• The Bulletin of The Korean Astronomical Society
• /
• v.35 no.1
• /
• pp.45.2-45.2
• /
• 2010

한국천문연구원은 한국우주전파관측망(Korean VLBI Network, KVN)에서 시험 운영 중인 한일공동VLBI상관기(Korea-Japan VLBI Correlator, KJJVC)의 핵심인 VLBI상관 서브시스템(VLBI Correlation Subsystem, VCS)을 제어하기 위해 CCS(Correlation Control Software)를 개발하였다. CCS는 명령어의 문법 검사를 하고, VCS와 TCP/IP 소켓으로 통신하여 명령어와 응답(reply)을 주고받으며, VCS의 실시간 요청에 대응하여 입력 지연 파라미터(delay parameter)를 자동으로 전달하는 소프트웨어이다. CCS는 사용자의 명령어를 local UNX FIFO를 통하여, 명령줄(Command Line)로 전달받고, 이러한 명령어들의 조합을 쉘 스크립트로 묶는 형태로 구성 되어있다. 그러나, 이렇게 명령어의 조합을 직접 편집하여 구성할 때, 입력할 명령어나 지연 파라미터의 구성이 복잡해지면, 스크립트에 필요한 명령이 문법에 맞지 않게 사용되거나, 일부 명령어가 누락될 수 있는 위험이 있다. 이러한 오류를 차단하고 작업 효율을 높이기 위하여, 상관 처리의 전체 운용 및 제어를 통합적으로 할 수 있는 사용자 인터페이스가 필요하다. 이를 위하여 KJJVC의 운용 및 제어를 위한 GUI를 설계하고 제작하였다. 개발된 GUI는 Python 언어를 기반으로 하는 wxPython 패키지를 사용하였으며, 사용자(Operator)가 명령어 문법이나 순서를 확인할 필요 없이, 관측 정보와 관측국 정보, 기록 매체 정보만 가지고 손쉽게 명령어의 조합을 생성해 주며, 시스템 초기화와 각종 정보의 입력이 직관적으로 이루어질 수 있도록 해 준다. 본 연구에서는 개발된 GUI의 설계 및 개발 과정과 시험운영에 대해 소개한다.

• Journal of the Institute of Convergence Signal Processing
• /
• v.9 no.3
• /
• pp.213-218
• /
• 2008

This paper describes hardware-based high speed multimedia data reassembly processor for remote multimedia Set-Top-Box(MSTB) of interactive satellite multimedia communication system. The conventional multimedia data reassembly scheme is based on software processing of MSTB. As increasing of transmission rate for multimedia data services, the CPU load of remote MSTB is increased and reassembly performance of MSTB is limited. To provide high speed multimedia data service to end user, we proposed hardware based high speed multimedia data reassembly processor. It is implemented by using an FPGA, a PCI interface chip, and RAMs. And it is integrated in MSTB and tested. It has been confirmed to meet required all functions and processing rate up to 116Mbps.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.8 no.5
• /
• pp.53-58
• /
• 2008

This study presented a design model optimizing a distance of inlet with drainage pipe laid under the gutter in road. When the distance of inlet changed, a basin for the gutter divided by the distance of inlet and the inflow coming into the gutter would be changed. In this case, the change of inlet distance causes the change of a diameter of drainage pipe and slope because of the change of capacity. Therefore, the optimization is needed to design the combination of them for the distance of inlet. Genetic Algorithm is used to determine the optimal combination of them. The conditions of road and the precipitation were assumed like a real and the range of inlet distance adopted $10{\sim}30\;m$ which has been introduced in domestic. This model presented the optimal distance of inlet and the combination of pipe and slope through the minimum cost. The result of the study is that the optimal distance of inlet is different from each slope of road and it can reduce about 20% of total cost for the distance of inlet.

• Proceedings of the Korean Information Science Society Conference
• /
• 2012.06b
• /
• pp.178-180
• /
• 2012

협업은 둘 이상의 사람들이 하나의 업무 또는 목적을 달성하기위해 공동으로 협력하여 일하는 것이다. 최근 개인 및 조직 간 협업 범위가 공동분석, 데이터 연계, 서비스 조합 등으로 확장되고 대용량 데이터 공유 및 실시간 연계분석 활동이 증대되면서 협업 지향적인 시스템 설계와 개발이 중요시 되고 있다. 특히 스마트워크와 지능화된 협업 기반은 데이터, 프로세스, 서비스, 사람 간의 다차원 연계와 실시간 활용, 의미 기반의 기계적 협력을 전재로 하고 있다. 본 연구에서는 Data, Process, Service, People 측면의 4가지 계층으로 전사적 자원을 설계하고 메타 메타데이터 기반의 온톨로지 분석을 통해 자원 간의 연계와 조합을 지원하는 시스템을 설계했다. Data 계층은 프로세스별 Input, Output 정보를 식별하여 Data의 메타 정보를 정의하고 이를 검색 에이전트가 색인하여 모델링에 참조할수록 한다. Process 계층은 BPMN모델을 확장한 exCPM의 개선 모델을 바탕으로 프로세스를 수행주체 간, 정보공유측면에서 프로세스를 분석했다. Service 계층은 협업지향적인 프로세스를 구성하는 컴포넌트를 서비스로 인식하고 프로파일을 통해 협업을 위한 검색과 프로세스를 연계지원하도록 설계 했다. 마지막으로 People계층은 자원, 프로세스, 서비스 등 시스템에 관여하는 참여자들의 메타정보를 정의하고 이를 온톨로지 기반의 모델에 통합하여 자동 검색되도록 설계했다. 이를 통해 프로세스와 서비스 측면에서 협업을 요구하는 에이전트와 일반 검색 사용자들이 프로세스 간 협업 자원을 파악하고 상호 관계를 분석할 수 있도록 하는 한편, 프로세스를 지원하는 컴포넌트와 서비스 간의 자동적인 조합을 통해 통합적 자원 협력과 실시간 협업 지원 기반을 제시했다.

• Journal of KIISE:Software and Applications
• /
• v.35 no.2
• /
• pp.91-104
• /
• 2008

Service-Oriented Computing (SOC) is the development method that published services are selected and composed at runtime to deliver the expected functionality to service clients. SOC should get maximum benefits not only supporting business agility but also reducing the development time. Services are selected and composed at runtime to improve the benefits. However, current programming language, SOC platforms, business process modeling language, and tools support either manual selection or static binding of published services. There is a limitation on reconfiguring and redeploying the business process to deliver the expected services to each client. Therefore, dynamic selection is needed for composing appropriate services to service clients in a quick and flexible manner. In this paper, we propose Dynamic Selection Handler (DSH) on ESB. we present a design method of Dynamic Selection Handler which consists of four components; Invocation Listener, Service Selector, Service Binder and Interface Transformer. We apply appropriate design patterns for each component to maximize reusability of components. Finally, we describe a case study that shows the feasibility of DSH on ESB.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.11
• /
• pp.56-64
• /
• 2007

We developed the first automatic design system targeting a promising hybrid CMOS-Nanoelectronics Architecture called CMOL. The CMOL architecture uses NOR gates to implement combinational logic. In this hybrid CMOS-nanoelectronics architecture, logical functions and the interconnections share the nanoelectronics hardware resource. Towards automating the CMOL physical design process, we developed a model for the CMOL architecture, formulated the placement and routing problems for the CMOL architecture subject to the unique CMOL specific constraints, and solved it by combining a placement algorithm with a gate assignment algorithm in a loop. We validated the proposed approach by implementing several industrial strength designs.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.15 no.2
• /
• pp.219-235
• /
• 2002

This paper deals with parametric studies of the structural response of underground LNG storage tanks according to change in design conditions. In the design of underground LNG storage tank, it is requited to determine the optimal tank shape and dimension to represent a more improved structural behavior under many loading conditions and load combinations. Consequently, main factors which affect to the structural response of LNG storage tanks from planning and design up to maintenance, are investigated, and the differences in structural behavior due to those factors are analyzed. On the basis of the obtained results item parametric studies, a guideline for a more reasonable design is introduced.

• Tunnel and Underground Space
• /
• v.11 no.2
• /
• pp.96-108
• /
• 2001

A concrete lining of NATM tunnel is the final product of a process that involves planning and evaluation of user needs, geotechnical investigations, analysis of ground-lining interaction, construction, and observations and modifications during construction. The designer must consider the lining in context of the many function, construction, and geotechnical requirements. Also, the loss of supporting capacity of shotcrete lining due to poor rock qualities and shotcrete erosion must be considered. The values, shapes, and estimating methods of rock load and water pressure are very different with every designers. Estimating methods of rock loads used in the design of NATM tunnel concrete lining are investigated. Structural analyses are done in various load combinations, and the member forces(moment, axial force and shear force) are compared. The adequate load combination of rock load and water pressure is proposed.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.5
• /
• pp.1990-1995
• /
• 2012

This paper presents design methodology to determine the design parameters that affect the manufacture of aluminum forging piston using the FE simulation and the Taguchi method. Maximum forging load is used as the objective function, and preform, material temperature and draft angle are selected as the design parameters. Their combinations are implemented by orthogonal array, and forging load is evaluated through the simulation. From the analytic results of design parameters to minimize the load using signal to noise ratio, their optimal combinations are proposed. The proposed design methodology will be able to help in selecting proper preform among preforms and to be used in determining the optimal combination of the parameters in metal forming process.

• The KIPS Transactions:PartD
• /
• v.12D no.6 s.102
• /
• pp.889-898
• /
• 2005

Recently, one of the most challenging problems is to compose web services dynamically, that is, on demand. A number of researchers have been considerably interested in the dynamic web services composition. However, while most of them focused on the semi-automatic web services composition with a human controller, very little attention was devoted to the full automation of this process. This paper primarily focuses on the automatic web services composition techniques. The main idea is to implement an automatic web services composition system using web ontologies to realize the semantic web and workflow technologies to play a major role in E-businesses. In this paper, we propose a matching algorithm for web service discovery and present an approach based on the use of ontologies to facilitate the interoperability of web services. Finally, we describe a workflow execution plan to support the automatic web services composition, and an experimental study that shows the high performance of our system.