• Microbiology and Biotechnology Letters
• /
• v.40 no.4
• /
• pp.339-347
• /
• 2012

Viral safety is an important prerequisite for clinical preparations of mammalian cell culture-derived biopharmaceuticals, because numerous adventitious viruses have been contaminated during the manufacturing process. In particular, Chinese hamster ovary (CHO) cells are highly susceptible to several RNA viruses including reovirus (Reo), bovine viral diarrhea virus (BVDV), and bovine parainfluenza virus (BPIV) and there have been reports of such viral contaminations. Therefore, viral detection during the CHO cell process is necessary to ensure the safety of biopharmaceuticals against viruses. In this study, a multiplex reverse transcription (RT)-PCR assay was developed and subsequently evaluated for its effectiveness as a means to simultaneously detect Reo, BVDV, and BPIV during the manufacture of cell culture-derived biopharmaceuticals. Specific primers for Reo, BVDV, and BPIV were selected, and a multiplex RT-PCR was optimized. The sensitivity of the assay for simultaneous amplification of all viral target RNAs was $7.76{\times}10^2\;TCID_{50}/ml$ for Reo, $7.44{\times}10^1\;TCID_{50}/ml$ for BVDV, and $6.75{\times}10^1\;TCID_{50}/ml$ for BPIV. The multiplex RT-PCR was proven to be very specific to Reo, BVDV, and BPIV and was subsequently applied to the validation of CHO cells artificially infected with each virus. It could detect each viral RNA from CHO cells as well as culture supernatants. Therefore, it was concluded that the multiplex RT-PCR assay can be applied to detection of the adventitious viruses during the manufacture of cell culture-derived biopharmaceuticals.

• Korean Chemical Engineering Research
• /
• v.52 no.1
• /
• pp.119-125
• /
• 2014

This study evaluated the environmental impacts of a soil washing (SW) process, especially, we compared the on-site and off-site remediation of TPH-contaminated soil using green and sustainable remediation (GSR) tool. To assess relative contribution of each stage on environmental footprints in the entire soil washing process, we classified the process into four major stages: site foundation (stage I), excavation (stage II), separation & washing (stage III), and wastewater treatment (stage IV). In on-site SW process, the relative contribution of $CO_2$ emissions and energy consumption were 87.1% and 80.4%, respectively in stage I, and in off-site SW process, the relative contribution of $CO_2$ emissions and energy consumption were 82.7% and 80.5%, respectively in stage II. In conclusion, the major factor contributing environmental impact in the SW process were consumable materials including steel and stainless steel for washing equipment in on-site treatment and fuel consumption for transportation of soil in off-site treatment.

• Korean Journal of Mineralogy and Petrology
• /
• v.33 no.1
• /
• pp.41-51
• /
• 2020

The purpose of this study was to investigate the possibility of eco-friendly/efficient recovery of valuable resources, such as Au from mine tailings, which are environmental pollutants in the Mongolian mine sector. For this purpose, this study selected 4 place of mine tailings of the Mongolian mines sector and carried out mineralogy evaluation of the valuable resources in the tailings. In this study, flotation was performed to separate and concentrate valuable resources in the tailings. Microwave nitric acid leaching was used to leach the valuable resources contained in the sample and to improve the Au grade. Chloride leaching attempted to leach Au from the leaching residues. XRD analysis of the tailings samples showed that most of the samples consisted of silicate minerals. As a result of confirming the content of the element through XRF analysis, the SiO₂ content was very high, the Fe₂O₃ content was 2.32-4.23%, and the content of PbO, CuO and ZnO components were all within 2%. As a result of flotation for the tailings samples, the recovery of Au was the highest in Bayanairag sample (95.38%). As a result of microwave nitric solution experiment on Au concentrate sample obtained by flotation, the content of Au in the microwave nitrate leaching residue increased by 12.15% from 192.72 g/ton to 216.14g/ton in Khamo sample, the highest increase was 57.58% in Bayanairag sample. TCLP tests on tailings generated after flotation showed dissolution characteristics within EPA. Chloride leaching test was performed to recover Au from solid residues. The leaching rate was 87.43-89.35% within 10 minutes. For Khamo sample, 100% Au was leached after 60 minutes of leaching time. Therefore, in order to process the tailings continuously generated in Mongolia, applying the same process as the present study is expected to effectively recover the valuable resources contained in the tailings.

• Economic and Environmental Geology
• /
• v.45 no.2
• /
• pp.121-135
• /
• 2012

Soil dispersion and heavy metal leaching with two heavy metal-contaminated soils were studied to derive the optimal dispersion condition in the course of developing the remedial technology using magnetic separation. The dispersion solutions of pyrophosphate, hexametaphosphate, orthophosphate and sodium dodecylsulfate (SDS) at 1 - 200 mM and the pH of solutions was adjusted to be 9 - 12 with NaOH. The clay content of suspension as an indicator of dispersion rate and the heavy metal concentration of the solution were tested at the different pHs and concentrations of the dispersion solution during the experiment. The dispersion rate increased with increasing the pH and dispersion agent concentration of the solution. The dispersion efficiency of the agents showed as follows: pyrophosphate > hexametaphosphate > SDS > orthophosphate. Arsenic leaching was sharply increased at 50 mM of phosphates and 100 mM of SDS. The adsorption of $OH^-$, phosphates and dodecysulfate on the surface of Fe- and Mn-oxides and soil organic matter and the broken edge of clay mineral might decrease the surface charge and might increase the repulsion force among soil particles. The competition between arsenic and $OH^-$, phosphates and dodecylsulfate for the adsorption site of soil particles might induce the arsenic leaching. The dispersion and heavy metal leaching data indicate that pH 11 and 10 mM pyrophosphate is the optimum dispersion solution for maximizing dispersion and minimizing heavy metal leaching.

• Resources Recycling
• /
• v.22 no.5
• /
• pp.43-49
• /
• 2013

Froth flotation was performed to remove As from the tailing of Sangdong Mine. When the tailings of Sangdong Mine were analyzed by the Standard Method for the Soil Environment Conservation, the concentration of As was found to be at a serious level (282 mg/kg), exceeding countermeasure standard (75 mg/kg). Froth flotation was performed to remove As and preliminary tests were performed to select the reagents. Specifically, froth flotation was performed using collector and frother, KAX and DF250 respectively. An experiment based on pH changes found that the removal rate was highest at pH6. The removal rate of As was highest at agitating rate 1500 according to the agitating rate. In the experiment based on the quantities of KAX added, the removal rate of As was found to be highest at 300 g/ton and was reduced at higher levels than 300 g/ton. An experiment based on pulp density found that the removal rate was highest at pulp density 30%. It was possible to adjust the As level -- which exceeded countermeasure standard (75 mg/kg) -- to 22.5mg/kg to satisfy the Warning standard (25 mg/kg), from the results of froth flotation.

• Resources Recycling
• /
• v.12 no.3
• /
• pp.3-12
• /
• 2003

Physical separation containing grinding, sieving, dry magnetic separation and air classification were carried out in order to recover Ta anode from waste Ta condenser. Roll crusher wat used for the liberation of resin and metals in closed circuit system. The liberation between Ta anode and resin was easily achieved, whereat some of metals did not liberated from the Ta anode when the waste condenser was crushed below 8 mesh. When the crushed sample were divided into 8/10 mesh, 10/18 mesh and -18 mesh, metals was mainly remained in 8/10 mesh in contrast to Ta anode was in +18 mesh. It was shown that resin was more easily crushed rather than metals from the result of that resin content was 71.5％ in -18 mesh. The liberation efficiency was different with the input size of the crushed sample and average efficiency was 62.3% due to the locked Ta anode particles. The results of air classification test for the crushed samples showed that optimal air flow are 39㎥/h, 32㎥/h, 20㎥/h. respectively. When the sample were separated with optimal condition, 94.45％ Ta anode containing 97.47 wt.％ Ta anode, 0.93 wt.％ resin. 1.61 wt.％ metal was recovered with 49.39 wt.％ yield.

• Resources Recycling
• /
• v.25 no.1
• /
• pp.40-47
• /
• 2016

Nickel laterite ore is classified into two principal ore types: saprolite (silicate ore) and limonite (oxide ore). Saprolite-type ore characterized by high magnesia and silica contents is treated by pyrometallurgy process. On the other hand, limonite-type ore is subjected to hydrometallurgy process to produce nickel products. Hydrometallurgy process requires that a raw material to meet the demands that Si+Mg contents lower than 10% and Fe content over than 40%. It is therefore required that separation of saprilite-type ore to use nickel laterite ore as a raw material for hydrometallurgy process. In this study, separation of sparolite-type ore and limonite-type ore from nickel laterite ore from New Caledonia has been tried by dry classification. The results show that -5 mm size fraction and +5 mm size fraction of the nickel laterite ore contains mainly limonite-type ore and saprolite-type ore, respectively. To understand the moisture content of the raw ore on the dry classification, nickel laterite ore with different moisture contents of 23.0% and 9.1% were subjected to the dry classification. The results show that drying of the ore makes the separation more efficient as the amount of the fine product, that can be subjected to hydrometallurgy process without further separation or drying operations, was increased.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.97-97
• /
• 2017

천일염의 생산공정은 바닷물(나트륨 농도: 2~3%)을 저수지로 유입시킨 바닷물을 농축하는 1차 증발지(난치)와 2차 증발지(누태)로 보내 일반적으로 2주 정도 증발시켜 나트륨 농도 12~15% 소금물을 만든다. 온도가 낮은 겨울철에는 결정지를 거치거나 2차 증발지의 농축시켜 창고(해주)에서 보관 하는 동안 나트륨 농도 25~27%정도로 상승되어 소금 결정을 이루고 채염하여 창고로 운송한다. 보관창고에서 천일염에서 쓴맛을 내는 간수를 제거한 뒤 선별, 건조 및 포장하는 유통하는 단계로 이뤄진다. 천일염의 생산과정 중 해주는 함수를 저장하여 고농도의 함수를 저장하여 불용분 및 이물질을 자연 침전시켜 맑은 함수를 다음 공정으로 이송시켜 천일염 품질향상에 중요한 공정 중에 하나이다. 그러나 일반적인 염전의 해주는 지붕의 복사열로 인하여 저장중인 해수의 대류로 인하여 침전물이 상승되고 이물질이 부유함으로 인하여 품질저하의 원인이 되고 있다. 또한 해주 구조 및 해주 품질에 대한 자료는 전무한 실정이다. 따라서, 본 연구의 목적은 해주의 깊이에 따른 해수의 대류 방지 깊이 및 품질 변화를 측정하여 고품질 천일염 생산공정에 적용하는데 목적이 있다. 해주분석을 위한 염전은 결정지 채염공정을 공유하는 2개지역 3개 염전을 대상으로 하였으며, 무안, 운남 및 만품지역의 3개소를 선정하여 생산방식이 비교적 동일한 염전을 선정하여 조사 및 분석하였다. 해주의 깊이는 1.0, 3.0, 3.5m인 해주의 시료를 채취하여 Calcium, Magnesium, Sulphate, Chloride 의 함량 분석은 Arena 20 XT 자동흡광분석기 (Automated photometric analyzer)을 이용하여 분석을 하였다. 각 염전에서 채취한 해수의 평균 탁도 값은 해주의 깊이가 깊을수록 탁도 값이 낮은 것으로 나타났다. 해수의 색상 "b" 값은 해주 깊이가 깊을수록 낮은 결과를 보였다. Mg 함량은 전반적으로 15,000~40,000 mg/L 범위의 값을 나타냈으며, Sulphate 함량은 약 30,000~65,000 mg/L 범위의 값을 나타났으며, 깊이가 깊을수록 Mg, Sulphate 함량이 낮아지는 결과를 보였으나 Chloride 함량은 뚜렷한 경향을 보이지 않았다. 실험 결과 해주 깊이에 따른 함수의 품질 차이가 발생하는 것을 확인 할 수 있었으며, 해주의 바닥 깊이가 깊을수록 함수의 불용분 침전, 분리에 효율적인 것으로 판단되었다.

• Journal of Food Hygiene and Safety
• /
• v.30 no.2
• /
• pp.150-158
• /
• 2015

This article reports the development of an effective test procedure for detection of norovirus (NoV) in foods of diverse matrices. In this study, target foods included fermented milk, soybean paste, powders made from uncooked grains and vegetables, sesame leaves preserved in soy sauce, pickled mooli, and mooli. Viral recovery varied depending on the food matrices or elution buffers tested. Buffers were compared to determine effective elution buffers from artificially virus-contaminated foods. The conventional test procedure for concentrating viruses from food (elution-polyethylene glycol(PEG) precipitation-chloroform-PEG precipitation) was modified to save time by eliminating one PEG precipitation step. The modified procedure (elution-chloroform-PEG precipitation) was able to concentrate viruses more effectively than the conventional procedure. It also removed RT-PCR inhibitors effectively. The modified procedure was applied to target food for genogroup II NoV detection. NoV RNA was detected at the initial inoculum levels 3.125-12.5 RT-PCR units per 10-25 g tested food. The use of this newly established procedure should facilitate detection of low levels of norovirus in diverse foods.

• Korean Journal of Food Science and Technology
• /
• v.53 no.5
• /
• pp.593-600
• /
• 2021

In this study, the vacuum distillation process for producing non-alcoholic red wine was optimized via response surface methodology. As a result of optimizing the responses (alcohol content, yield) for independent variables (operating time, boiling point, and temperature difference), 1% alcohol content and 81.15% yield were obtained at an operating time of 24.5 min, boiling point of 65℃, and temperature difference of 8℃. To investigate the physicochemical and sensory properties, non-alcoholic wines with different boiling points (bp 25℃, bp 45℃, and bp 65℃) and a blended wine (4.2% of control wine added) were prepared. As the boiling point increased, the alcohol content decreased, and CI (color intensity) and Hue increased. Blended wine exhibited the highest value and bp 65℃ showed the lowest value in terms of sensory properties. In conclusion, distillation at a low boiling point and blending control wine could be used to prepare non-alcoholic wine with a high preference.