• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.11
• /
• pp.83-94
• /
• 2003

In this paper. a highly linear and low glitch CMOS current mode digital-to-analog converter (DAC) by self calibration bias circuit is proposed. The architecture of the DAC is based on a current steering 6＋4 segmented type and new switching scheme for the current cell matrix, which reduced non-linearity error and graded error. In order to achieve a high performance DAC . novel current cell with a low spurious deglitching circuit and a new inverse thermometer decoder are proposed. The prototype DAC was implemented in a 0.35${\mu}{\textrm}{m}$ n-well CMOS technology. Experimental result show that SFDR is 60 ㏈ when sampling frequency is 32MHz and DAC output frequency is 7.92MHz. The DAC dissipates 46 mW at a 3.3 Volt single power supply and occupies a chip area of 1350${\mu}{\textrm}{m}$ ${\times}$750${\mu}{\textrm}{m}$.

• Composites Research
• /
• v.29 no.6
• /
• pp.328-335
• /
• 2016

The purpose of this study is to develop fiber reinforced cement matrix composite (ECC) produced with limestone powder in order to achieve high ductility of the composite, and to evaluate flexural performance of structural members made with ECC. Four kinds of mixture proportions were determined on the basis of the micromechanics and a steady state cracking theory considering the matrix fracture toughness and fiber-matrix interfacial characteristics. The mechanical properties of ECC, represented by strain-hardening behavior in uniaxial tension, were investigated. Also, strength property of the composite was experimentally evaluated. Two structural members made with ECC were produced and tested. Test results were compared with those of conventional concrete structural members. Increased limestone powder contents of ECC provides higher ductility of the composites while generally resulting in a lower strength property. ECC structural members exhibited higher flexural ductility, higher flexural load-carrying capacity and tighter crack width compared to conventional structural members.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.14 no.3
• /
• pp.439-452
• /
• 1994

A method to optimize the cost of R/C frames and an algorithm of the optimal limit state design for R/C frames subjected to dynamic loads are presented. The modal superposition method was used to find the dynamic responses of the frames. Each member of R/C frame is made up of more than two elements and the stiffness matrix and consistent mass matrix of three d.o.f in the node of each element was used to include axial, shear and flexural effects. The objective function to be minimized formulated the cost of materials, steel and concrete, and optimised to satisfy the behaviors of R/C frame and each constraint imposed by the limit state requirements. Both objective function and each constraint are derived in terms of design variables which include the effective depth, beam width, compression and tension steel area, and column shear steel area. A few applications are presented which demonstrate the feasibility, the validity and efficiency of the algorithm for automated optimum design of R/C frames where dynamic behavior is to be considered.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.54 no.1
• /
• pp.11-17
• /
• 2017

In this paper, an 8-direction switched beamforming antenna system at 28GHz frequency band is described for 5th generation wireless communication. This system is composed of an $8{\times}8$ Butler matrix and an 8-element patch array antenna. The antenna system switches beams in 8-direction in the wide range of ${\pm}40^{\circ}$. The antenna spacing is $0.65{\lambda}$ to achieve ${\pm}40^{\circ}$ steering range. Designed results show that the 8-direction beams are placed at ${\pm}6^{\circ}$, ${\pm}17^{\circ}$, ${\pm}28^{\circ}$, ${\pm}40^{\circ}$ offset from the center. Parasitic radiation effect from the large dimension Butler matrix need to be suppressed by employing a stripline structure.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1994.04a
• /
• pp.167-171
• /
• 1994

본 연구에서는 차폐구조 내부에 위치한 소음원의 체적이 비교적 큰 근접 음향 차폐구조로 취급하여, 구조 내부의 공간적 음장분포해석(spatial sound distribution analysis)은 하지 않고 단지 소음원의 표면과 차폐 벽면 간의 공기층에 의한 간섭 영향을 고려하면서, 차폐로 인한 음압의 상승(build up)효과를 고려하여, 직육면체의 형상을 가지는 차폐구조에 부착되는 각각의 벽면들의 음향 삽입손실(Insertion Loss, IL) 특성을 전달매트릭스 기법(Transfer Matrix Analysis, TMA)을 이용하여 해석하였으며, 이러한 벽면들에 대한 이론 해석의 결과로 제작된 벽면들의 음향차폐특성을 시험을 통해 나타내었다.

• Journal of the Korean Vacuum Society
• /
• v.19 no.1
• /
• pp.28-35
• /
• 2010

A new electrode structure in a plasma display panel was designed in a way to increase the bright room contrast ratio (BRCR). The area of the black matrix pattern to get a low reflection from the panel surface was enlarged using the new electrode design concept. The electrical characteristics such as firing voltage, voltage margin and power consumption were measured. The luminance of the panel was measured and the luminous efficiency was calculated. It was found that the new electrode structure was very effective to enhance the BRCR.

• Proceeding of KASS Symposium
• /
• 2006.05a
• /
• pp.165-169
• /
• 2006

This study presents a new stress analysis method to be substituted for the elastic analysis in such a plastic design procedure. This method is accompanied by an efficient mathematical tool which can be easily handled by personal computer. The method also easily accepts arbitrary strategies by the designer for selection member size.

• Journal of Korean Association for Spatial Structures
• /
• v.6 no.3 s.21
• /
• pp.131-137
• /
• 2006

This study presents a new stress analysis method to be substituted for the elastic analysis in such a plastic design procedure. This method is accompanied by an efficient mathematical tool which can be easily handled by personal computer. The method also easily accepts arbitrary strategies by the designer for selection member size.

• The Transactions of the Korea Information Processing Society
• /
• v.1 no.4
• /
• pp.469-478
• /
• 1994

In this paper, a high speed, high resolution information processing digital- analog converter was designed for high definition color graphic, digital image signal processing, HDTV. For high speed operation, matrix type current cell array, latch which is not use pipelined, and two dimensional structure decoder using transmission gate were designed. It is adopted to fast-conversion, low-power implementation and exhibited high performance at linearity and accuracy. To reduce silicon area and to maintain resolution, current cell array composed of weighted and non-weighted current cells. In this paper, deglitching current cell design for high accuracy, new switching algorithm assert to reduce switching error. It's This circuit dissipates 130W with a 5-V power supply, and operate above 100MHz with 10 bit resolution.

• Journal of Korean Association for Spatial Structures
• /
• v.8 no.1
• /
• pp.49-56
• /
• 2008

A multi-objective optimization approach is presented for force design of tensegrity structures. The geometry of the structure is given a priori. The design variables are the member forces, and the objective functions are the lowest eigenvalue of the tangent stiffness matrix that is to be maximized, and the deviation of the member forces from the target values that is to be minimized. The multi-objective programming problem is converted to a series of single-objective programming problems by using the constraint approach. A set of Pareto optimal solutions are generated for a tensegrity grid to demonstrate the validity of the proposed method.