• Transactions of the Korean hydrogen and new energy society
• /
• v.27 no.5
• /
• pp.503-509
• /
• 2016

Fuel cell is a device for producing electricity by using the hydrogen produced by the fuel processor. At this time, CO is also created by the fuel processor. The resulting CO enters the stack where is produce electricity and leads to the adsorption of anode catalyst, finally the CO poisoning occurs. Stack which occurred CO poisoning has a reduction in performance and shelf life are gradually fall because they do not respond to hydrogen. In this paper, experiments that using a PROX reactor to prevent CO poisoning were carried out for removing the CO concentration to less than 10ppm range available in the fuel cell. Furthermore experiments by the PROX reaction was designed and manufactured with a water-cooling heat exchange reactor to maintain a suitable temperature control due to the strong exothermic reaction.

• Applied Chemistry for Engineering
• /
• v.9 no.4
• /
• pp.497-503
• /
• 1998

The catalytic oxidation of 1.2-dichloroethane was investigated over precious metal supported on alumina using a fixed bed microreactor. Among the catalysts tested, the conversion of 1.2-dichloroethane decreased in the following order : Ru > Pt > Pd $${\sim_=}$$ Rh and Pt was found to be the most active catalyst for the complete oxidation of 1.2-dichloroethane to $CO_2$. Major products containing carbon were vinyl chloride and $Co_2$ at temperature ranging from 200 to $400^{\circ}C$. The presence of vinyl chloride in products suggests that the first step in the oxidation of 1.2-dichloroethane is dehydrochlorination and the second is oxidation of vinyl chloride to $CO_2$. To investigate the effect of HCl on the activity of the complete oxidation, some experiments were conducted by adding HCl to the feed. The presence of HCl increased the conversion of 1.2-dichloroethane below $300^{\circ}C$ owing to the increase of surface acidity, but it didn't affect the conversion above $300^{\circ}C$. The reversible adsorption of HCl onto catalyst surface inhibited the complete oxidation to $CO_2$.

• Applied Chemistry for Engineering
• /
• v.16 no.5
• /
• pp.641-647
• /
• 2005

The partial oxidation of methane is one of important processes for hydrogen production. As a membrane reactor, palladium-silver (Pd-Ag) alloy membrane prepared by electroless plating technique was employed for partial oxidation of methane. The experimental variables were reaction temperature, $O_2/CH_4$ mole ratio, $CH_4$ feed rate, and $N_2$ sweep gas flow rate. The methane conversions increased with the reaction temperatures in the range of 350 to $730^{\circ}C$. The highest methane conversion and CO selectivity were obtained at the condition of $O_2/CH_4$ mole ratio of 0.5 and $730^{\circ}C$ using commercially available nickel/alumina catalyst. The Pd-Ag membrane reactor showed higher methane conversions, 10~40% higher, compared to those in a traditional reactor.

• Korean Chemical Engineering Research
• /
• v.50 no.5
• /
• pp.885-889
• /
• 2012

In this study, amine and metal oxide additives were investigated to improve $CO_2$ adsorption capacity of activated carbons (ACs). The characteristics of surface modified ACs were studied by X-ray photoelectron spectroscopy (XPS), $N_2$ adsorption, X-ray diffraction (XRD), and BET. Amine surface treatment decreased specific surface area and pore volume of ACs, but increased alkalinity by the incorporated nitrogen functional groups. Adsorption capacities of amine functionalized ACs was larger than original ACs, because basic group which can react with $CO_2$ was grafted on the ACs surface. Presence of copper oxides on ACs also enhances the carbon dioxide adsorption. The copper oxides could increase the adsorption rate of carbon dioxides due to the acid-base interaction (or electron acceptor-donor interaction). It was found that copper oxide loading was a promising method to improve the $CO_2$ adsorption capacity of ACs.

• Journal of Korean Society of Environmental Engineers
• /
• v.28 no.4
• /
• pp.368-375
• /
• 2006

Single and complex metal oxide catalysts supported onto a commercial DT51D $TiO_2$ have been investigated for gas-phase TCE oxidation in a continuous flow type fixed-bed reaction system to develop a better design approach to catalysts for this reaction. Among the $TiO_2$-supported single metal oxides used, i.e., $CrO_x,\;FeO_x,\;MnO_x,\;LaO_x,\;CoO_x,\;NiO_x,\;CeO_x\;and\;CuO_x$, with the respective metal contents of 5 wt.%, the $CrO_x/TiO_2$ catalyst was shown to be most active for the oxidative TCE decomposition, depending significantly on amounts of $CrO_x\;on\;TiO_2$. The use of high $CrO_x$ loadings greater than 10 wt.% caused lower activity in the catalytic TCE oxidation, which is probably due to production of $Cr_2O_3$ crystallites on the surface of $TiO_2$. $CrO_x/TiO_2$-supported $CrO_x$-based bimetallic oxide catalysts were of particular interest in removal efficiency for this TCE oxidation reaction at reaction temperatures above $200^{\circ}C$, compared to that obtained with $CrO_x$-free complex metal oxides and a 10 wt.% $CrO_x/TiO_2$ catalyst. Catalytic activity of 5 wt.% $CrO_x-5$ wt.% $LaO_x$ in the removal reaction was similar to or slightly higher than that acquired for the $CrO_x$-only catalyst. Similar observation was revealed for 5 wt.% $CrO_x$-based bimetallic oxides consisting of either 5 wt.% $MnO_x,\;CoO_x,\;NiO_x\;or\;FeO_x$. These results represent that such $CrO_x$-based bimetallic systems for the catalytic TCE oxidation on significantly minimize the usage of $CrO_x$ that is well known to be one of very toxic heavy metals, and offer a very useful technique to design new type catalysts for reducing chlorinated volatile organic substances.

• Clean Technology
• /
• v.20 no.3
• /
• pp.330-336
• /
• 2014

Mg-Al mixed oxides with molar ratio of Mg/Al = 1-3 were prepared by co-precipitation and characterized by using X-ray diffraction, scanning electron microscopy, BET surface area and pore volume measured by $N_2$ sorption analysis, and temperature programmed desorption of iso-propanol. As Al content in Mg-Al mixed oxide increased, the acidity and BET surface area proportionally increased. This increase of acidity directly influenced the catalytic activity of iso-propanol conversion and selectivity to propylene.

• Applied Chemistry for Engineering
• /
• v.17 no.4
• /
• pp.414-419
• /
• 2006

Effects of water vapor, hydrocarbons, and CO, which are inevitably included in exhaust gases of combustion, on a combined $De-NO_{x}$ process of non-thermal plasma and $NH_{3}$ SCR (Selective Catalytic Reduction) have been investigated. Test results showed that fast SCR reaction enhanced $De-NO_{x}$ rate under the low temperature conditions, $150{\sim}200^{\circ}C$ The present test, however, showed that the role of the fast SCR reaction can be significantly suppressed by addition of hydrocarbons in a non-thermal plasma reactor. Detailed investigation verified that such suppressed role of the fast SCR reaction could be caused by the $NO_{2}/NO_{x}$ ratio modified by aldehydes produced from hydrocarbons in a non-thermal plasma reactor. In addition, the present study was confirmed that the effects of water vapor and CO were not noticeable compared with the hydrocarbon effects.

• Korean Chemical Engineering Research
• /
• v.53 no.3
• /
• pp.391-396
• /
• 2015

To investigate the effect of the catalyst synthesis method on the oxidative dehydrogenation (ODH) of nbutenes, $BiFe_{0.65}MoP_{0.1}$ oxide catalysts were prepared with various synthesis methods such as co-precipitation, citric acid method, hydrothermal method, and surfactant templated method. The catalysts were characterized by X-ray Diffraction (XRD), $N_2$ sorption, and $NH_3/1$-butene-temperature programmed desorption ($NH_3/1$-butene-TPD) to correlate with catalytic activity in ODH reaction. Among the catalysts studied here, $BiFe_{0.65}MoP_{0.1}$ oxide catalyst prepared with co-precipitation method marked the highest activity showing 1-butene conversion, 79.5%, butadiene selectivity, 85.1% and yield, 67.7% after reaction for 14 h. From the result of $NH_3$-TPD, the catalytic activity is closely related to the acidity of the $BiFe_{0.65}MoP_{0.1}$-x oxide catalyst and acidity of the $BiFe_{0.65}MoP_{0.1}$ oxde catalyst prepared with co-precipitation method was higher than that of other catalysts. In addition, combined with the 1-butene TPD, the higher catalytic activity is closely related to the amount of weakly adsorbed intermediate (< $200^{\circ}C$) and the desorbing temperature of strongly adsorbed intermediates (> $200^{\circ}C$).

• Transactions of the Korean hydrogen and new energy society
• /
• v.17 no.3
• /
• pp.293-300
• /
• 2006

KIER has been developing a Ru-based preferential oxidation catalysts and a novel fuel processing system to provide hydrogen rich gas to residential PEMFCs system. The catalytic activity of Ru-based catalysts was investigated at different Ru loading amount and different support structure. The obtained result indicated that 2 wt% loaded Ru-based catalyst supported on ${\alpha}-Al_2O_3$ showed high activity in low temperature range and suppressed the methanation reaction. The developed prototype fuel processor showed thermal efficiency of 78% as a HHV basis with methane conversion of 92%. CO concentration below 10 ppm in the produced gas is achieved with separate preferential oxidation unit under the condition of $[O_2]/[CO]=2.0$. The partial load operation have been carried out to test the performance of fuel processor from 40% to 80% load, showing stable methane conversion and CO concentration below 10 ppm. The durability test for the daily start-stop and 8 h operation procedure is under investigation and shows no deterioration of its performance after 50 start-stop cycles. In addition to the system design and development.

• Clean Technology
• /
• v.20 no.3
• /
• pp.269-276
• /
• 2014

This study was aimed to develop catalytic system for the dry-based reduction of oxidized mercury ($Hg^{2+}$) to elemental mercury ($Hg^0$) which is one of the most important components comprising mercury continuous emission monitoring system (Hg-CEMS). Based on the standard potential in oxidation-reduction reaction, transition metals including Fe, Cu, Ni and Co were selected as possible candidates for catalyst proceeding spontaneous reduction of $Hg^{2+}$ into $Hg^0$. These transition metal catalysts revealed high activity for reduction of $Hg^{2+}$ into $Hg^0$ in the absence of oxygen in reactant gases. However, their activities were greatly decreased in the presence of oxygen, which was attributed to the transformation of transition metals by oxygen to the corresponding transition metal oxides with less catalytic activity for the reduction of oxidized mercury. Hydrogen supplied to the reactant gases significantly enhanced $Hg^{2+}$ reduction activity even in the presence of oxygen. It might be due to occurrence of combustion reaction between $H_2$ and $O_2$ causing the consumption of $O_2$ at such high reaction temperature at which oxidized mercury reduction reaction took place. Because the system showed high activity for $Hg^{2+}$ reduction to $Hg^0$, which was compatible to that of wet-chemistry technology using $SnCl_2$ solution, the catalytic reduction system of Fe catalyst with the supply of $H_2$ could be employed as a commercial system for the reduction of oxidized mercury to elemental mercury.