• Journal of the Society of Naval Architects of Korea
• /
• v.30 no.2
• /
• pp.66-75
• /
• 1993

Flow control devices, such as flow liners, are frequently introduced hi a cavitation tunnel in order to reduce the tunnel blockage effect, when a three-dimensional wake distribution is simulated using a complete ship model or a dummy model. In order to estimate the tunnel wall effect and to evaluate the effect of flow liners on the simulated wake distribution, a surface panel method is adopted for the calculation of the flow around a ship model and flow liners installed in a rectangular test section of a cavitation tunnel. Calculation results on the Sydney Express ship model show that the tunnel wall effect on the hull surface pressure distribution is negligible for less than 5% blockage and can be appreciable for more than 20% blockage. The flow liners accelerate the flow near the after body of the ship model, so that the pressure gradient there becomes more favorable and accordingly the boundary layer thickness would be reduced. Since the resulting wake distribution is assumed to resemble the full scale wake, flow liners can also be used to simulate an estimated full scale wake without modifying the ship model. Boundary layer calculation should be incorporated in order to correlate the calculated wake distribution with tole measured one.

• Proceeding of EDISON Challenge
• /
• 2016.03a
• /
• pp.582-587
• /
• 2016

연료효율에 대한 선주들의 요구와 그린쉽이라는 사회적 흐름에 맞춰 현재 연료 절감 장치에 대한 연구가 활발히 진행되고 있다. 본 연구에서는 KVLCC2M의 반류개선 및 연료효율 증가를 위한 반원형 덕트의 변수 연구를 진행하였으며, 계산의 신뢰도를 검증하기 위해 서울대학교 선박저항성능 연구실에서 실시한 모형 시험결과와 비교하였다. 반원형 덕트의 크기와 길이방향 위치를 설계변수로 설정하여, 총 12가지 경우에 대한 CFD 계산을 시행하였으며, 계산 결과를 유동 정류를 통한 저항 감소와 반류 개선을 통한 프로펠러의 성능 개선 이라는 두 가지 기준으로 최적 조건을 선정하였다. 또한, 후처리를 통해 계산 결과를 추가적으로 분석하여 에너지 절감의 이론적인 배경을 찾았으며, 이를 바탕으로 반원형 덕트를 개선하여 부채꼴형 덕트를 새로이 설계하였다. 이에 대한 추가적인 계산 결과 최대 4%의 연료절감 효과를 최종 확인하였다.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.17 no.2
• /
• pp.154-159
• /
• 2007

Wake distribution data of stem flow fields have been accumulated systematically by model tests. If the correlation between geometrical hull information and wake distribution is grasped through the accumulated data, this correlation can be helpful to designing similar ships. In this paper, Neuro-Fuzzy system that is emerging as a new knowledge over a wide range of fields nowadays is tried to estimate the wake distribution on the propeller plan. Neuro-Fuzzy system is well known as one of prospective and representative analysis method for prediction, classification, diagnosis of real complicated world problem, and it is widely applied even in the engineering fields. For this study three-dimensional stern hull forms and nominal wake values from a model test ate structured as processing elements of input and output layer, respectively. The proposed method is proved as an useful technique in ship design by comparing measured wake distribution with predicted wake distribution.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.27 no.7
• /
• pp.1106-1115
• /
• 2021

In this study, a fin that controls ship stern flow was attached on stern hull of a 80k bulk carrier to improve resistance performance. The rectangular cross-sectional fin was attached at several locations on the hull, and angle to streamline was changed with constant length, breadth, and thickness. The resistance performance and wake on propeller plane of the hull with and without the fin were analyzed using model-scale computational fluid dynamics simulation. The analysis results were extrapolated to full-scale to compare the performance and wake of the full-scale ship. First, the fin changed path of bilge vortex that flowed into the propeller along the stern hull without the fin to transom stern. This change increased pressure of the stern hull and upper region of the propeller, so pressure resistance and total resistance of the hull were reduced - the nearer the fin location to after perpendicular (AP) and base line of the hull, the larger the reduction of the resistances. Second, nominal wake fraction of the hull with the fin was lower than that without the fin. This dif erence was in proportion to the angle of the fin, but the total resistance reduction was in proportion until a certain angle at which the reduction was maximum. The largest total resistance reduction was approximately 2.1% at 12.5% of length between perpendiculars from the AP, 10% of draft from the base line, and 14° with respect to the streamline.

• Journal of the Society of Naval Architects of Korea
• /
• v.54 no.6
• /
• pp.515-521
• /
• 2017

Large Cavitation Tunnel (LCT) of KRISO enables us to conduct cavitation tests of the propeller attached to a ship model. As the ship model tests are done at rather high Reynolds number of 107~108, flow measurement system such as pitot tube cannot be employed because of structural safety problems in its system and difficulties in installing it within the test section. Thus, KRISO has developed new 3-D LDV system used in large test section of LCT. There are several difficulties in using 3-D LDV, which did not allow efficient operation of it. The first trouble was the calibration using the conventional pin hole. To make the focus with same laser-beam waists at the wanted position, the high spatial resolution CCD is utilized in the calibration procedure for 3-D LDV. The off-axis configuration provides two velocity components in the horizontal plane and on-axis configuration gives third velocity component in the vertical plane. The horizontal velocity components are also obtained in the coincidence mode, which prevents any misleading results in the off-axis configuration. The nominal wake of Aframax tanker model is measured by the developed 3-D LDV system. The measured hull wake showed good agreement with that obtained by CFD calculation.

• Journal of the Society of Naval Architects of Korea
• /
• v.48 no.2
• /
• pp.128-133
• /
• 2011

In the present study, the flow fields in between the propeller and the semi-spade rudder are investigated by using PIV technique to find out the influences of both simulated hull wake and propeller wake on the incident flow to the rudder. The velocity fields are measured at the propeller rotation angle of $180^{\circ}$ and the rudder deflection angles of $0^{\circ}$. Flow fields measured at each rudder deflection angle are analyzed in terms of angle-of-attack against the rudder leading edge. The hull wake increases the angle-of-attack more than that in the uniform inflow condition, forming the angle-of-attack of about $20^{\circ}$ at 0.7R(R=propeller radius) position. The distribution of the angle-of-attack is strongly affected by the stagnation point around the leading edge and camber effect of the rudder. These effects provide asymmetric distribution of angle-of-attack with respect to the leading edge of the rudder.

• Journal of the Society of Naval Architects of Korea
• /
• v.58 no.1
• /
• pp.10-16
• /
• 2021

This paper systematically investigates and correlates pressure fluctuation and nominal wake characteristics according to the angle of the vortex generators by introducing the angle adjustment method of the Vortex Generator (VG). The vortex generators are installed at the port and starboard of a model ship. The vortex generator performance test is executed on a model ship installed in the Large Cavitation Tunnel (LCT) and the angle of VG is freely controlled by a servo motor. The systematic test results for the vortex generator show that the well-designed VG is an effective appendage for reducing the pressure fluctuation level and shows the direction of VG's angular design optimization.

• Journal of the Society of Naval Architects of Korea
• /
• v.40 no.5
• /
• pp.26-35
• /
• 2003

Propellers operating in a given nonuniform ship wake generate unsteady loads leading to undesirable stern vibration problems. The skew is known to be the most proper and effective geometric parameter to control or reduce the fluctuating forces on the shaft. This paper assumes the skew profile as either a quadratic or a cubic function of the radius and determines the coefficients of the polynomial function by applying the simplex method. The method uses the converted unconstrained algorithm to solve the constrained minimization problem of 6-component shaft excitation forces. The propeller excitation was computed either by applying the two-dimensional gust theory for quick estimation or by the fully three-dimensional unsteady lifting surface theory in time domain for an accurate solution. A sample result demonstrates that the shaft forces can be further reduced through optimization from the original design.

• Journal of the Society of Naval Architects of Korea
• /
• v.34 no.1
• /
• pp.1-10
• /
• 1997

Viscous flow around actual ship is calculated by an use of RANS equations. The propriety of this computing method, usefulness to hull form design and the scale effect which is the effect of viscous flow depending on the scale of ship model are investigated. Reynolds stress is modelled by using k-${\varepsilon}$ turbulence model and the law of wall is applied near the body. Body fitted coordinates are introduced for the treatment of the arbitrary 3-dimensional shape of the ship hull form. The transformed equations in the computational domain are numerically solved by an employment of FVM. In the calculation of pressure, SIMPLE method is adopted and the solution of the discretized equation is obtained by the line-by-line method with the use of TDMA The calculations of two ships, 4410 TEU container carrier and 50,000 DWT class bulk carrier, are performed at model and actual ship scale. The results are compared and discussed with the model test results which are viscous resistance, nominal wake distribution at propeller plane and limiting streamline on the hull surface. They describe the effect of stem form and the scale effect very well. In particular, the calculated nominal wake distribution and limiting streamline are agreed qualitatively with the experiments and the viscous resistance values are estimated within ${\pm}5%$ difference from the resistance tests.

• Journal of the Society of Naval Architects of Korea
• /
• v.29 no.4
• /
• pp.132-145
• /
• 1992

A series of design, theoretical analysis and model test procedures is presented for the development of an axisymmetric stator-propeller system. A preswirl stator is located in front of a propeller in order to improve the propulsion efficiency by cancellation of the slip stream rotational velocity due to the propeller. Model test results show that propulsion efficiency gain due to the symmetric stator-propeller system is about 3% compared to the single propeller. This efficiency gain would increase for full scale application since the pressure drag coefficient of the stator would decrease due to increasement of turbulent intensity behind the hull wake and increasement of Reynolds number.