• Proceedings of the KSR Conference
• /
• 2008.11b
• /
• pp.905-917
• /
• 2008

Road or Railway construction over soft ground is needed to be considered on secondary consolidation which will be caused differential settlement, lack of transport serviceability, higher maintenance cost. Especially for the railway construction in the second phase of Gyung-Bu or Ho-Nam high speed railway, concrete slab track has been adapted as a safe and cost effective geotechnical solution. In this case controlling the total settlement under the tolerance is essential. And pile supported geogrid reinforced construction method is suggested as a solution for the problem of the traditional method on soft soil treatments. Pile supported geogrid reinforced construction method consists of piles that are designed to transfer the load of the embankment through the compressible soil layer to a firm foundation. The load from the embankment must be effectively transferred to the piles to prevent punching of the piles through the embankment fill creating differential settlement at the surface of the embankment. The arrangement of the piles can create soil arching to carry the load of embankment to the piles. In order to minimize the number of piles geogrid reinforced pile supported construction method is being used on a regular basis. This method consists of one or more layers of geogrid reinforcement placed between the top of the piles and the bottom of the embankment. This paper presents several methods of pile supported geogrid reinforced construction and calculation results from the several methods and comparison of them.

• Journal of the Korean Geotechnical Society
• /
• v.21 no.2
• /
• pp.67-84
• /
• 2005

This research was conducted to evaluate the effectiveness of reinforcement for nearly saturated soft clay compaction. The effectiveness was investigated by roller compaction test using nearly saturated clay specimens. The nearly saturated condition was obtained by submerging clay in the water for 12 hours. High water content specimens were compacted in plane strain condition by a steel roller. A specimen was compacted by four 5 cm horizontal layers. Specimens were prepared fur both reinforced and unreinforced cases to evaluate the effectiveness of reinforcement. Used reinforcement is a composite consisted of both woven and non-woven geotextile. The composite usually provides drainage and tensile reinforcement to hi인 water-contented clay so that it increases bearing capacity. Therefore, large compaction load can be applied to reinforced clay and it achieves higher density effectively. The reinforcement also increases compaction efficiency because it reduces the ratio between shear and vertical forces during compaction process. The maximum vertical stress on the base of specimen usually decreased with higher compaction thickness. The reinforcement increases soil stiffness under the compaction roller and it initiates stress concentration. As a result, it maintains higher vertical stress level on the base of specimen that provides better compaction characteristics. Based on test results, it can be concluded that the reinforcement is essential to achieve effective compaction on soft clay.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.19 no.2
• /
• pp.151-159
• /
• 2015

In this study, experimental research was carried out to evaluate and improve the seismic performance of reinforced concrete beam-column joint regions using strengthening materials (CFRP sheet, AFRP sheet, embedded CFRP rod) in existing reinforced concrete structure. Therefore it was constructed and tested seven specimens retrofitting the beam-column joint regions using such retrofitting materials. Specimens, designed by retrofitting the beam-column joint regions of existing reinforced concrete structure, were showed the stable failure mode and increase of load-carrying capacity due to the effect of crack control at the times of initial loading and confinement of retrofitting materials during testing. Specimens LBCJ-CRUS, designed by the retrofitting of CFRP Rod and CFRP Sheet in reinforecd beam-column joint regions were increased its maximum load carrying capacity by 1.54 times and its energy dissipation capacity by 2.36 times in comparison with standard specimen LBCJ for a displacement ductility of 4 and 7. And Specimens LBCJ-CS, LBCJ-AF series were increased its energy dissipation capacity each by 2.04~2.34, 1.63~3.02 times in comparison with standard specimen LBCJ for a displacement ductility of 7.

• Journal of the Korean Geosynthetics Society
• /
• v.4 no.3
• /
• pp.11-19
• /
• 2005

Long-term stability of two type geogrids were evaluated. Membrane drawn type geogrid showed the exponential type tensile property and textile type geogrid showed the rapid increase of tensile property closer toward the break point. Short term accelerated creep test was done for textile type geogrid but done for membrane drawn type geogrid at ambient temperature because of its thermal property. Creep strain for membrane drawn type geogrid was larger than the ultimate tensile strain by tensile test. Reduction factor by creep deformation of textile type geogrid was smaller than that of membrane type geogrid. From this result, it was seen that the textile type geogrid is more stable than membrane type geogrid by creep deformation.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1997.10a
• /
• pp.609-614
• /
• 1997

Recently, many researchers have performed R&D about strengthening of R/C with steel plates, carbon fiber sheets. aramid fiber sheets and glass fiber sheets, and so on. However most of research were limited in study of flexural strengthening of R/C beams. This paper shows the results of an experimental study on shear reinforcement of deep beams using Glass Fiber Sheet in relation to shear-span ratio. strengthening orientation and anchorage. The results prove that shear failure is governed by reinforced orientation. adherence and anchorage. Additional anchorage of fibers does not only cause the improvement in the internal resistance, but also control the brittle shear failure of specimen after reaching the maximum load.

• Proceeding of EDISON Challenge
• /
• 2017.03a
• /
• pp.180-186
• /
• 2017

거의 모든 철근콘크리트 구조물의 보강 강재는 분할된 두개 이상의 철근으로 제작되며, 이러한 철근의 분할 부위를 평행한 두개의 철근으로 겹쳐 설치하는 것을 겹이음(Lap splice)이라고 부른다. 일반적으로 겹이음 설계는 무리없이 설계 강도를 만족시킬 뿐만 아니라 충분히 긴 수명을 가진다. 그러나 550MPa 이상의 항복 강도를 갖는 철근이나 인장 부재의 설계, 초고성능 섬유보강 콘크리트의 보강재 설계와 같은 경우, 현행 철근 겹이음 설계만으로는 그 한계가 발생한다. 따라서 현 겹이음 설계는 관련 기준의 추가와 구조적인 측면에서의 개선이 필요할 것으로 보여지며, 이를 위해 적절한 실험과 데이터 분석, 그리고 컴퓨터를 이용한 새로운 설계 모델의 개발 등의 과정이 필요할 것으로 여겨진다. 본 연구는 균질하지 않은 물성의 파괴를 다루는 RBSN(Rigid-Body-Spring Networks)을 통한 컴퓨터 시뮬레이션으로 더 효과적이고 정확한 겹이음 설계가 가능할 것으로 판단하고, 실제 모델링으로 그 가능성을 검증하였다.

• Magazine of the Korea Concrete Institute
• /
• v.6 no.1
• /
• pp.131-141
• /
• 1994

This experimental study was performed to lnvestigate the effects of the lergths dnd volume contents of glued hooked steel fiber for the fracture toughness and strength of c oncretc. The notched steel fiber reinforced concrete beams with different flber length(30, 60mm) and fiber volume content(O.0, 0.5, 1.0, 1.5, 2.0%) were tested under 3-point benclmg, md 1 he flexural strengths, fracture energy and CMOD were obtained from the experimental data. The fracture energy v~ds used as d means to evaluate the fracture toughness ot concrete. The results showed that the frdcture toughness and 5trength of conuett. were generally increased ds the content of steel fiber was inc~edsed, arid the length of steel ilber had a great efiect on the flexural strength but little on the compressive itrength and fractule toughness. And also, considering the distributions of steel fiber, workablity and the maxinium size of coarse dqgregates, the optimum content of steel fiber seemed to be about 1.0 '0, and when lts length uias longer the results were somewhat tavorable.

• Journal of the Korea Concrete Institute
• /
• v.12 no.5
• /
• pp.35-46
• /
• 2000

In this paper, an analytical model is proposed to predict the shear strenth of RC beams strengthened by FRP. This predictional model is composed of two basic models-the upper bound theorem for shear failure (shear tension or shear compression criteria) and a truss model based on the lower bound theorem for diagonal tension creteria. Also, a simple flexural theory based on USD is used to explain flexural failure. The major cause of destruction of RC beams shear strengthened by FRP does not lie in FRP fracture but in the loss of load capacity incurred by rip-off failure of shear strengthening material. Since interfacial shear stree between base concrete and the FRP is a major variable in rip-off failure mode, it is carefully analyzed to derive the shear strengthening effect of FRP. The ultimate shear strength and failure mode of RC beams, using different strengthening methods, estimated in this predictional model is then compared with the result derived from destruction experiment of RC beams shear strengthened using FRP. To verify the accuracy and consistency of the analysis, the estimated results using the predictional model are compared with various other experimental results and data from previous publications. The result of this comparative analysis showed that the estimates from the predictional model are in consistency with the experimental results. Therefore, the proposed shear strength predictional model is found to predict with relative accuracy the shear strength and failure mode of RC beams shear strengthened by FRP regardless of strengthening method variable.

• Journal of the Korean GEO-environmental Society
• /
• v.23 no.9
• /
• pp.5-16
• /
• 2022

In recent years due to the development of urban and underground space, the number of ground disasters is increasing, and it is also leading to social problems. To solve the problem, a grouting method is generally used. However, the grouting method has material (grout) limitations in permeability, gelation properties and tensile resistance. Therefore, research on grout materials mixed with fibers is actively carried out to improve the problems. However, in the actual ground injection process, many difficulties have been faced causing the blockage of the inlet port and the injection tube. In this study, 'CNT-mixed grout material' was developed using CNT powder that can reinforce the tensile strength of soils. The uniaxial compressive and tensile strength tests were performed to obtain the optimal content and mechanical properties of the CNT Powder-mixed grout. It was found that the optimal CNT powder content is 0.5% that gives the average maximum strength. A one-dimensional injection test and the bulb formation test were carried out, and it was identified that the injection rate and bulb form could be controlled by pressure and mixing ratio. Field application of the CNT-Mixed grout is simulated using numerical analysis of slopes, foundations, and tunnels reinforced in several types. The positive effect of reducing plastic ranges and settlements was confirmed.

• Journal of the Korean Geotechnical Society
• /
• v.19 no.6
• /
• pp.379-385
• /
• 2003

In the existing method to design geosynthetic reinforced embankment, the required strength of reinforcements is determined by vertical stress only rather than strain. This strength is not in accord with tensile strength that behaves as reinforcement in earth structures. The reinforcement and adjacent soil on the failure plan behave in one unit at the initial stress phase but they make a gap in strain as stress increases. This issue may cause a big impact as a critical factor on geosynthetic reinforcement design in earth structures. The quantitative analysis on strain behavior was performed with a PET Mat reinforced embankment on soft ground. From this study, several outstanding discussions are found that tensile strength of reinforcement governs the failure of embankment when the soil stress is greater than failure stress. Also the optimum required tensile strength of geosynthetic reinforcement(Tos) should be determined by stress, displacement, displacement gap and safety factor of soil-PET Mat at the location of PET Mat.