• Journal of Biomedical Engineering Research
• /
• v.25 no.5
• /
• pp.343-349
• /
• 2004

Electroglottograph(EGG) is a signal recorded from the vocal cord vibration by measuring electrical impedance across the vocal folds through the neck skin. The purpose of this study was to develop EGG system and to evaluate possibility for the application on speech analysis and laryngeal disease diagnosis. EGG system was composed of two pairs of ring electrodes, tuned amplifier, phase sensitive detector, low pass filter, and auto-gain controller. It was designed to extract electric impedance after detecting by amplitude modulation method with 2.7MHz carrier signal. Extracted signals were transmitted through line-in of PC sound card, sampled and quantized. Closed Quotient(CQ), Speed Quotient(SQ), Speed Index(SI), fundamental frequency of vocal cord vibration(F0), pitch variability of vocal fold vibration (Jitter), and peak-to-peak amplitude variability of vocal fold vibration(Shimmer) were analyzed as EGG parameters. Experimental results were as follows: the faster vocal fold vibration, the higher values in CQ parameter and the lower values in SQ and SI parameters. EGG and speech signals had the same fundamental frequency. CQ, SQ, and SI were significantly different between normal subjects and patients with laryngeal cancer. These results suggest that it is possible to implement portable EGG system to monitor the function of vocal cord and to test functional changes of the glottis.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.24-24
• /
• 2010

대형구조물의 구조안정성 진단, 로봇과 같은 지능기계의 제어, 환경오염을 감지하기 위한 센서의 중요성은 날로 증대되고 있다. 이러한 센서의 감도와 성능을 높이기 위해서 소형화, 다기능화, 집적화가 요구되고 있는데, 고성능 센서소자들의 집적화를 위해서 기존에 적용된 벌크형태의 재료들을 박막화하여 다층적층 및 소형화할 필요가 있다. 집적화 센서의 구현에 있어서 전극박막은 센서의 특성을 좌우하는 중요한 역할을 한다. 일반적으로 금속박막이 전극으로 사용되고 있으나 열적 불안정성 및 박리현상의 문제점을 지니고 있다. 따라서 이를 해결하기 위해 전도성산화막을 전극으로 적용하고자하는 연구가 요구되고 있다. 전도성산화막을 전극으로 적용하면 센서소자의 성능이 개선되는 경향이 있다. $Sr_2FeMoO_6$(SFMO) 산화물은 자기장을 인가했을 때 저항이 감소하는 CMR(colossal magnetoresistance) 물질이며 상온비저항이 낮은 것으로 알려져 있다. 이중 페롭스카이트 (double perovskite) 구조를 갖는 $Sr_2FeMoO_6$ 박막은 센서소자의 전극으로 적용 가능할 것으로 생각되어 박막을 제조하고자 하였으며 미세구조와 전기전도 특성을 조사하였다. 박막제조를 위해서는 RF 스퍼터법을 사용하였다. 스퍼터를 위한 타겟은 고상반응법으로 분말타겟을 제조하였다. Ar/$O_2$ 가스 유랑변화, 압력변화, 기판 온도변화가 박막의 상형성 등 박막특성에 미치는 영향을 조사하였다. 기판으로는 $SiO_2$(100nm)/Si 기판을 사용하였다. 증착직후에는 비정질막이 얻어졌으며 SFMO 상을 만들기 위해서는 후열처리가 필요하였는데, 환원성 가스 분위기 [$H_2$(5%)/Ar] 에서 열처리 조건을 최적화하여 이중 페롭스카이트 구조의 단일상 박막을 제조할 수 있었다. SFMO 단일상 박막은 증착시에나 후열처리 시 산소의 억제가 중요함을 알 수 있었다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.30 no.7
• /
• pp.447-453
• /
• 2017

In this study, $Li_2MnSiO_4$ cathode material and LiPON solid electrolyte were manufactured into thin films, and the possibility of their use in thin-film batteries was researched. When the RTP treatment was performed after $Li_2MnSiO_4$ cathode thin-film deposition on the SUS substrate by a sputtering method, a ${\beta}-Li_2MnSiO_4$ cathode thin film was successfully manufactured. The LiPON solid electrolyte was prepared by a reactive sputtering method using a $Li_3PO_4$ target and $N_2$ gas, and a homogeneous and flat thin film was deposited on a $Li_2MnSiO_4$ cathode thin film. In order to evaluate the electrochemical properties of the $Li_2MnSiO_4$ cathode thin films, coin cells using only a liquid electrolyte were prepared and the charge/discharge test was conducted. As a result, the amorphous thin film of RTP treated at $600^{\circ}C$ showed the highest initial discharge capacity of about $60{\mu}Ah/cm^2$. In cases of coin cells using liquid/solid double electrolyte, the discharge capacities of the $Li_2MnSiO_4$ cathode thin films were comparable to those without solid LiPON electrolyte. It was revealed that $Li_2MnSiO_4$ cathode thin films with LiPON solid electrolyte were applicable in thin film batteries.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.91-91
• /
• 1999

광소자 기술은 정보 전달 및 저장 기술의 지속적인 증가 요구에 따라 발전을 거듭하여 왔다. 특히 광통신 및 저장 기술에서 광원으로 사용되는 레이저 다이오드는 안정되면서 쉽게 제작할 수 있어야 한다. 이온 주입 방법은 반도체 공정에서 광범위하게 사용되는 공정이며 이미 소자측면에서 안정성이 확보되었다고 볼 수 있으나 대부분 메모리 등의 실리콘 반도체에서 이용되어 왔다. 최근에는 화합물 반도체 분야에서도 적용하는 예가 증가되고 있으나 광원으로 사용되는 레이저 다이오드의 경우는 우수한 품질의 반도체 층이 요구되며 따라서 damage가 큰 이온 주입 방법을 이용한 연구는 아직 많이 이루어져 있지 않다. 본 연구에서는 레이저 다이오드 구조의 성장측에 국부적으로 Fe 이온을 주입하여 도파로를 형성하여 광을 구속하여 도파시키는 동시에 전기적으로도 도파로 부분으로만 다이오드가 형성되도록 하고자 한다. 먼저 p층의 전기적 절연에 필요한 조건을 확보하기 위하여 CBE를 사용하여 Fe가 doping 된 SI-InP wafer 위에 p-InP (Be:5x1017 cm-3)층을 1.2$mu extrm{m}$ 성장한 후 ohmic 층으로 p-InGaAs (Be:1x1019 cm-3)을 0.1$\mu\textrm{m}$ 성장한 시료에 고에너지 이온 주입 장치를 사용하여 Fe 이온을 1MeV, 1.6meV의 에너지에 각각 1x1014cm-2, 2x1014cm-2 의 dose로 전면에 implant 하였다. 이 시료를 tube furnace에서 500, 600, $700^{\circ}C$각각 10분씩 annealing 한 후 재성장을 확인하기 위하여 DCXRD을 측정하였다. 그림 1은 DCXRD rocking curve로 annealing 하기 전 후의 In rich에서 side peak의 감소를 확인 할 수 있었는데 이는 damage가 어느 정도 복구되었음을 의미한다. 또한 절연 특성을 확인하기 위하여 ohmic metal을 증착하여 Hall 효과를 측정하였다. 그림 2에 보이는 것과 같이 annealing 온도가 증가함에 따라 면저항이 크게 증가함을 볼 수 있으며 이온 주입하기 전의 시료에 비해 104 이상의 저항을 갖을 수 있다. 향후 이러한 결과를 바탕으로 1.55$\mu\textrm{m}$ LD 구조에서 발진 특성을 관찰할 계획이다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.8
• /
• pp.602-610
• /
• 2012

The powders for the $Na_xWO_3$ (x= 1 and 0.75) sputtering targets were synthesized by the calcination in reductive atmosphere. Near single-phase $NaWO_3$ and single-phase $Na_{0.75}WO_3$ powder targets were prepared. By using the targets, thin films of each composition were deposited by rf magnetron sputtering on the $SiO_2$ (100 nm)/Si substrates and annealed by RTP (rapid thermal processing) for crystallization. In the case of the $NaWO_3$ composition, single-phase $Na_xWO_3$ thin films, where x was believed to be slightly less than 1, were fabricated accompanying the Na-diffusion into the substrates during RTP. However, in the case of the $Na_{0.75}WO_3$ thin film preparation, it was unable to make single-phase thin films. From the phase formation behaviors of both powders and thin films, it was revealed that $Na_xWO_3$ with nonstoichiometric composition of x, which was slightly less than 1, was favorable. The good electrical conduction properties were obtained from the single-phase $Na_xWO_3$ thin films. Their electrical resistivities were as low as $7.5{\times}10^{-4}{\Omega}{\cdot}cm$.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.14 no.4
• /
• pp.1-7
• /
• 2000

In this paper, we study a cause of malfunction of switch to control drive motor in DFMS(Digital Flux Mapping System) which can measure incore neutron flux of the nuclear plant, and develope a method to solve this problem. DFMS has the type of generating contact signal by mechanical switch lever, which is operated whenever thimble detector inserted or withdrawed through thimble Guide Tube. However the characteristics of the lever tend to be changed by mechanical degrade or bad environment and the lever finally generates errotic contact signal. Therefore we installed electric coil ass'yin the outside of Guide Tube instead of mechanical switch assy's. In addition we applied resonance effect to control circuit and installed condenser in the input of power supply to protect noise and interference. After completion of this improvement, we tested this improved device repetitively under the various conditions. In conclusion, we identified the generation of the desired contact signal and the prevention of detector failure through plant surveillance test during normal plant operation.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.11
• /
• pp.1631-1636
• /
• 2010

In this study, we demonstrate a nano-scale lithograph obtained on localized (100) silicon (p-type) surface using by modified AFM (Atomic force microscope) apparatuses and by adopting controlling methods. AFM-based experimental apparatuses are connected to a customized pulse generator that supplies electricity between the conductive tip and the silicon surface, while maintaining a constant humidity throughout the lithography process. The pulse durations are controlled according to various experimental conditions. The electrochemical reaction induced by the pulses occurs in the gap between the conductive tip and silicon surface and result in the formation of nanoscale oxide particles. Oxide particles with various heights and widths can be created by AFM surface modification; the size of the oxide particle depends on the pulse durations and the applied electrical conditions under a humid environment.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.951-952
• /
• 2007

International Electrotechnical Commission (IEC)은 국제 규격을 제 개정하는 단체로서, 1906년에 설립된 조직이다. 2006년 말 기준으로 67개국의 회원 국가를 보유하고 있으며 총 5,613개의 규격을 제 개정하고 있다. IEC는 많은 수의 규격을 제 개정하기 위하여 100개의 Technical Committee (TC)와, 각 TC 산하에 Subcommittees(SC)를 두고 있다. SC는 다시 산하에 Working group(WG)을 두어 실제적으로 해당 국제규격의 제 개정은 바로 이 WG에서 작업을 하게 된다. 본 논문에서는 IEC TC17내의 SC17B와 SC17D의 구성, 현황 및 활동과 현재 진행되고 있는 저압차단기의 규격동향에 대하여 고찰하였다. IEC TC17은 차단기, 개폐기(스위치), 단로기, 버스관로 및 배전반등과 관련된 IEC 규격의 제 개정을 담당하고 있다. TC17 산하의 SC17B는 저압 차단기, SC17D는 저압배전반제품과 관련된 규격을 관리하고 있다. 한국은 SC17B와 SC 17D의 P-member(Participant)로서 투표권을 갖고 있으며, 한국전기연구원이 운영간사를 맡고 있다. 현재 국내기업체 전문가와 연구원들의 의견을 수렴하여 국가의견으로서 IEC에 제출하고 있지만 앞으로 더 많은 전문가들의 참여가 시급한 실정이다.

• The Journal of the Acoustical Society of Korea
• /
• v.28 no.8
• /
• pp.815-821
• /
• 2009

Information processing in variable and noisy environments is usually accomplished by means of adaptive filters. Among various adaptive algorithms, Least Mean Square (LMS) has become the most popular for its robustness, good tracking capabilities and simplicity, both in terms of computational load and easiness of implementation. In practical application of the LMS algorithm, the most important key parameter is the Step Size. As is well known, if the Step Size is large, the convergence rate of the algorithm will be rapid, but the steady state mean square error (MSE) will increase. On the other hand, if the Step Size is small, the steady state MSE will be small, but the convergence rate will be slow. Many researches have been proposed to alleviate this drawback by using a variable Step Size. In this paper, a new variable Step Size LMS(VSSLMS) called Categorized VSSLMS (CVSSLMS) is proposed. CVSSLMS updates the Step Size by categorizing the current status of the gradient, hence significantly improves the convergence rate. The performance of the proposed algorithm was verified from the view point of convergence rate, Excessive Mean Square Error(EMSE), and complexity through experiments.

• Culinary science and hospitality research
• /
• v.21 no.3
• /
• pp.248-258
• /
• 2015

Jungkwa is traditional food in Korea and difficult to prepare. This study proposes to use a rice cooker to simplify the process of preparing ginseng jungkwa. The following is the summary of the study. This study examined low calorie sweeteners (xylitol, oligosaccharide, stevioside, erythritol) instead of sugar for ginseng jungkwa to satisfy customers' health needs. After adding sugar, xylitol, oligosaccharide, stevioside, and erythritol to ginseng jungkwa, moisture and sugar content were measured. Based on the results, the ginseng jungkwa made with xylitol had a low moisture content, but it had the highest sugar content. The ginseng jungkwa with xylitol had average sweetness equal to that of sugar. In addition, L-values were highest with stevioside whereas the b-values and a-values were highest with sugar. Hardness and springiness were highest in the ginseng jungkwa added with sugar while adhesiveness was highest in the ginseng jungkwa added with oligosaccharide. In a sensory evaluation, the appearance, flavor, taste, texture, and overall preference were highest for the oligosaccharide added ginseng jungkwa. In the end, the best low calorie sweetener for rice cooker prepared ginseng jungkwa proved to be oligosaccharide.