• Proceedings of the KAIS Fall Conference
• /
• 2009.05a
• /
• pp.532-535
• /
• 2009

본 논문은 초고압 전력케이블의 접속재 개발을 위한 연구결과로써, 접속시스템의 핵심기술인 고절연 고무슬리브 및 현장에서 접속 작업의 용이성을 위한 Carrier Pipe의 구조해석과 전기적 절연설계에 의한 주요부의 전기적 특성과 전계의 집중을 완화하기 위해 Simulation Tool을 이용한 수치해석 등을 실시하여 최적화된 제품을 제작하였다. 절연설계 및 전계완화 해석에서는 고절연 고무슬리브 구조에서 전계가 집중될 수 있는 중요 포인트를 벡터로 선정하였고 이를 기초로 전계해석을 진행하여 선정된 포인트들에서 전계가 집중됨을 검증하였다. 접속재의 수축거동 해석에 의하면, Carrier Pipe의 구조적 안전성을 확보하기 위하여 고절연 고무슬리브로부터의 압력을 구하여 계산한 결과 최소한 9mm이상의 Carrier Pipe 두께가 필요한 것으로 파악 되었다. 이것은 충분한 강도뿐만 아니라 Carrier Pipe의 변형발생으로 인한 현장에서의 설치문제까지 고려하게 된 값이다. 고절연 고무슬리브 제품설계 에서는 고절연 고무슬리브의 특성조건을 설정하였고 고절연 고무슬리브 제품 및 Carrier Pipe의 Interface 설계 기준을 파악하기 위하여 기존의 고절연 고무슬리브를 활용하여 Carrier Pipe와의 장착 Test를 진행하였다. 그 결과, 확장비율 110%로 적용하였을 경우는 30시간 후에는 완전 붕괴가 되었고, 붕괴가 시작되는 지점이 고절연 고무슬리브의 중앙매립전극 경계면으로써, Simulation Tool을 활용한 접속재 수축 거동 해석 결과와도 일치함을 검증 할 수 있었다.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.15 no.3
• /
• pp.219-230
• /
• 2017

This study was conducted to predict and evaluate the uncertainty of safety after closure of the second phase surface disposal facility of the Gyeongju intermediate and low level repository in Korea. In this study, four scenarios are developed considering both intact and degraded states of multi-layered covers and disposal containers; also, the fluid flow by a rainfall into the disposal facility is simulated. The rainfall conditions are implemented based on the monthly average data of the past 30 years (1985~2014); the simulation period is 300 years, the management period regulated by institutional provisions. As a result of the evaluation of the basic scenario, in which the integrity of both of the containers and the covers is maintained, it was confirmed that penetration of rainfall does not completely saturate the inside of the disposal facility. It is revealed that the multiple cover layers and concrete containers effectively play the role of barrier against the permeation of rainfall.

• Journal of Korea Foresty Energy
• /
• v.22 no.2
• /
• pp.54-59
• /
• 2003

Recently, densified pellet fuel from wood biomass is widely used at North America and Europe as a regenerable and clean carbon neutral bioenergy. High-pressure compaction of sawdust of Hyunsasi-poplar (Populus alba ${\times}$ P. glandulosa) to form a densified fuel was studied. Calorific and elemental analysis were carried out to assess Hyunsasi-poplar clones as fuels. Hot-press process was adopted for compaction of sawdust and compaction was performed under temperature from 100 to 180$^{\circ}C$, at pressure of 250 to 1000 kgf/$\textrm{cm}^2$, and for 2.5 to 10 minutes. Densified fuels were evaluated by its oven-dry density and fines after 5-minute shaking test. The target density and fines of densified fuels were over 1.2 g/$\textrm{cm}^2$ and below 0.5%, respectively. When the press-temperature is over 160$^{\circ}C$, densified fuels with density eve. 1.2 g/$\textrm{cm}^2$ and with fines below 0.5% can be produced. And the pressure over 750 kgf/$\textrm{cm}^2$ was effective for this production. It was found that the optimum press condition for preparation of densified fuel was 180$^{\circ}C$ -1000 kgf/$\textrm{cm}^2$ minutes.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.27 no.4
• /
• pp.32-42
• /
• 1990

The method using Rankine Soure distribution over the hull surface and undisturbed free surface was applied to calculate the free surface flow around a ship. The ship hull as well as a local portion of the undisturbed free surface arc geometrically represented by quadrilateral panels and the source density is determined so as to satisfy the linearized free surface condition based on the double model flow. The pressure distribution, wave resistance, wave profile and hydrodynamic sinkage force and trim moment for the Wigley hull and the Series 60 hull with $C_B=0.60$ were calculated in the fixed condition. The calculated results were compared with the measured values. The dependance of the solution on the panel arrangement, particularly on the free suraface, was also studied through 11 numerical test cases for the Wigley hull.

• Journal of the Korean Data and Information Science Society
• /
• v.26 no.6
• /
• pp.1377-1386
• /
• 2015

GDP gap is closely related with economic activity of a country as a whole, especially with the economic fluctuations which is called business cycle. GDP gap is regarded as an important variable for the monetary policy of the central bank because it provides information on the excess demand pressures and employment matters. However, GDP gap may not provide enough information of the effect of recent economic structural change or the environmental change of domestic and external economic condition. In this paper, the GDP is decomposed by statistical filtering techniques and various models are fitted to estimate the influence of GDP gap on Inflation and see if it has been changed. Analysis results show that the influence of GDP gap on inflation decreased in the 2000s while that of global GDP gap increased. These results also support that recent low inflation rate is due to the change of overseas economic condition, such as a slowdown in exports resulting from the global recession, as well as domestic factors.

• Journal of the Korean Institute of Gas
• /
• v.18 no.4
• /
• pp.56-62
• /
• 2014

The present study investigated numerically heat and mass transfer characteristics of a fixed bed reactor by using a computational fluid dynamics (CFD) code of Fluent (ver. 13.0). The temperature and species fraction were estimated for different porosities. For modeling of the catalyst in a fixed bed tube, catalysts were regarded as the porous material, and the empirical correlation of pressure drop based on the modified Eugun equation was used for simulation. In addition, the averaged porosities were taken as 0.545, 0.409, and 0.443 and compared with non-porous state. The predicted results showed that the temperature at the tube wall became higher than that estimated along the center line of tube, leading to higher hydrogen generation by the endothermic reaction and heat transfer. As the mean porosity increases, the hydrogen yield and the outlet temperature decreased because of the pressure drop inside the reformer tube.

• Journal of the Ergonomics Society of Korea
• /
• v.29 no.6
• /
• pp.875-887
• /
• 2010

The quantitative effectiveness of powered support surfaces such as APAM in preventing and treating pressure ulcers has not been sufficiently evaluated because of uncertainty of alternating pressure load input and lack of interpretation of dynamic perfusion characteristics of soft tissue. The aim was to verify the dynamic loading effects to sacral tissue perfusion characteristics from alternating set pressure changes. We developed integrated experiment system to supply alternating load to supinely positioned sacrum and concurrently measured $TcPO_2$, $TcPCO_2$ and air cell pressure. Ten aged subjects (5 female, 5 male) were tested with alternating set pressure 20, 30, 40, 50 and 60mmHg. From the dynamic perfusion response eight characteristic parameters were proposed such as average, minimum, maximum and perfusion range regarding to $TcPO_2$ and $TcPCO_2$. A one-way ANOVA was carried out to determine whether the manipulation of alternating set pressure had any effect on $TcPO_2$ and $TcPCO_2$. From the dynamic tissue perfusion response we found mean $TcPO_2$ decreased exponentially as alternating pressure load increased and perfusion range varied mainly because of minimum level change of $TcPO_2$. And perfusion range of $TcPCO_2$ affected by increase of maximum value of $TcPCO_2$. From the results we can get more strict insights about actual physiological dynamic tissue perfusion mechanism under alternating pressure load.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.820-824
• /
• 2010

The purpose of this study is to develop basic technology of hybrid rocket vehicle by constructed and launched. This small hybrid rocket using HDPE/LN2O and Aluminium steel for its body (weight : 12.5 kg, diameter : 114 mm, height : 1.8 m) was designed. The fuel grain and injector were designed for 50 kgf thrust and burning time 2.5 sec. This rocket was loaded the data acquisition device for obtaining data of pressure and velocity during its flying and equiped an automatic ejector system using spring/motor and timer to collect the rocket more safely after launching. It was launched successfully, but found some problem that the rocket's weight was heavier than expected and the thrust was not enough to reach the designed altitude and analyzed its flight path way.

• Progress in Medical Physics
• /
• v.17 no.1
• /
• pp.32-39
• /
• 2006

To assess the ability of an extravasation detection accessory (EDA) system to detect clinically important extravascular injection of iodinated contrast material delivered with an automated power injector. Fifty patients referred for contrast material enhanced body computed tomography studied in a prospective, observation study in which the EDA system was used to identify and interrupt any injection associated with clinically Important extravasation. The presence or absence of extravasation was definitively established with multi-detector CT at the injection site (injection rate, $2.0{\sim}2.5$ mL/sec). There were two true positive, extravasation volumes $22{\sim}25$ mL. The EDA system had sensitivity in the detection of clinically important extravasation. The EDA system is easy to use, safe, and accurate In the monitoring of intravenous injections for extravasation, which may prove especially useful in CT applications.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.10
• /
• pp.1061-1066
• /
• 2011

In this study, the flow characteristics of an injection nozzle installed in a high-pressure holder for improving productivity were determined. The inlet velocity, nozzle inflow angle, and nozzle outlet diameter were selected as design factors having an influence on the flow characteristics, and numerical analysis was conducted for these factors. As the inlet velocity is high and the nozzle outlet diameter is small, the pressure and velocity of the injected flow are high. In the case of the nozzle inflow angle, the variation of flow characteristics according to angle was slight, but the highest pressure and velocity were found at $15^{\circ}$. In addition, the possibility of chip elimination by the injected flow was analyzed on the basis of the numerical results.