, researches about automobile seat having function to support the comfort to driver and passenger during the driving are conducted in various fields including automobile seat having massage function. The effect of massage depends on the pattern of massage such as time, magnitude, and shape. In this paper, linear motor actuator, which is used as driving method in the automobile massage seat, and electromagnetic analysis method, which is used to improve the magnetic efficiency in the design of autuator, is proposed. Electromagnetic analysis using finite element method is conducted in the design of linear motor actuator. Input voltage shape for massage pattern is calculated by simulation using mathematical model of actuator. Performance test for massage pattern generation is conducted with automobile massage seat having developed actuator and controller. It is verified that developed actuator system is applicable in the automobile massage seat.

• Journal of IKEEE
• /
• v.22 no.4
• /
• pp.922-932
• /
• 2018

Radial distance sensors are widely used for surveying and autonomous navigation. It is necessary to train the operation principle of these sensors and how to apply them. Although commercialization of radial distance sensor continues to be cost-effective through lower performance, but it is still expensive for educational purposes. In this paper, we propose a distance sensor module with object tracking using radial array of low cost phototransistor which can be used for educational robot. The proposed method is able to detect the position of a fast moving object immediately by arranging the phototransistor in the range of 180 degrees and improve the sensing angle range and track the object by the sensor rotation using the servo motor. The scan speed of the proposed sensor is 50~200 times faster than the commercial distance sensor, thus it can be applied to a high performance educational mobile robot with 1ms control loop.

• The Journal of Korean Institute of Information Technology
• /
• v.16 no.11
• /
• pp.97-103
• /
• 2018

In this paper, the estimation method for the power signal harmonics is proposed by using the time-varying optimal finite impulse response (FIR) filter. To estimate the magnitude and phase-angle of the harmonic components, the time-varying optimal FIR filter is designed for the state space representation of the noisy power signal which the magnitude and phase is considered as a stochastic process. Since the time-varying optimal FIR filter used in the proposed method does not use any priori information of the initial condition and has FIR structure, the proposed method could overcome the demerits of Kalman filter based method such as poor estimation and divergence problem. Due to the FIR structure, the proposed method is more robust against to the model uncertainty than the Kalman filter. Moreover, the proposed method gives more general solution than the time-invariant optimal FIR filter based harmonic estimation method. To verify the performance and robustness of the proposed method, the proposed method is compared with time-varying Kalman filter based method through simulation.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.13 no.6
• /
• pp.1183-1190
• /
• 2018

The environmental regulations are being strengthened all over the world, and the introduction of electric vehicles are actively being considered to cope with them effectively. It is essential to establish a charging infrastructure, which is an essential element of electric vehicle distribution. In this paper, power line communication technology essential for smart charging infrastructure is studied. A control board capable of achieving a physical layer speed of 10Mbps and a TCP/IP layer of 4.5Mbps, which conforms to the ISO/IEC 15118 international standard, and a control board mounted on the board and compliant with international standards. We have developed a software solution to perform functions for linking. In addition, in order to be applied to the combo-type DC fast charger, the hardware was designed to meet the industrial environment standard and the V2G communication module was developed by integrating it with the software solution.

• Journal of the Korea Institute of Building Construction
• /
• v.19 no.1
• /
• pp.31-38
• /
• 2019

In this study, amine derivatives and ion exchange resins were selected to actively control penetration ions ($SO{_4}^{2-}$, $Cl^-$) as the element technology of repair materials for concrete structures in drainage environments. Ions ($SO{_4}^{2-}$, $Cl^-$) adsorption performance and corrosion resistance of calcium hydroxide solution with amine derivative and ion exchange resin were confirmed by ion chromatography and potentiostat analysis. As a result of the experiment, it was confirmed that the amine derivative is excellent in the adsorption of chlorine ion and the ion exchange resin is excellent in the adsorption of sulfate ion. It has been confirmed that corrosion resistance can be increased by proper combination of two materials in the calcium hydroxide solution containing sulfate ion and chloride ion simulating sewage environment.

• Korean Journal of Optics and Photonics
• /
• v.29 no.6
• /
• pp.233-240
• /
• 2018

In this paper, a design method to reduce fabrication errors in reflector shape of a test lamp for a flame detector is carried out. Although the test lamp should be operated in parallel with a high-intensity light, it is difficult to fix the small reflector that controls the central light during fabrication. To solve these problems, a small spherical reflector is designed to minimize the performance degradation for a light loss factor of less than 5%, even during tilt and decenter, and a spherical shape is proposed for a small reflector with little effect on the error when designing the optical system.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.18 no.6
• /
• pp.83-90
• /
• 2018

LoRa (Long Range) is a long-distance, low-power communication technology. Broader range of communication than NFC technology allows communication without having to install multiple APs and reduces the cost of initial infrastructure deployment. MQTT (Message, Queuing, Telemetry, Transport) protocol is also low power and lightweight protocols. It can increase module persistence and reduce maintenance costs when used with LoRa. In this paper, we developed a system for compiling various environmental information in a factory using LoRa and MQTT. Environmental sensor data from long distances can be monitored by the management system and the facilities in each workshop can be controlled. Performance tests have also shown that the use of LoRa and MQTT is effective in terms of long-distance and power consumption.

• Journal of the Korean Solar Energy Society
• /
• v.39 no.1
• /
• pp.21-32
• /
• 2019

Solar hot water system produces hot water using solar energy. If it is not used effectively, overheating occurs during the summer. Therefore, a lot of research is being done to solve this. This study develops thermoelectric power module applicable to solar hot water system. A thermoelectric material can directly convert thermal energy into electrical energy without additional power generation devices. If there is a temperature difference between high and low temperature, it generate power by Seebeck effect. The thermoelectric module generates electricity using temperature differences through the heat exchange of hot and cold water. The water used for cooling is heated and stored as hot water as it passes through the module. It can prevent overheating of Solar hot water system while producing power. The thermoelectric module consists of one absorption and two radiation part. There path is designed in the form of a water jacket. As a result, a temperature of the absorption part was $134.2^{\circ}C$ and the radiation part was $48.6^{\circ}C$. The temperature difference between the absorption and radiation was $85.6^{\circ}C$. Also, The Thermoelectric module produced about 122 W of irradiation at $708W/m^2$. At this time, power generation efficiency was 2.62% and hot water conversion efficiency was 62.46%.