• Journal of the Korea Concrete Institute
• /
• v.24 no.3
• /
• pp.275-283
• /
• 2012

Steel Plate for Rebar Connection was recently developed to splice rebars in delayed slab-wall joints in high-rise building, slurry wall-slab joints, temporary openings, etc. It consists of several couplers and a thin steel plate with shear key. Cyclic loading tests on slab-wall joints were conducted to verify structural behavior of the joints having Steel Plate for Rebar Connection. For comparison, joints with Rebend Connection and without splices were also tested. The joints with Steel Plate for Rebar Connection showed typical flexural behavior in the sequence of tension re-bar yielding, sufficient flexural deformation, crushing of compression concrete, and compression rebar buckling. However, the joints with Rebend Connection had more bond cracks in slabs faces and spalling in side cover-concrete, even though elastic behavior of the joints was similar to that of the joints with Steel Plate for Re-bar Connection. Consequently, the joints with Rebend Connection had less strengths and deformation capacities than the joints with Steel Plate for Re-bar Connection. In addition, stiffness of the joints with Rebend Connection degraded more rapidly than the other joints as cyclic loads were applied. This may be caused by low elastic modulus of re-straightened rebars and restraightening of kinked bar. For two types of diameters (13mm and 16mm) and two types of grades (SD300 and SD400) of rebars, the joints with Steel Plate for Rebar Connection had higher strength than nominal strength calculated from actual material properties. On the contrary, strengths of the joints with Rebend Connection decreased as bar diameter increased and as grade becames higher. Therefore, Rebend Connection should be used with caution in design and construction.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.39 no.2
• /
• pp.40-51
• /
• 2011

Recently, the public's interest in quality of life and good design has increased, and the opportunities for their participation in space planning and the design process are expanding. However, the public still lacks understanding of the role(and importance) of space and environment and is not experienced in expressing their opinion on improving the urban environment. At this point, 'Built Environment Education for Kids' will be the key to understanding space and environment as future citizens and to developing the ability of problem-solving and expressing their opinions. This study aims to change the awareness of the public as well as experts, and to make a better urban space through comparison and analysis of domestic and foreign 'Built Environment Education.' In 27 countries around the world(more than 110 institutions), 'Built Environment Education' from childhood is being implemented. Such movements aim to make people participate in the space design and decision-making process by understanding a fundamental element of the built environment and space perception. In this study, the United States, Britain, Finland, Japan and South Korea's 'Built Environment Education' are discussed Above all, the definition, range and target of 'Built Environment Education' are discussed For each case, the purpose and effect, laws and educational processes, systems and roles, and examples of programs are analyzed. Through reviewing each attribute and their implications, a conclusion is drawn on the aspects we have to consider in laying the foundation for implementing the 'Built Environment Education' in Korea, such as consideration of the locality, organizing systematic networks and composing a pool of experts, building proper institutions, and establishing the role of the government. This case study of 'Built Environment Education' can help increase the awareness of the public and build their strength in establishing a better future space. Through the analysis of the purpose, laws, systems, and contents, this case study is expected to provide and build the foundation for an educational system and develop an appropriate program that best suits our society.

• Korean Chemical Engineering Research
• /
• v.46 no.5
• /
• pp.994-1001
• /
• 2008

Freundlich isothermal adsorption parameters, applicable to such biofilter-model as process-lumping model(Lim's model), for sterilized granular activated carbon(GAC), sterilized compost and sterilized equal volume mixture of GAC and compost were obtained and were compared each other, assuming that adsorbents are enclosed by water layer, in order to construct robust process-lumping biofilter model effective for wide-range of hydrophilic volatile organic compounds(VOC). In this investigation 0.04, 0.08, 0.12, 0.16, 0.2, 0.4, 0.8 and 1.0ml of ethanol were added to three kinds of adsorbent-media and were placed at $30^{\circ}{\cdots}$ under the wet condition of the media, which was the same as biofilter operating condition, until the adsorption reached the condition of equilibrium before each adsorbed amount of ethanol was obtained. Then adsorption capacity parameters(K) and adsorption exponents of Freundlich adsorption isotherm equation, which simulates the adsorbed amount of ethanol equilibrated with the ethanol concentration of the condensed water in the pore of the media, were constructed for sterilized granular activated carbon(GAC), sterilized compost and sterilized equal volume mixture of GAC and compost as (0.7566 and $5.070{\times}10^{-7}mg-ethanol/mgmedia/(mg-ethanol/m^3)^{0.7566}$), (0.8827 and $1.000{\times}10^{-8}mg-ethanol/mgmedia/(mg-ethanol/m^3)^{0.8827}$) and (0.5688 and $5.243{\times}10^{-6}mg-ethanol/mgmedia/(mg-ethanol/m^3)^{0.5688}$), respectively. These Freundlich isothermal adsorption parameters were applicable to the adsorption characteristics of biofilter media enclosed with bio-layer. The order of magnitude of the ratio of ethanol-air/water partition coefficient and toluene-air/water partition coefficient was almost consistent to that of ethanol-adsorbed amounts in this experiment with compost and in the investigation of Delhomenie et al. on toluene-adsorption to wet compost.

• Journal of the Korea Society of Computer and Information
• /
• v.16 no.7
• /
• pp.1-11
• /
• 2011

Many researchers have studied on the methods to improve the processor performance. However, high integrated semiconductor technology for improving the processor performance causes many problems such as battery life, high power density, hotspot, etc. Especially, as hotspot has critical impact on the reliability of chip, thermal problems should be considered together with performance and power consumption when designing high-performance processors. To alleviate the thermal problems of processors, there have been various researches. In the past, mechanical cooling methods have been used to control the temperature of processors. However, up-to-date microprocessors causes severe thermal problems, resulting in increased cooling cost. Therefore, recent studies have focused on architecture-level thermal-aware design techniques than mechanical cooling methods. Even though architecture-level thermal-aware design techniques are efficient for reducing the temperature of processors, they cause performance degradation inevitably. Therefore, if the mechanical cooling methods can manage the thermal problems of processors efficiently, the performance can be improved by reducing the performance degradation due to architecture-level thermal-aware design techniques such as dynamic thermal management. In this paper, we analyze the cooling efficiency of high-performance multicore processors according to mechanical cooling methods. According to our experiments using air cooler and liquid cooler, the liquid cooler consumes more power than the air cooler whereas it reduces the temperature more efficiently. Especially, the cost for reducing $1^{\circ}C$ is varied by the environments. Therefore, if the mechanical cooling methods can be used appropriately, the temperature of high-performance processors can be managed more efficiently.

• Food Science and Preservation
• /
• v.14 no.4
• /
• pp.414-418
• /
• 2007

The physicochemical characteristics and sensory properties of Deodeok wine, formed by leaching of Deodeok at room temperature for 180 days, were investigated over the following range of Deodeok levels: 10, 15 and 20% (all w/v). The higher the level of Deodeok, the greater were the final values of total sugars, reducing sugars, total polyphenols, and crude saponins. The Hunter's b-value (yellowness) of Deodeok wine varied markedly with Deodeok levels, and yellowness was highest in Deodeok wine containing 20% (w/v) Deodeok. Non-volatile compounds, that form the basis of the liquor tax law, were 0.64, 1.38 and 2.11% (all w/v), respectively, at day 160. Of these values, that of 2.11% (w/v), the level of non-volatile compounds in Deodeok wine containing 20% (w/v) Deodeok, was in accord with the liquor tax law (that requires this figure to be 2.0%). Sensory evaluation showed that Deodeok wine containing 20% (w/v) Deodeok was superior to the other wines tested.

• Korean Journal of Agricultural Science
• /
• v.10 no.1
• /
• pp.129-134
• /
• 1983

Importance has been increased on farming mechanization in harvesting, handling and processing of forage in Korea. Small grasslands are most spread and popular in Korea in comparison with those of Europe and America. Therefore shearing characteristics of some major forage crops should be studied to be contributed to the basic data to develop a moderate size forage harvester being suitable to the small grassland. They were studied on six kinds of forage crops - reed canarygrass, alfalfa, red clover, orchardgrass, meadow fescue and birdsfoot trefoil-in regarding with moisture content levels and shearing angles. The results were as follows; 1. The increase rate of the linear density in relation to the diameter was greater in red clover than other kinds, and order of increase rate in greatness was reed canarygrass, alfalfa and meadow fescue. 2. The increase rates of the maximum shear forces were high in relation to their cross - sectional area in alfalfa and birdsfoot trefoil with hard stems, and the shear energy were comparatively large in orchardgrass and meadow fescue with soft stems, also reed canarygrass and red clover had high values in both the maximum shear force and the shear energy. 3. The shear energy per unit area or shear strength in relation to moisture content showed concave curves with the minimum values at about 70%w. b. which was in the beginning stage of drying in meadow fescue and orchardgrass, nevertheless reed canarygrass and red clover had convex curves with the maximum values at about 40%w.b. 4. The shear force in relation to the shear angle decreased generally with decrease of shear angle from $90^{\circ}$ to $70^{\circ}$ or $50^{\circ}$.

• The Journal of Korean Academy of Prosthodontics
• /
• v.47 no.2
• /
• pp.125-135
• /
• 2009

Statement of problem: Loosening or fracture of the abutment screw is one of the common problems related to the dental implant. Generally, in order to make the screw joint stable, the preload generated by tightening torque needs to be increased within the elastic limit of the screw. However, additional tensile forces can produce the plastic deformation of abutment screw when functional loads are superimposed on preload stresses, and they can elicit loosening or fracture of the abutment screw. Therefore, it is necessary to find the optimum tightening torque that maximizes a fatigue life and simultaneously offer a reasonable degree of protection against loosening. Purpose: The purpose of this study was to present the influence of tightening torque on the implant-abutment screw joint stability with the 3 dimensional finite element analysis. Material and methods: In this study, the finite element model of the implant system with external butt joint connection was designed and verified by comparison with additional theoretical and experimental results. Four different amount of tightening torques(10, 20, 30 and 40 Ncm) and the external loading(250 N, $30^{\circ}$) were applied to the model, and the equivalent stress distributions and the gap distances were calculated according to each tightening torque and the result was analyzed. Results: Within the limitation of this study, the following results were drawn; 1) There was the proportional relation between the tightening torque and the preload. 2) In case of applying only the tightening torque, the maximum stress was found at the screw neck. 3) The maximum stress was also shown at the screw neck under the external loading condition. However in case of applying 10 Ncm tightening torque, it was found at the undersurface of the screw head. 4) The joint opening was observed under the external loading in case of applying 10 Ncm and 20 Ncm of tightening torque. 5) When the tightening torque was applied at 40 Ncm, under the external loading the maximum stress exceeded the allowable stress value of the titanium alloy. Conclusion: Implant abutment screw must have a proper tightening torque that will be able to maintain joint stability of fixture and abutment.

• Journal of The Korean Association For Science Education
• /
• v.37 no.5
• /
• pp.825-833
• /
• 2017

The Korean Ministry of Education has emphasized human resource development with creative and convergent ability for future science and technology development. Korean STEAM Education aims to enhance students' interest and their understanding of science and technology as well as to develop students' creative problem-solving skills. Through STEAM R&E project, students experience self-directed research in order to solve the problem in the context of everyday life. In this study, we aim to find out whether the creative leader competency of high school students changed after they experienced the STEAM R&E project. The creative leader competency consisted of three domains: cognitive, affective, and societal domain. We measured the creative leader competency using the questionnaire scales. The questionnaire was administered to 612 high school students who participated in the 2016 STEAM R&E project. Pre- and post- test scores were collected, and we analyzed it. We compared the mean difference between pre- and post- test scores as well as the mean differences among science high school, gifted school, science core school, and general high school. From the result, we found that all student' creative leader competency improved after participating in the STEAM R&E project in all three domains. The result also showed that students' test scores of science high school and gifted school showed no significant mean differences, while student's scores of both science core school and general high school improved significantly. From the results, we concluded that STEAM R&E activities could be an effective tool in cultivating creative leader competency, especially for general high school students and science core school students. We also suggested that further researches are needed to find how we could enhance students' creative leader competency.

• Korea journal of population studies
• /
• v.30 no.2
• /
• pp.71-95
• /
• 2007

This paper attempts to identify the principle of family succession and family patterns of yangban in the late Chosun period through an analysis of male adaptation cases found in family registration records. The primary source of analysis is the family registration documents of Uiseong Kim's from the late 17th century to the early 20th century. As a result, it is found that there is a substantial change in the patterns of family from the early and mid Chosun period to the late Chosun period. The change is the strengthening of the principle of patriarchy succession through male adoption. Looking at the data as a whole, the average number of household members is increased and the membership of kinship also expanded. In contrast to the family patterns of the early Chosun period, not only the patterns of Uiseong Kim's family are predominately immediate family or collateral family but also the majority is extended family in the 18th and 19th centuries. The male adoption cases recorded in Uiseong Kim's family registration documents take up 33.8% of the male adoption cases in the entire family registration documents. This goes to show that the strengthening of the principle of primogeniture succession at a time when child mortality rate is very high resulted in the increase of male adoption. In conclusion, the late Chosun society was a society where the seat of primogeniture was much more important than immediate hereditary members in the family succession.

• Journal of the Korea Concrete Institute
• /
• v.14 no.1
• /
• pp.126-135
• /
• 2002

Plate bonding technique has been widely used in strengthening of existing concrete structures, although it has often a serious problem of premature falure such as interface separation and rip-off. However, this premature failure problem has not been well explored yet especially in view of local failure mechanism around the interface of plate ends. The purpose of the present study is, therefore, to identify the local failure of strengthened plates and to derive a separation criterion at the interface of plates. To this end, a comprehensive experimental program has been set up. The double lap pull-out tests considering pure shear force and half beam tests considering combined flexure-shear force were performed. The main experimental parameters include plate thickness, adhesive thickness, and plate end arrangement. The strains along the longitudinal direction of steel plates have been measured and the shear stress were calculated from those measures strains. The effects of plate thickness, bonded length, and plate end treatment have been also clarified from the present test results. Nonlinear finite element analysis has been performed and compared with test results. The Interface properties are also modeled to present the separation failure behavior of strengthened members. The cracking patterns as well as maximum failure loads agree well with test data. The relation between maximum shear and normal stresses at the interface has been derived to propose a separation failure criterion of strengthened members. The present study allows more realistic analysis and design of externally strengthened flexural member with steel plates.